When to change the oil in a BMW R1200GS?

When to change the oil in a BMW R1200GS?

BMW R1200GS Motorcycle Oil Change The BMW Maintenance Schedule recommends changing the engine oil and engine oil filter at the scheduled 6000m (10,000km) service intervals. See also: R1200GS Engine Oil Q&A BMW R1200GS Engine Oil change without new filter (interim oil change)

How do you change oil on a BMW M54?

With the M54 engine ( E36, E46, E60, E83, E85 series), a 32mm socket will unscrew the filter housing car, but if you have the N52/N54 engine ( E9x, E60, E61, E87, F01 series), then a special adapter is needed. It is best to unscrew these housing caps first, so that the oil in the housing can drain out.

When to change the oil in a BMW transmission?

BMW recommends using only the same fluid in the transmission when topping off the oil level. They do not recommend mixing ATF oil brands and specs so keep track of what oil is in your transmission. Recommended replacement interval: 60,000 miles

Where is the oil filter located on a BMW?

You need some tools before you start the oil change process. Make sure you have handy an oil pan, socket and socket wrenches, and a flat head screwdriver. If you have a six cylinder engine, the oil filter housing is located in the front of the engine bay, near the intake manifold. I’m using the N52, N54 and M54 engines as examples.

How do you change the oil in a BMW 650 GS?

Put some oil on the rubber ring inside the oil filter and insert the oil filter into the motorcycle. It should push in snuggly, but not hard. Reattach the oil filter cover, re-route the black wire in its correct position (if you moved it), and reattach the chain sprocket cover. The specs on the torx screws for the oil filter cover are 10 nm.

Do you need to change the oil on a BMW?

Changing your motorcycle oil and oil filter on a regular basis is the single most important maintenance task you can do to assure the integrity and longevity of your engine. Many BMW riders enjoy performing this relatively simple service themselves.

You need some tools before you start the oil change process. Make sure you have handy an oil pan, socket and socket wrenches, and a flat head screwdriver. If you have a six cylinder engine, the oil filter housing is located in the front of the engine bay, near the intake manifold. I’m using the N52, N54 and M54 engines as examples.

How do you change the oil on a BMW airhead?

On the center stand, remove the engine pan drain plug, drain the oil, replace the oil drain plug using a new crush washer (yes, even if it is the solid aluminum type), top up the oil to the proper mark (NOT screwing in the dipstick when taking a reading is standard for BMW Airheads).

How to remove rear wheel from BMW R1200?

1. Remove the fender (GS models only). 2. Remove the rear wheel (T-50 Torx). 3. Unbolt the Brake Caliper (T-45 Torx) and hang it with some wire to the frame. Note: This sensor build-up looks bad, but really isn’t. That is a normal amount of accumulation for 20K miles and never changed. It looked much better the second and third time.

What kind of engine does a BMW R1200C have?

Fuel-injection technology and sheer brute force pump out 71 lb.-ft of torque. An agile anti-dive Telelever front suspension soaks up the bumps. While antilock brakes deliver quick, controlled stopping power.

How to install final drive on BMW R1200?

Clean and oil the speed sensor O-ring and put it in the final drive, followed by the greased speed sensor and then install the screw, the clamp screw, and the clip. 14. Install the caliper, torque to 24 nm, remember to reinstall the fender holder on the lower bolt. Use the fender bolt to line it up.

How to change the oil in a BMW R1200R?

1. Remove silencer 2. Remove rear wheel 3. Remove filler plug 4. Remove drain plug and drain oil. 5. Replace o-rings if necessary, replace drain plug (20NM) 6. Fill with 180ml transmission oil 7. Replace filler plug (25NM) 8. Fit rear wheel (60NM) 9.

Why does BMW R1200C exhaust smell like smoke?

A couple of weeks ago i started noticing the exhaust has a pretty strong smell. There is a custom pipe on the exhaust so i was thinking it was running a little rich. The other day after it sitting for a a few days thanks to the rain i started it up. I was welcomed by a nice could of smoke coming from the exhaust.

What kind of oil filter do I need for my R1200GS?

R1200 Hexhead & Camhead Kits Includes a 4 pack of brand new OEM Mahle OC306 oil filters with 4 crush washers for all non liquid cooled R1200GS/RT/ST/S/R, K1200S/R/GT (2005 on) & K1600GT/GTL bikes. Also includes the correct STEEL oil filter wrench. These are OEM filters and the wrench will fit the OEM BMW filters as well as our Mann filters.

Where to get an oil change on a BMW?

Munich motorcycles in Myaree is good for all things BMW, and the shop next door is very good for servicing or repairs. (BM bikes unit 6, 9 Hayden court Myaree).

Do you need an oil filter for a BMW?

For some models, oil filters are included in BMW motorcycle oil change kits that also have the required crush washers and other gaskets. You can pick up our Crush Washer Kits, which are conveniently packaged in full sets of the washers needed to change all the drive train oils — no more searching Microfiche diagrams to find them.

Changing your motorcycle oil and oil filter on a regular basis is the single most important maintenance task you can do to assure the integrity and longevity of your engine. Many BMW riders enjoy performing this relatively simple service themselves.

Do you need a Bob’s BMW oil change kit?

Those are here too – either the stock BMW tool or the Bob’s version, recommended for its sure-fit design and affordability. We even stock those little crush washers; you know you need to replace them with each oil change.