How to replace the window regulator in a Jeep Cherokee?

How to replace the window regulator in a Jeep Cherokee?

1 Start Removing the Door Panel 2 Pop the Panel Free 3 Undo the Connecty Bits 4 Pull Back the Vapor Barrier Carefully! This is a very important piece. 5 Pull Off the Sweeper 6 Unplug the Window Regulator Motor. 7 Unbolt the Window Regulator From the Door and the Window. 8 Glass! 9 New and Old. 10 Plug the Plug

How do you replace a power window regulator?

Replace the mounting bolts. Hold each component in the appropriate position as you return the mounting bolts that secure both the power window motor and the regulator. Thread each bolt in by hand first, then use a wrench to tighten them. If a bolt doesn’t thread it properly, remove it and try again to prevent cross-threading them.

How do you remove a power window motor?

Remove the motor and regulator through the access port. With the pigtail disconnected, the power window motor and regulator will no longer be connected to anything inside the door. Reach into the large access port and pull them each out. The two are connected, so pulling one will remove them both.

How can I see the regulator track on my Window?

Peel the plastic moisture barrier away from the door. The adhesive will remain tacky so you can reapply it when you’re done. Once it’s out of the way, you’ll be able to see the 4 black bolts that hold the window regulator track and the 3 gold bolts that secure the regulator motor.

How to replace a window regulator in a Jeep Grand Cherokee?

Once it’s out of the way, you’ll be able to see the 4 black bolts that hold the window regulator track and the 3 gold bolts that secure the regulator motor. Using a 10mm socket, completely remove the 2 marked by the yellow arrows. The rest can simply be loosened and then lifted up and pushed out of the key hole slot when removing the regulator. 7.

How to remove front passenger window in Jeep?

Using the regulator, move the front door glass (1) up or down as required to access the two window regulatorglass release tabs (2) through the access holes in the regulator rails. 5. Using a small round bladed tool (2) or equivalent, release the door glass (1) from the window regulator glass sliders (3).

Why does my window break on my Jeep Grand Cherokee?

A common problem on the 1999-2004 Jeep Grand Cherokee is for the plastic trolley that carries the window up and down to break where the cable that pulls the window attaches. You’ll hear a snap when it does break, and then you’ll likely watch your window slide down into your door.

How do you remove glass from front passenger door?

Press firmly on the what appears to be a glob of grease with a small screwdriver or something similar. While pressing lift the glass upward and it should release. Perform the same procedure on the clip that is located behind the speaker. I did not actually remove the glass from the door.

Using the regulator, move the front door glass (1) up or down as required to access the two window regulatorglass release tabs (2) through the access holes in the regulator rails. 5. Using a small round bladed tool (2) or equivalent, release the door glass (1) from the window regulator glass sliders (3).

A common problem on the 1999-2004 Jeep Grand Cherokee is for the plastic trolley that carries the window up and down to break where the cable that pulls the window attaches. You’ll hear a snap when it does break, and then you’ll likely watch your window slide down into your door.

How do you remove glass from a door?

Unplug the regulator electrical harness and push the connector through the opening in the door panel. 9. Reach through the large lower opening in the door panel, and remove the regulator motor, carriage and track. It can be helpful to lift the glass up in the window track to make some extra room.

Unplug the regulator electrical harness and push the connector through the opening in the door panel. 9. Reach through the large lower opening in the door panel, and remove the regulator motor, carriage and track. It can be helpful to lift the glass up in the window track to make some extra room.

How do you remove a garage door handle?

Lift the door panel from the inside window wipe channel and look down behind the panel. Unclip the latch and lock rods from the door handle tabs. Also disconnect the two wiring harness plugs.