Where is the CPS sensor on a C240 2001?
I have a C240 2001, the dealer indicated I need to replace the CPS Crankshaft Position Sensor, I did read through the posts and did order the sensor and remove the engine cover, although it is indicated that the CPS is located in the driver side between the engine and the firewall, I could not even insert my hand though all the hoses and cables.
Where is the crankshaft position sensor on a Mercedes Benz?
Locate the crankshaft position sensor (CPS) on driver’s side, towards the rear of engine. Back of engine, near the firewall. This opens in a new window. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. This opens in a new window. Remove bolt. Remove the crankshaft position sensor.
How do you replace a CPS sensor on an engine?
Back of engine, near the firewall. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. Remove bolt. Remove the crankshaft position sensor. You will have either an E8 or E10 bolt that holds the CPS sensor in place. Install new sensor.
What happens if the crank position sensor fails?
Failed crankshaft position sensor can also impact the idling, the acceleration, or even your transmission shifting. In some cases, it can cause your transmission to go into limp mode. You may also notice an increase in engine vibrations. The check engine light is usually illuminated on your instrument cluster.
Back of engine, near the firewall. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. Remove bolt. Remove the crankshaft position sensor. You will have either an E8 or E10 bolt that holds the CPS sensor in place. Install new sensor.
Locate the crankshaft position sensor (CPS) on driver’s side, towards the rear of engine. Back of engine, near the firewall. This opens in a new window. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. This opens in a new window. Remove bolt. Remove the crankshaft position sensor.
What are the symptoms of a bad crankshaft position sensor?
Cost of Replacing a Bad or Failing Crankshaft Position Sensor. Common signs of a faulty crankshaft position sensor include issues starting the vehicle, intermittent stalling, and the Check Engine Light coming on. Our certified technicians can come to you and diagnose the problem.
How much does it cost to replace the crankshaft position sensor?
Crankshaft Position Sensor Replacement Cost? While the prices vary based on your location the average cost of replacing the crankshaft position sensor at an auto mechanic or the Mercedes-Benz dealership vary between $250 and $400. The crankshaft position sensor cost between $100 and $150 at the dealership, that’s for the parts only.
What are fault codes related to the crankshaft position sensor?
Fault codes related to the crankshaft position sensor are: P0335 Crankshaft Postion Sensor A Circuit Malfunction P0336 Crankshaft Position Sensor A Circuit Range / Performance P0337 Crankshaft Position Sensor A Circuit Low Input P0338 Cranshaft Position Sensor A Circuit High Input P0339 Crankshaft Position Sensor A Circuit Intermittent
Where is the crankshaft position sensor on a Honda Accord?
Locate the crankshaft position sensor (CPS) on driver’s side, towards the rear of engine. Back of engine, near the firewall. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. Remove bolt. Remove the crankshaft position sensor.
Fault codes related to the crankshaft position sensor are: P0335 Crankshaft Postion Sensor A Circuit Malfunction P0336 Crankshaft Position Sensor A Circuit Range / Performance P0337 Crankshaft Position Sensor A Circuit Low Input P0338 Cranshaft Position Sensor A Circuit High Input P0339 Crankshaft Position Sensor A Circuit Intermittent
Locate the crankshaft position sensor (CPS) on driver’s side, towards the rear of engine. Back of engine, near the firewall. Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. Remove bolt. Remove the crankshaft position sensor.