How many warning lights are there on a Saab?

How many warning lights are there on a Saab?

Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are over 30 of them, so search carefully!

Where is the fault code stored on a Saab?

Since a fault code will be stored in your Saab’s OBD computer, you can use an OBD-II scanner to read those codes. When your Saab check engine light comes on, you may notice:

Why does my Saab check engine light keep blinking?

Saab turbocharged engines can have problems with fuel injectors. This will cause excessive smoke from the exhaust on startup and sometimes while driving, combined with rough running and hesitation. The root cause for this is a dirty fuel, which causes build-up on the injectors and poor spray pattern.

What causes MAF sensor to go bad in Saab?

MAF sensor may function fine when the engine is cold then start to malfunction once the engine warms up. A coolant temperature sensor can go bad with time, causing the engine to run rich and preventing it from going into the ‘closed-loop’ mode.

Where are the fuse panels on a Saab 9-5?

Here you will find fuse box diagrams of Saab 9-5 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

When did the first Saab 9-5 come out?

In this article, we consider the first-generation Saab 9-5 (YS3E), produced from 1997 to 2009.

Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are over 30 of them, so search carefully!

Since a fault code will be stored in your Saab’s OBD computer, you can use an OBD-II scanner to read those codes. When your Saab check engine light comes on, you may notice:

Saab turbocharged engines can have problems with fuel injectors. This will cause excessive smoke from the exhaust on startup and sometimes while driving, combined with rough running and hesitation. The root cause for this is a dirty fuel, which causes build-up on the injectors and poor spray pattern.

MAF sensor may function fine when the engine is cold then start to malfunction once the engine warms up. A coolant temperature sensor can go bad with time, causing the engine to run rich and preventing it from going into the ‘closed-loop’ mode.

Why does my Saab check engine light keep coming on?

When your Saab check engine light stays on, it means that the On-Board Diagnostic (OBD) computer has detected a malfunction. The cause could be an engine problem, a fuel system leak, or even an indication of a transmission issue. Since a fault code will be stored in your Saab’s OBD computer, you can use an OBD-II scanner to read those codes.

Can a check engine light be combined with an ABS warning light?

In some cases, it is possible to have a check engine light combined with an ABS/TCS warning light. This issue is usually caused by an ABS/TCS unit internal problem, causing a communication error. The only real solution is to remove the ABS/TCS control unit from the car and send it to a specialist for repair.

What is the owner’s manual for a 1994 Saab 9000?

Owner’s Manual Saab 9000 M 1994 Instruments and controls 5 Interior equipment 27 Doors, locks and lu gage compartment 41 tarting and driving 49 Car care and maintenance 65 Technical data 93 Index 104 Saab Automobile AB 1993 Service Support, Saab Automobile AB Trollhättan, Sweden Printed by: Graphic Systems AB, Gåteborg

Do you need an SRS for a Saab 9000?

REGULAR MAINTENANCE OF THE SRS IS NOT REQUIRED. This Owner’s Manual provides some prac- tical advice on driving and looking after your car.

What are the warning lights on a Pontiac?

Remember that only proper service and repair procedures will ensure the safe and reliable operation of your car.

REGULAR MAINTENANCE OF THE SRS IS NOT REQUIRED. This Owner’s Manual provides some prac- tical advice on driving and looking after your car.

Remember that only proper service and repair procedures will ensure the safe and reliable operation of your car.

What kind of tail lamp does a Saab use?

USED Saab 9-5 Tail Lamp Assembly. Right-Hand Side — Passenger. 2002-2005 9-5. $179.00 Black Carbon Fiber Saab Wheel Center Cap. $38.60 Alernator. (9-5 1998-2003) [5248794] 6 Cyl. Only $677.60 Take care of your Saab. These mud flaps help protect your car body as well as other road-users from flying gravel and splashing water.

What kind of key fob does a Saab use?

2008-2010 9-3 Convertible 1 on vehicle. 2008-2010 9-3 Sport Combi 1 on vehicle. NOT FOR 2003 CV MODELS!!KEY FOB MUST BE PROGRAMMED TO VEHICLE IN ORDER TO FUNCTION!! Will require GM on line security software and Tech 2 programmer. Original P/number is 12783781.Saab 9-3 Alarm Remote Fob/Transmitter.

How much does a genuine Saab headlight cost?

Genuine Saab Right Headlight. Xenon. (9-5)2010-2011) [12842568] $1,023.53 This is a unit that has been remanufactured to fix the common partial screen loss. NOTE: These units are fully functional, but are in used condition. They are not damaged, but cannot be labeled as being in the same cosmetic condition as a new unit still in the box.

