Where is the SRS warning light on a Mercedes?
SRS warning light on console, between front seats, illuminated intermittently or permanently. As mentioned elsewhere in this Forum the light can illuminate when the SRS seat pad sensor connector under the passenger seat is suspect.
How does the SRS seat belt system work?
A; Many.. The SRS system has a pre-tensioner in each seat belt, several air bags, sensors throughout the car to activate same, and a child sensor in the front passenger seat. A; The child sensor adjusts air bag and seat belt level for the front passenger, and effects the functionality of several other devices.
How to replace the SRS seat pad light?
1. At some point, have the codes read, by an inde, (PIC 1 ) as having the seat pad SRS light on will ‘MASK’ other ( emergency tensioning retractor belt and bag) faults. 2. Buy a NEW sensor first, (PIC 2 ) I have not seen ANY signs of wear ( wires, scraping, breaks ) at all. The sensor ‘dots’ fail with use/age. Sensors cost 140 US$ at MB. 3.
How to replace seat sensor on Mercedes SRS?
Tip the seat top down and remove the complete car seat from the car. 11. Remove the connector block and unplug the yellow sensor (PIC 13 ) connector from it’s housing under the seat. 12.Take off the plastic side covers. 13. Loosen the 2 back bolts, (PIC 14-15 ) and remove the 2 front ones, This is optional and done to make the job easier. 14.
Why does my SRS light keep going on?
Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Step 1 Install a new battery; Step 2 Reset SRS/ Airbag light. Instruction on How to Reset the SRS Light on a Mercedes Benz: 1.
How to reset SRS / airbag light on Mercedes Benz?
Find the port that fits the OBD cable and plug the scan tool’s cable into this port. 2. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts. Look at your OBD scan tool and write down the codes it displays. 3. Check your owner’s manual for what the codes mean. 4.
How to resolve SRS warning light fault ( W208 )?
Release the seat covering from around the frame (front and sides only – no need to remove completely) at the base of the seat. Once the cover has been released turn the seat onto it’s back. Lift up the seat cover (front) and expose the seat pad sensor pocket.
What does the SRS light mean on a Mercedes Benz?
What does SRS light mean? SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system.
What does it mean when SRS warning light stays on?
SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system. It is very unlikely that your airbags are going to deploy randomly, but the concern is that they may not deploy…
Find the port that fits the OBD cable and plug the scan tool’s cable into this port. 2. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts. Look at your OBD scan tool and write down the codes it displays. 3. Check your owner’s manual for what the codes mean. 4.
Is there a way to reset the SRS light?
You can’t rest the airbag SRS light with a simple OBD II scanner which gives you the check engine light codes. You will need a more advanced scan tool to reset the airbag light. For around $110-150, which is how much a diagnosis costs anyway, you can get your airbag reset tool.