Where is the fuse panel on a Jeep Commander?
The fuse panel is located under the instrument panel just to the left of the steering column near the brake pedal (behind the cover near the OBD). Mem. Sw, Courtesy Lamp (B+) Final Drive Control Module (FDCM), Heater Ventilation, Air Conditioning (HVAC), Switch Bank.
What are the warning lights on a jeep?
The following are warning lights and indicators found in vehicles built by Jeep. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are nearly 80 of them so be patient!
When did the Jeep Commander XK come out?
The mid-size SUV Jeep Commander (XK) was produced from 2006 to 2010. In this article, you will find fuse box diagrams of Jeep Commander 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
What’s the best way to disconnect a car battery?
Clean any corrosion off of the battery and terminals with a can of spray-on battery cleaner. Disconnect the negative battery cable and then the positive cable with a combination wrench. Clean the battery posts and terminals with the post and terminal cleaning tool, so you have a good connection when you’re done.
How to reset your Jeep engine control module?
3- Once the time has passed you should now turn the headlights “on” and “off” twice to drain the Engine Control Module from any remaining power. 4- Now plug back in the negative terminal and your Jeep ECM should now be reset. To finish off this post , here are a couple of things you should keep in mind.
Clean any corrosion off of the battery and terminals with a can of spray-on battery cleaner. Disconnect the negative battery cable and then the positive cable with a combination wrench. Clean the battery posts and terminals with the post and terminal cleaning tool, so you have a good connection when you’re done.
What happens if I Reset my Jeep ECM?
To finish off this post , here are a couple of things you should keep in mind. Resetting your Jeep ECM will not have any effect on your vehicle’s mileage, Resetting it should not cause any issues between your other module so feel free to this as many time as you want if you’re trying to diagnose a problem with your car. For good measure.
Where is the fuel pump relay located on a car?
The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine. It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by…
Where is the fuel pump control module located?
It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by the ignition or Powertrain Control Module, and when switched on, will provide current to the fuel pump so that it may function.
The fuse panel is located under the instrument panel just to the left of the steering column near the brake pedal (behind the cover near the OBD). Mem. Sw, Courtesy Lamp (B+) Final Drive Control Module (FDCM), Heater Ventilation, Air Conditioning (HVAC), Switch Bank.
The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine. It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by…
The mid-size SUV Jeep Commander (XK) was produced from 2006 to 2010. In this article, you will find fuse box diagrams of Jeep Commander 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Where is the 40 way wiring on a 14v fuel pump relay?
14. Carefully remove and save the 40-way electrical connector wire cover located on the wire side of the connector (Figure 11). NOTE: The plastic tie strap that holds the wire harness to the wire cover must be cut off and discarded (Figure 10).