What is the value of a 1970 Honda Trail 90?
Values
| Excellent | $2,745 |
| Very Good | $1,615 |
| Good | $800 |
| Fair | $570 |
| Poor | N/A |
How much did a Honda Trail 90 cost new?
With its gallon-and-a-half gas tank and 70 to 80 mpg, you could figure on well over 100 miles on the road before needing to top up. Dry weight was about 180 pounds. Perhaps the most amazing feature of the model was the sticker price – under $350.
Is a Honda Trail 90 2 stroke?
The Honda 90 Trail CT90 was produced for 10 more years until 1969 by the Honda CT110 Trail bike, which was essentially the same bike with a larger engine….Honda CT 90 Trail 90.
| Make Model | Honda CT 90 Trail 90 |
|---|---|
| Year | 1966 – 79 |
| Engine | Four stroke, single cylinder, SOHC, 2 valves |
| Capacity | 89.5 cc / 5.4 cu-in |
| Bore x Stroke | 50 x 45.6mm |
How much is a 1974 Honda Trail 90 worth?
Values
| Excellent | $3,155 |
| Very Good | $1,805 |
| Good | $925 |
| Fair | $565 |
| Poor | N/A |
How do you adjust the carburetor on a Honda Trail 70?
Twist the throttle grip to a full throttle position. Close the choke, using the lever on the left side of the carburetor. Listen to the engine for an increase in rpm. The main jet is too small, creating a lean air-fuel mixture, if the engine speed increases with the choke closed.
How fast will a Honda Trail 90 go?
The Motorcycle is capable of reaching a maximum Top Speed of 45 MPH.
How much is a 1971 Honda Trail 90 worth?
What kind of carburetor did a Honda Trail have?
Honda’s 1970 CT-series, consisting of the Trail 70 and 90, were small single-cylinder motorcycles that were intended to be used both on and off of paved roads. Both motorcycle styles used a simple carburetor to provide a combustible mixture of air and fuel to the engine.
How to adjust the carburetor on a Honda CT90?
Adjusting the carburetor on a Honda CT90 – YouTube Same method is used on other small bike carburetors. Note that this should be done on a warm engine and choke off. If you can’t get an initial idle at all th… Same method is used on other small bike carburetors. Note that this should be done on a warm engine and choke off.
Why are the fuel lines on my Honda CT90 not working?
I RECENTLY PULLED MY CARB AND DIDN’T PAY ANY ATTENTION TO HOW I REINSTALLED THE LINES. MAYBE THATS WHY IT WON’T START NOW. Are you sure the fuel selector is in the correct possition, hard to read?
How do you remove the gas from a carburetor?
Empty the gasoline from the float chamber into a gas can, using a funnel. Remove the float chamber from the carburetor, using a Phillips-head screwdriver. Remove the main jet, located at the end of the center tower on the bottom of the carburetor, using a 90-degree angled flat-head screwdriver.
Honda’s 1970 CT-series, consisting of the Trail 70 and 90, were small single-cylinder motorcycles that were intended to be used both on and off of paved roads. Both motorcycle styles used a simple carburetor to provide a combustible mixture of air and fuel to the engine.
How many Honda CT90 carburetors are left in stock?
Only 4 left in stock – order soon. . Only 15 left in stock – order soon. . . Only 16 left in stock – order soon. . Only 3 left in stock – order soon. . Only 7 left in stock – order soon.
How to fix a leaking carburetor on a motorcycle?
Carburetor / Carb Leaking Gas? How to Fix / Repair it. Motorcycle Honda DIY Tutorial clean – YouTube
Where is the main jet on a Honda Trail?
Remove the main jet, located at the end of the center tower on the bottom of the carburetor, using a 90-degree angled flat-head screwdriver. A CT70 will have a No. 58 main jet, while a CT90 will have a No. 72 main jet. Screw a larger No. 60, or No. 75 for a CT90 model, main jet into the center tower.