Here you will find fuse box diagrams of Saab 9-5 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

When did the second generation Saab 9-3 come out?

In this article, we consider the second-generation Saab 9-3, produced from 2002 to 2014. Here you will find fuse box diagrams of Saab 9-3 2003, 2004, 2005, 2006, 2007, 2008 and 2009, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

Where to buy Saab 9-5 spares in UK?

Search 180+ Saab Breakers And Save £££ on Saab 9-5 Spares With The UK’s No.1 Saab Parts Finder. No Reg? Click here to select MAKE & MODEL

Why is my Saab 9-3 door lock not working?

The central locking door lock mechanisms on Saab 9-3s (and 9-5s) are known to occasionally malfunction/stop working. When you hit the central locking button on the remote, the affected door often won’t lock (or won’t unlock if it was already locked). The issue tends to start out intermittent and then worsen with time.

Where is the door card on a Saab 9-3?

To access the door locking mechanism, we need to remove the door card and disconnect some cabling etc. There are two screws holding the door card in place, both located under the inner handle. You need to carefully prise the handle apart to access them: The two screws have Torx heads, you’ll need a long driver to reach the middle one.

When does the traction control light turn off?

When you turn the key in the ignition, the traction control warning light should come on for around 1 to 2 seconds, and then it should turn off as the vehicle starts. In the event that the light does not go out, it either means that your system has been deactivated, or that another problem has occurred.

How does the traction control system work in a car?

Most modern vehicles have a traction control system in them. This system keeps track of the vehicle’s steering performance and stability. If the vehicle were to lose its traction on the ground, the traction control system will detect this problem and then act accordingly to correct the issue.

How does the stability control system work in a car?

The steering angle sensor calculates the angle of the steering wheel and the rate in which it is being turned. The sensor is positioned in the steering column so that it can track the angle and rate precisely. This sensor is typically used by the stability control system to detect the direction the driver intends to go.

What to do when your traction control warning light comes on?

If a fluke in the TCS system triggered the warning light, it should turn stay off when you restart the engine. If it comes back on, it’s likely time to call a mechanic and get a system diagnosis. Until it’s fixed, drive gently and avoid hard acceleration that could result in the wheels slipping.

What causes the traction control to go offline?

The traction control computer in your vehicle is the “brain” that controls the entire system. A defect, corroded contacts or water damage in this computer can result in the entire system going offline, which will turn on the TCS warning light. As the TCS and ABS often share a computer, this may affect your ABS system and turn on that light, too.

How do you turn off traction control on a car?

Many vehicles with traction control have a switch that lets you temporarily turn it off. The switch is usually marked “TCS Off” or “ESC Off.” Once you switch it off, it will stay off until you either switch it back on or turn off and restart your vehicle.

Is the airbag light on in the Saab 9-3?

If your airbag light is on in your Saab 9-3, the first thing to check is for loose connections under both front seats. If your airbag light is on in your Saab 9-3, the first thing to check is for loose connections under both front seats. Skip navigation Sign in Search Loading… Close This video is unavailable.

Why is my 9-5 airbag light still on?

In that case the most likely cause on a 9-5 is a problem with the clock spring in the steering column which allows the contacts to work. Does the horn still work on the car?

How can I help support Saab Tech Talk?

Help support SaabTechTalk by making a Lump Sum donation or by opening a subscription. Options available are in your Profile/Actions. 2006 9-5 Aero estate – Hirsched. Hold On!!!! The above is the one in my 2007 car that is embedded in the seat base. Earlier cars have a different system…

Do you need specialist to read airbag codes?

Yeah, you’d need a specialist or dealer with a Tech-2, I don’t think there’s anything out there other than opcom that will read things like airbag codes, I think opcom can be a bit hit and miss too on exactly what it supports.

What are the colors of the Saab 9-3?

The Viggen model is available in six colors: Lightning Blue, Monte Carlo Yellow, Steel Gray, Silver, Black and Laser Red. In 2003 a brand new Saab 9-3 was launched. The car was well received and lauded for its good driving characteristics.

When did eeuroparts start making Saab parts?

eEuroparts.com began as a Saab parts company in 2000, and we’ve been expanding our Saab 9-3 parts product line ever since. The Saab 9-3 was launched in 1998 as a redesigned and enhanced successor to the Saab 900.

When did the Saab 9-3 Viggen come out?

In summary, the 1,100 changes were made to modernize the 900 and to make the car match 9-5 in appearance. In 1999 an even more powerful variant of the top model Saab 9-3 2.0T (200hp) called the 9-3 Viggen was released. It was named after the fighter aircraft Saab 37 Viggen.

