How do you start a Hyundai Santa Fe?
Place the starter motor in a vise equipped with soft jaws and connect a fully-charged 12-volt battery to starter motor as follows. 2. Connect a test ammeter (150-ampere scale) and carbon pile rheostats shown is the illustration. 3. Connect a voltmeter (15-volt scale) across starter motor.
How do you replace a starter in a car?
Pull the starter away from the engine. Put the new starter on the engine and tighten the mounting bolts with the socket and ratchet. Reconnect the electrical wires, tightening the nuts with the wrench, and then plug in the wiring harness. Reconnect the speedometer cable to the transmission and tighten it with a wrench.
What are the repair procedures for a Hyundai Santa Fe?
Repair procedures Hyundai Santa Fe DM 2013-2018 Service Manual / Engine Electrical System / Starting System / Starter. Repair procedures 1. Disconnect the battery negative terminal. 2. Remove the air duct and air cleaner assembly. 3. Remove the ETC module. 4. Remove the intake manifold stay (A). 5.
What to do if your starter won’t start?
Put the new starter on the engine and tighten the mounting bolts with the socket and ratchet. Reconnect the electrical wires, tightening the nuts with the wrench, and then plug in the wiring harness.
When does a Santa Fe starter go bad?
When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Santa Fe, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your Santa Fe to crank, but not start.
How to replace Hyundai Santa Fe starter-YouTube?
To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: KUbNYVzq8vxXNoYm) An error occurred while retrieving sharing information. Please try again later.
What is the code for the Hyundai Santa Fe?
The code in the computer after failure should be P1690 or P1693 (or both). After changing the antenna piece near the ignition (180$ at the dealer), the icon shows up and car starts every time…. been around 50 times to far and no issues. Hope this helps 64 people found this helpful. this sounds so similar to whats happening with our 02 santa fe.
Where is the fuel cutoff switch on a Hyundai Santa Fe?
checkingthe crank sensor is a good idea but there is also a fuel cutoff switch under the hood that may have been tripped. its along one of the fenders ( i tink the drivers side. doesnt happen often byt its another thing to check. if its tripped it will click when pressed (theres a little button on top of it) 82 people found this helpful.
When did the Hyundai Santa Fe come out?
In this article, we consider the first-generation Hyundai Santa Fe (SM), produced from 2001 to 2006. Here you will find fuse box diagrams of Hyundai Santa Fe 2004, 2005 and 2006, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Where is the fuse box on a Santa Fe?
The fuse box is located in the instrument panel (on the driver’s side), behind the cover. The fuse box is located in the engine compartment (left-side). Inside the fuse/relay panel covers, you can find the label describing fuse/relay name and capacity. Not all fuse panel descriptions in this manual may be applicable to your vehicle.
Where do I find the starter on my Hyundai?
Crawl under the car and find the starter. It’s near the transmission and looks like a round canister with electrical wires coming from it. Mark the electrical wires using a marker and masking tape, noting the proper location of each one.
Place the starter motor in a vise equipped with soft jaws and connect a fully-charged 12-volt battery to starter motor as follows. 2. Connect a test ammeter (150-ampere scale) and carbon pile rheostats shown is the illustration. 3. Connect a voltmeter (15-volt scale) across starter motor.
Repair procedures Hyundai Santa Fe DM 2013-2018 Service Manual / Engine Electrical System / Starting System / Starter. Repair procedures 1. Disconnect the battery negative terminal. 2. Remove the air duct and air cleaner assembly. 3. Remove the ETC module. 4. Remove the intake manifold stay (A). 5.
What should I do if my starter is not working?
If the pinion does not retract, the hold-in coil is working properly. To avoid damaging the starter, do not leave the battery connected for more than 10 seconds. 4. Disconnect the battery also from the body. If the pinion retracts immediately, it is working properly.