Where to find SPN code for 16 engine?

SPN codes description SPN Code SPN Name SPN Description 16 Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B.

What is the SPN code for the fuel filter?

SPN Code: SPN Name: SPN Description: 16: Engine Fuel Filter Differential Pressure (see also SPN 1382) Differential pressure measured across the fuel filter located between the fuel tank and the supply pump. See SPN 1382 and Figures SPN16_A & SPN16_B. 18: Engine Fuel Pressure (Extended Range) 19: Engine Oil Pressure (Extended Range) 20

What is the fault code for an Allison Transmission 3000?

Off. Off. Off. Sample control at excess temperature. Holds 4 transfer. Torque converter lock ban. Disables adaptation gear. Off. Prohibition on blocking the torque converter. DNA ON. ON. Off. ON. Only neutral, back and second gear. Ban converter clutch switch adaption is off ON. DNS, SOL OFF, actively hydraulic control. ON. Off. ON. SOL OFF DNA.

Which is the best SPN for an 82 engine?

It is recommended that SPN 3609 be used as it has better resolution. 82 Engine Air Start Pressure Gage pressure of air in an engine starting system that utilizes compressed air to provide the force required to rotate the crankshaft.

What causes the p0015 OBD-II trouble code?

P0015 is the OBD-II generic code indicating the engine control module (ECM) has determined that the exhaust camshaft timing for bank 1 is more retarded than what the ECM has commanded it to be. The over-retarded timing condition can be during the advancing or retarding phase. What causes the P0015 code?

What should I do if I have a p0125 problem?

To repair the P0125, you should use a professional scan tool to check for other codes associated with the P0125 to diagnose the situation. Analyze data from the engine control module. Although it’s often assumed that the thermostat is the problem, that is not always the case.

What is the diagnostic code for a check engine light?

Some Vehicle Specific Codes. Full list of OBD II Diagnostic Trouble Codes. If your Check engine light is on you may have a serious problem. Scan your codes and follow the chart to determine what the code means. Some parts stores will scan your codes for free. Autozone is one place that will give you the code number.

What does Bank # 1 mean on a p0015 DTC?

That consists of a few different components but the P0015 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine light will be illluminated and the code will be set. Bank #1 is the side of the engine that contains cylinder #1.

What does fault code p156f stand for?

P156F = Vehicle speed sensor – Voltage too high or short circuit to supply on ECU (D420) pin (B12) P1570 = Engine oil temperature – Data erratic, intermittent, or incorrect during engine warm-up P1571 = Engine oil temperature – Data erratic, intermittent, or incorrect

What is the SPN for parking brake not set?

Parking Brake Switch Switch signal which indicates when the parking brake is set. In general the switch actuated by the operator’s park brake control, whether a pedal, lever or other control mechanism (see also SPN 619 and 5275).00b = Parking brake not set 01b = Parking brake set 10b = Error 11b = Not available 72

What is the SPN on my Volvo D13h?

Second opinion] I have code SPN 5246 FMI 0 on my Volvo D13H 2011 256k miles. It says DEF tank low Derate to 5 mph, but my DEF tank is full. I can’t clear this code and Tech Tool isn’t much help in my diagnosis.

What are the fault codes for Detroit Diesel engines?

DETROIT DIESEL Engine Fault Codes list DTC Code Description DDEC V Circuit 11 P 187 4 Chain PTO. Short circuit in the power 11 P 187 7 control system PTO wrong answers 12 P 187 3 Chain PTO. Short circuit in the ground 13 P 111 4-level circuit antifreeze. Short circuit in the ground 13 P 111 6 second-level circuit antifreeze.

What does SPN stand for on a body controller?

DEFINITIONS •“SPN” represents the Suspect Parameter Number. This number identiﬁes the item for which diagnostics are being reported. •“FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. 2 BODY CONTROLLER DIAGNOSTIC TROUBLE CODES (S08327)

Which is the correct SPN 91 or 974?

NOTE—See SPNs 91 and 974 for additional accelerator position parameters. 30 Engine Crankcase Blowby Pressure 31 Transmission Range Position Not referenced in J1939-71 32 Transmission Splitter Position The current position of the splitter cylinder. 33 Clutch Cylinder Position Not referenced in J1939-71 36 Clutch Plates Not referenced in J1939-71 37

Which is j-1939 fault code source address?

SS 1033423 : J-1939 Fault Code Source Address (SA), Suspect Parameter Number (SPN), and Failure Mode Indicator (FMI) Descriptions 1 SS 1033423 : J-1939 Fault Code Source Address (SA), Suspect Parameter Number (SPN), and Failure Mode Indicator (FMI) Descriptions

Which is the diagnostic code for engine control module?

SAE J1939 FMI Table FMI SAE Text 0 Data valid but above normal operational 1 Data valid but below normal operational 2 Data erratic, intermittent or incorrect 3 Voltage above normal, or shorted to high

How are diagnostic trouble codes set on an ECM?

The electronic control units (ECUs) that communicate on the SAE J1939 data link, communicate according to the SAE J1587 standard. The diagnostic trouble codes (DTCs) set by the ECUs contain information that is described by the following abbreviations.

When to use SPN 3216 / FMI 2 fault code?

SPN 3216/FMI 2 Description This fault code sets when difference between the expected NOx ppm and the actual NOx ppm is greater than 200 ppm. Monitored Parameter Aftertreatment Inlet NOx Sensor Typical Enabling Conditions (Common Subset for all Engines) General Enabling Condition: Engine is not in regeneration and operating at high speed and loads

Navigation