Where is the relay on a Saab 9000?

[Editor’s note] Similar problems may also be caused by the bulb-check relay, which is the orange relay in the photograph below. This suffers from the same dry-joint problem and may be repaired in the same way. The relay is located in the relay/fuse box in the engine bay near the battery. The relay in question is the large red one in the top left.

Where is the fuse box on a Saab 9-3?

Control module, engine management system; DICE/TWICE; main instrument panel/SID; memory for electrically operated driver’s seat; telephone; cruise control Under the instrument panel next to the steering wheel. Fuse panel in engine bay.

What causes a Saab 93 Convertible to not start?

I have a 2001 Saab 93 convertible that wont start. It started out with all of the cluster warning lights staying on. I would turn the car off and start it again and they would turn off. Then the lights wouldn’t go off at all no matter how many times I turned the car off. all of the gages wouldnt work at all but the car would still start and run.

What does stability control failure on a Saab mean?

Stability control failure means the system will no longer be available to assist the driver maintain traction. You can’t post conmments that contain an email address. SOURCE: service ride and service stability what does that mean?

Why is the anti theft light not blinking?

replace starter and had battery tested good and now car won’t start’ red anti security light is on but not flashing My car has 173330 miles. My car has an automatic transmission. The anti-theft system is engaged. You will need to have the system scanned to see why the system is active. You can try to using a different key to see if it’ll work.

How to reset the anti-theft light on your truck?

Truck won’t start when anti-theft light is blinking. How do I reset it? Is this a good question? 1, Try turning the key and moving the shift from park to drive and back. Then try starting it again! 2. Try your spare key in case the chip has failed in your primary key. 3.

What to do if your car security light is not working?

You can try to using a different key to see if it’ll work. Also, try to open the passenger door with the key to isolate the issue. This will help you find out if the driver’s door switch is causing the system to not deactivate or if the key is the problem.

What to do if your car anti theft light is not blinking?

Leave the key in position for about 10 – 15 minutes. Step 3: Check the anti-theft light again. If it’s no longer blinking, turn the key back to the Off position and allow it to set for a minute or two. This gives the system time to reset or you won’t be able to start your car. Step 4: Start the engine. Attempt to start your engine.

Where is the anti theft device on my car?

It’s located on your dash and will have a blue or red light. Step 2: Turn the ignition to the “on” position. Insert the key into the ignition and turn it to the on position, which activates your accessories but not the engine. Leave the key in position for about 10 – 15 minutes.

When does the anti theft system car wont start?

If the engine does not respond or dies immediately after cranking up, leave the key in that position for 10 minutes. When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

Is there a way to disable the alarm on a Saab?

However, if you don’t want to take the time to lock your Saab every time you exit the vehicle, you’ll find it easier to disable the alarm entirely. Place the key in the ignition and start the vehicle.

Where is the fuse box on a Saab?

Press and hold in the override button until the alarm chirps one time. Lift and secure the hood of the vehicle so it doesn’t fall on you, then look for the fuse box. On Saab vehicles, the fuse box sits to the right of the engine, next to the firewall. Locate the correct fuse. Most fuse boxes have the fuses labeled clearly.

When did the Saab 9 3 convertible come out?

2003-2007 9-3 Sport Sedan 2 on vehicle. 2004-2007 9-3 Convertible 2 on vehicle. 2006-2007 9-3 Sport Combi 2 on vehicle. 2008-2010 9-3 Sport Sedan 1 on vehicle. 2008-2010 9-3 Convertible 1 on vehicle. 2008-2010 9-3 Sport Combi 1 on vehicle.

USED Saab 9-5 Tail Lamp Assembly. Right-Hand Side — Passenger. 2002-2005 9-5. $179.00 Black Carbon Fiber Saab Wheel Center Cap. $38.60 Alernator. (9-5 1998-2003) [5248794] 6 Cyl. Only $677.60 Take care of your Saab. These mud flaps help protect your car body as well as other road-users from flying gravel and splashing water.

Genuine Saab Right Headlight. Xenon. (9-5)2010-2011) [12842568] $1,023.53 This is a unit that has been remanufactured to fix the common partial screen loss. NOTE: These units are fully functional, but are in used condition. They are not damaged, but cannot be labeled as being in the same cosmetic condition as a new unit still in the box.

Where can I get parts for my Saab 9-3?

Whatever you’re looking for, eEuroparts.com will deliver the Saab 9-3 parts you need, fast. As always, free shipping is available on your Saab 9-3 parts order totaling $50 or more.

