Can you change the rear wheel bearings on a Toyota?
Replacing the rear wheel bearings on a car is a great place to start for at-home mechanics, as you don’t need to fully lift the car or work with any really complicated parts. This video will teach you everything you need to know to change out the rear wheel bearings on any Toyota car.
How do you replace a wheel seal on a Toyota?
You should be able to remove and install this seal by hand. Just pop it out, push the new one in, and apply grease to the seal lip. To begin reassembly, place the backing plate onto the axle shaft, then the new wheel bearing, and then the bearing retainer.
When to replace rear wheel bearings and seals?
When the stock breather is unable to vent the diff, the internal pressure will find relief somewhere in the system: usually at the axle seal. So, if you have a leaking seal, be sure to check the breather for proper operation. Or better yet, replace it with an extended breather. The brake assembly and axle/backing plate prior to removal.
How does SST work on rear wheel bearings?
The SST bolts to the bearing retainer/brake backing plate assembly using the original studs and nuts and then the whole thing is placed in the press. A few pumps later, the bare axle shaft should drop free from the rest of the assembly.
How to change wheel bearing and hub repair?
The hub assembly is MOOG 512218. Even though only one wheel bearing hub was bad, it’s always recommend to replace both sides of any wheel part repair. Thats what the auto guys tell me anyway. I would say this repair is really easy. Not much harder than changing a tire. I set the torque wrench to 45lbs for the four hub bolts.
https://www.youtube.com/watch?v=OJE35juQWM8
How do you replace rear axle retainer on Toyota Tundra?
Just take the C-clip and see if you can fit it in the groove on the axle. To get the old retainer off, pry it apart with a flat bladed screwdriver in the slot you cut into it with the cutoff wheel and slip it off. Next, put the new bearing retainer on the axle shaft, followed by the old retainer and pipe. Pound that sucker home.
How many axle bearings do you need for Toyota Tundra?
Luckily, a local Toyota dealer had everything I needed: two axle bearings, two inner seals, two outer seals, two bearing retainers, and one C-clip (I had to reuse one of them). On a repair this involved, I wouldn’t dare use aftermarket parts.
Why is my rear axle not working on my Toyota Tundra?
The clackity-clack noise was a big clue. It took me two full days of researching on the internet to get to the point to where I felt confident about pulling the axles, buying the correct parts, and at least taking the axles to a machine shop.
How to do rear axle wheel bearing and seal replacement?
Toyota Pickup Rear Axle Wheel Bearing/Seal Replacement. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.
What causes an axle seal to fail on a Toyota?
Common causes of axle seal failure are plugged differential breathers or worn wheel bearings. Less common causes can be a bent axle housing or shaft. When the stock breather is unable to vent the diff, the internal pressure will find relief somewhere in the system: usually at the axle seal.
How to replace rear axle bearing on 1998 Toyota 4Runner?
In this video I will show you how to replace the rear axle bearing on a 1998 Toyota 4runner with abs. I use a fixture that was made out of an used axle housing from the junk yard. Using this method you can remove the axle bearing, lock rings and reluctor ring at the same time without cutting them off.
How long does it take to replace rear wheel bearing assembly?
This easy DIY is to replace the entire REAR hub bearing assembly and takes about 50 minutes. – the OEM Toyota rear hub bearing assembly WITH ABS is much cheaper ($135) than the one without ABS ($260) and still fits cars without ABS.
How do you replace a rear suspension hub?
While holding the backing plate and taking care not to disturb the brake parts and brake line, pull the hub out of the suspension arm. Once it is out, reinsert the bolts to hold the backing plate to the suspension arm so that it doesn’t hang by the brake line. 10. Line up the bolts and insert the new hub. Torque the bolts to 45 ft·lbf.