How do you change the clutch on a Pontiac Vibe?
Use some proper 6mm bolts to attach it later.7.Remove the 2 screws holding the vacuum control relay on the front of the air cleaner lid.8.Unplug all the connectors to the air cleaner lid.9.Remove air cleaner to throttle body hose.10.Pull off the other vacuum control relay from the back of the air cleaner lid.
Where is the lifting eye on a Pontiac Vibe?
4. The 2ZZ engine does not have a front engine lifting eye from the factory. I guess they had to remove it in order for the cool engine cover to fit. I took the one off the back of the engine and bolted it to the provided spot on the left front corner of the engine head.
How do you change the clutch on a Toyota?
Use a 10mm-1.25 tap and clean out all of the threads on the flywheel mounting holes. They will be full of thread locker from the old bolts. 29. Install the flywheel with new mount bolts. The Toyota part number is 90910-02103. There are 8 of them. Torque in a star pattern in three passes until you get to 35 lb/ft.
How much does it cost to replace a clutch?
It only cost me $35.00. This clutch had 60K miles of easy driving. It really started to go south at 45K we just milked it for a while. 28.Use a 10mm-1.25 tap and clean out all of the threads on the flywheel mounting holes. They will be full of thread locker from the old bolts.29.Install the flywheel with new mount bolts.
How much does it cost to change a Pontiac Vibe clutch?
Get it surfaced even if it looks good. It only cost me $35.00. This clutch had 60K miles of easy driving. It really started to go south at 45K we just milked it for a while. 28.Use a 10mm-1.25 tap and clean out all of the threads on the flywheel mounting holes.
How many miles does a 2005 Vibe have?
I own a 2005 Vibe, automatic transmission, base model, purchased new. At 33,000 miles and just over the 36 month warranty, it began to shift roughly from 1st to 2nd gear, and the check engine light came on. This happened intermittently for not quite 2 weeks, so I took it to a nearby Firestone.
Is there a recall on the GMC vibe?
Bottom line it seems GMC should have recalled these vehicles because not only did engine light just go on, but the car was jerking so bad I almost got into a serious accident just trying to get to the garage. I own a 2005 Vibe, automatic transmission, base model, purchased new.
Where is the vacuum on a Pontiac Vibe?
There is a small vacuum accumulation chamber on the back of the lid. Be very careful and pull off the vacuum hose from the nipple. I ended up breaking the nipple off when I did it.
Use some proper 6mm bolts to attach it later.7.Remove the 2 screws holding the vacuum control relay on the front of the air cleaner lid.8.Unplug all the connectors to the air cleaner lid.9.Remove air cleaner to throttle body hose.10.Pull off the other vacuum control relay from the back of the air cleaner lid.
Where can I find the 2013 Pontiac Vibe?
Vibe Of The Month (VOTM) and Member Of The Month (MOTM) central discussion area. Last post Re: 2013 Vibe of the Year Vot… Park your vehicle in a thread here – list your vehicle info, pics, etc. all in one place. Last post Re: Possibly selling a terrif…
What kind of racing does the Pontiac Vibe do?
Discussion of LEGAL Vibe & Matrix racing events, autocross, drag racing, closed track road racing, and technical racing aspects. [Disclaimer] Last post Re: remote start add on sets …
There is a small vacuum accumulation chamber on the back of the lid. Be very careful and pull off the vacuum hose from the nipple. I ended up breaking the nipple off when I did it.
4. The 2ZZ engine does not have a front engine lifting eye from the factory. I guess they had to remove it in order for the cool engine cover to fit. I took the one off the back of the engine and bolted it to the provided spot on the left front corner of the engine head.
Use a 10mm-1.25 tap and clean out all of the threads on the flywheel mounting holes. They will be full of thread locker from the old bolts. 29. Install the flywheel with new mount bolts. The Toyota part number is 90910-02103. There are 8 of them. Torque in a star pattern in three passes until you get to 35 lb/ft.
What to do if your clutch pedal keeps sticking to the floor?
Step 3: Grab a pry bar and push the slave cylinder pin back into its rest position The clutch pedal should return to its rest position as well. Push down on the clutch pedal and see if will return. If the pedal stays on the floor, then the slave cylinder may have an internal leak if there is no external leakage.
Where is the clutch switch on a manual transmission car?
Manual transmission vehicles are equipped with a clutch safety switch that is installed on the vehicle’s pedal mechanism.
Manual transmission vehicles are equipped with a clutch safety switch that is installed on the vehicle’s pedal mechanism.
What happens to the clutch when the pedal is depressed?
The clutch safety switch is designed to close and provide electricity when the pedal is depressed. However, if the switch fails, it will not be able to provide power for the starting circuit.
Is there a way to disable the ABS system?
However, they are all controlled by a central relay that is located in the main relay panel inside your engine compartment. If you ever have to disable your ABS system, the relay is the most direct and effective way to handle it. Pop your hood and remove your negative battery cable. Locate your main relay box.
How do you replace ABS sensor on Toyota?
Remove the lug nuts and take off the rear wheel. Spray penetrating oil on all the bolts. Disconnect the ABS sensor connector. Remove the brake caliper guide bolts. Disconnect the parking brake cable. Use a breaker bar to remove the brake caliper bracket bolts. Remove the rotor from the wheel hub.
How do you remove an ABS module from a car?
Unbolt whatever bracket or bolts are used to mount the ABS module and solenoid block to the car. This configuration will greatly depend on the make and model of car you are working on. Step 5: Remove the ABS module from the solenoid block. Remove the bolts that attach the module to the solenoid block. Gently pry the module from the block.
Do you need to remove flare end of ABS control module?
Make sure all the brake lines are tight and the flare end is firmly seated as you tighten the brake lines. Sometimes, this can be an issue. If it is, you will need to remove the leaking brake line and take a closer look at the flared end.
When do you need to replace the clutch assembly?
When these fingers are out or with no pressure on them the clutch is engaged. When replacing the clutch assembly it is highly advised to replace the throwout bearing because it has a high failure rate. Some throwout bearings are attached to the clutch slave cylinder which should be replaced as a unit.
What to do before replacing a clutch disc?
The part of the disc that is protruding outward must go toward the pressure plate or the clutch will not release so it’s important to install the disc in the proper direction. Also it is important to use brake cleaner to remove grease and dirt from the flywheel and pressure plate clutch contact surfaces before installation.
How to replace clutch and throw out front wheel drive vehicle?
How to Replace a Clutch and Throw Out Bearing Front Wheel Drive Vehicle | Step by Step! – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
Can a rear wheel drive clutch be replaced?
4. Replace Pilot Bearing: On rear wheel drive and some front wheel drive cars the clutch will have a pilot bearing which is designed to support the input shaft of the stick shift transmission. If this bearing locks up or becomes worn out it allows the input shaft to wonder and will cause the clutch to not disengage.
When do you need to replace a clutch pedal?
The flywheel below is what a the typical wear pattern looks like during a clutch replacement and can be re-machined which must be done anytime you are servicing the clutch. If this step is skipped when the new clutch is installed you will have a good chance that it will chatter when the clutch pedal is released and the job will need to be redone.
Which is the correct way to install a new clutch?
Install the New Clutch: This part is very important! The clutch disc can go onto the pressure plate in either direction but only one direction is correct. The part of the disc that is protruding outward must go toward the pressure plate or the clutch will not release so it’s important to install the disc in the proper direction.