How do you remove a Mercedes Benz radiator?
With the upper hose removed use a flathead screwdriver and remove the clamp and hose from the middle left side of the radiator (red arrow) to the coolant pump (yellow arrow). You do not need to remove the hose from the coolant pump to remove the radiator.
How do you remove the radiator hose from a car?
Once the ends are together, the clamp should be loose enough to slide up the radiator hose, allowing you to remove the hose from the radiator. Some older models may have a screw type clamp. For this you will need a socket or screwdriver to twist the screw on the hose clamp.
What happens when one part of the radiator fails?
Debris running through the cooling system may also cause a blockage to develop in those tight radiator tubes. When this happens, the radiator’s cooling abilities drastically decrease. When one component fails to work properly, other parts throughout the cooling system also run the risk of failure.
Do you need a wrench to remove a radiator?
To remove the radiator, you will need to remove the condenser mounting bolts with a wrench. This allows the condenser to stay in the engine bay and keeps the refrigerant system closed. The condenser mounting bolts are usually near the top corners of the radiator. You will not need to unhook any lines or hoses from the condenser.
How do you remove radiator from Mercedes AMG?
Remove the bolts on the tray in order to remove it. Locate the radiator stop plug underneath your vehicle. Place the radiator drain pan underneath the car, and loosen the radiator stop plug. In order to speed up the drainage process, remove the cap of the coolant reservoir on top of your engine to allow air flow. Figure 6. Drain the coolant.
How do you replace a valve on a radiator?
Unscrew the union nut that attaches the valve to the radiator, then unscrew the valve from the pipe. Take the old valve to a plumbing and heating supply store to find an exact replacement; look carefully to be sure it will fit. You also may need to replace the short pipe that emerges from the radiator.
What’s the best way to take care of a radiator?
First, drain the radiator and remove any paint, primer, or rust from the area of the leak. Clean the surface with a non-petroleum-based cleaner, such as acetone or lacquer thinner, to remove all dirt, grease, and oil. Rough up the surface with a file.
How do you drain water from a radiator?
With a hot water system, water must be drained from the radiator. Turn down the thermostat. Attach a hose to the boiler’s drain valve and run the hose to a floor drain; open the valve to drain the system. Starting at the top floor of your house, open the bleeder valves of all radiators.
Can a Mercedes Benz W124 radiator be replaced?
The radiators on the W124, like any other car, can wear out with time and age. The unit itself is expensive to replace, so before you buy a new one, pressure test the cooling system first and verify the location of any leaks. It will be easier and cheaper to replace a radiator hose or clamp than replacing the whole radiator.
What to do if your radiator hose breaks off?
Hi, similar issues show up on a lot of these older Mercedes. If this piece breaks off you can try to fix it with some epoxy. But it is not a separate part. If you don’t like the idea of fixing it with epoxy, or that does not hold up, you will have to replace the radiator.
How to remove and replace coolant overflow bottle?
HOW TO REMOVE AND REPLACE COOLANT OVERFLOW BOTTLE RESERVOIR TANK ON MERCEDES W208 W202► Our Website: http://mechaniclifestyle.comHey guys, in this video we w… HOW TO REMOVE AND REPLACE COOLANT OVERFLOW BOTTLE RESERVOIR TANK ON MERCEDES W208 W202► Our Website: http://mechaniclifestyle.comHey guys, in this video we w…
With the upper hose removed use a flathead screwdriver and remove the clamp and hose from the middle left side of the radiator (red arrow) to the coolant pump (yellow arrow). You do not need to remove the hose from the coolant pump to remove the radiator.
Where is the radiator connector on a Mercedes?
It is clipped to the bottom of the top radiator bracket. Locate the electrical connector on the back of the cooling fan. Mercedes E550 Cooling Fan Connector Location – Passenger side, behind the fan. Press the connector and pull it to disconnect it. Remove two U clips at each top corner of the radiator.
The radiators on the W124, like any other car, can wear out with time and age. The unit itself is expensive to replace, so before you buy a new one, pressure test the cooling system first and verify the location of any leaks. It will be easier and cheaper to replace a radiator hose or clamp than replacing the whole radiator.
How much water can you put in a Mercedes radiator?
Check capacity in your owner’s manual. Mix Anti-freeze coolant and distilled water in a 50-50 ratio. Most Mercedes have the transmission cooler integrated into the radiator. When you disconnect the transmission line, you may lose up to 1 quart of transmission fluid.
Undo and remove the two lower water hoses from the radiator. You will need to wiggle the shroud around so the outlet pipes clear the shroud when removing it. The radiator is now free and can be lifted from the car.
Where is the radiator on a Mercedes Pelican?
The radiator has two rubber mounts that sit on grommets in the lower cross frame. Sometimes you need to wiggle the radiator around to free it from the lower mounts, just take care that you do not damage it against the fan or condenser. With the radiator gone the shroud can easily be removed from the engine bay.
What should the temp be on a 1983 Mercedes 380SL?
– Motor Vehicle Maintenance & Repair Stack Exchange Proper operating temp for a 1983 Mercedes 380SL? My 1983 Mercedes 380SL seems to be running hotter than I like. It settles down at right at 100 C by the instrument panel temp gauge after running at highway speed for 10 minutes or so.