What are the symptoms of a bad alternator in a Saab 9-3?

Here are the most common symptoms of a bad alternator in a Saab 9-3: The battery light is designed to tell you that there is not enough voltage to properly charge the battery, or that the battery itself is not holding the proper voltage. In rare occasions the service engine soon light may light up.

What should the volts be on a Saab 9-3?

Specifically, you’ll need to set it to 20V DC. With your 9-3 turned off, you’ll connect the negative side of the meter to the negative battery post or wire. You’ll then touch the positive side of the voltmeter to the positive battery wire. With the engine off, you should get a reading somewhere between 12.0 volts and 12.6 volts.

What causes a battery warning light on the dashboard?

See how you can fix the battery warning light on dashboard with this five problem that you can look at. While the battery light might seem like there is a battery problem, but in fact there could be other numerous issue causing the battery light to activate. To see what is really wrong with the car see this video for things you can check.

When did they stop making the Saab 9-3?

In 2013-2014, an unsuccessful attempt was made to resume the production of 9-3 sedans, after which the company lost the rights to the Saab brand.

Which is the first car of the Saab brand?

SAAB Car Manuals PDF & Wiring Diagrams above the page – 9-3, 9-7, Sonnet, 9-2, 9-5, 9000; SAAB EWD s; SAAB Fault Codes DTC . The car company SAAB was created in 1945 by the Swedish aviation concern SAAB AB, the first car of the brand, Saab 92, stood on the conveyor in 1949.

What happens when the crankshaft position sensor goes bad?

If the computer detects a problem with the crankshaft position sensor’s signal, it will activate the Check Engine Light to alert the driver of the problem. A Check Engine Light can also be set off by a wide variety of other issues. Having the computer scanned for trouble codes is highly recommended. 4. Uneven Acceleration

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

Can a bad crankshaft sensor cause a cylinder to misfire?

Should you feel or hear a brief stutter in the engine, it may be a sign of misfiring cylinders from a bad crankshaft position sensor. A failing crankshaft position sensor cannot provide the right information about piston positioning in the engine, causing a cylinder to misfire.

What do the symbols on my car headlights mean?

These symbols are usually blue, green, or yellow in colour. Indicator light means that the vehicles dipped beam is on. Click Indicator light means that there is an exterior light on the vehicle that is not functioning properly. Click Indicator light means your car’s high beam headlights are on, or if the high beam flash function is used. Click

Are there any problems with LED head lights?

LED headlights are relatively new to the automotive industry. Manufacturers use these types of headlights due to their small size and bright light. However, these lights are not compatible with the conventional power system of old cars, which resulted in some issues.

What causes the headlights to turn on automatically?

Headlights that turn on automatically or those that can adjust brightness use light sensors typically mounted in the windshield. Dirt and debris can prevent these sensors from detecting light properly, so clean the windshield if the system doesn’t seem to be working properly.

When does the oil pressure warning light come on?

If you have an oil pressure problem, it’s likely that the light will come on at the end of a long run when the oil is thinnest and the engine (and oil pump) speed is lower. I think you need to get it looked at as soon as possible.

Why does my engine warning light keep coming on?

In the last ten minutes of the journey the orange engine warning light came on and has remained on. Performance is unaffected and a visual inspection of the engine doesn’t reveal any serious (or even new) oil leaks.

Where is the vacuum tube on a Saab?

The only vacuum tube from the front of the car to the ‘box’ on the bulkhead is the one operating the boost by-pass valve; usually when it’s disconnected you get an annoying whistling/dying seal sort of sound.

Where is the twice control module in a Saab?

The TWICE control module is located under the left-hand front seat, screwed to the floor and connected to the wiring harness with a 70-pin connector. TWICE controls the following functions, and TWICE checks the circuits for the rear lights and brake lights. • Lamp check • Seat belt warning • Heated rear seat

What kind of bus system does a Saab 9-3 have?

All Saab 9-3 from M01 are equipped with the Trionic T7 engine management system. The bus system is therefore almost identical to the one fitted on the 9-5. The bus system on diesel cars with EDC15 and diesel pump is unchanged from M98 1/2 and on cars with PSG 16 from M01 1/2.

How to check the ECU on a Saab?

Select the SAAB selection from the main Vehicle Diagnostic Menu. Select the required vehicle. Switch IGNITION ON and then press the ENTER button. PLEASE WAIT TRYING TO COMMUNICATE will be displayed for a few seconds. After communication the ECU identification will be displayed. An example is shown.