What is the density of rubble?

What is the density of rubble?

The particle size distribution mostly meets the requirements of the aggregate grading curves. The bulk density ranges from 1,86 g/cm3 to 2,33 g/cm3.

What is the density of crushed stone base?

Density of Some Common Building Materials

Material Density
Crushed Stone 100 lb/ft3 1,600 kg/m3
Earth, loam dry excavated 90 lb/ft3 1,440 kg/m3
Earth, packed 95 lb/ft3 1,520 kg/m3
Glass, window 161 lb/ft3 2580 kg/m3

What is the density of aggregate?

Most aggregates have a relative density between 2.4-2.9 with a corresponding particle density (Mass) of 2400-2900 kg / m3 (150-181 lb / ft3).

What is the density of concrete in kg m3?

2242 kg/m^3
Density of Concrete

Bibliographic Entry Result (w/surrounding text) Standardized Result
Conversion Factors, Material Properties and Constants, Edward Boyden, MIT. “Density Concrete 2242 kg/m^3” 2242 kg/m3 (conventional)

What is rubble Soling?

Soling is the process of hand packing rubble stones one adjacent to another, to provide a stable base to the foundation and footing, before concreting work. Rubble or boulder soling is done to enhance the bearing capacity of the soil, where hard strata are not available.

What is the density of brick?

around 2000 kg/m3
The density of solid clay bricks is around 2000 kg/m3: this is reduced by frogging, hollow bricks, and so on, but aerated autoclaved concrete, even as a solid brick, can have densities in the range of 450–850 kg/m3. The term “frog” can refer to the indentation or the implement used to make it.

What is the density of wet sand?

Wet Sand: Wet sand has been standing in a natural setting and naturally compressed that is now wet and its density is 1922 kg/m3.

What is the wet density of concrete?

Concrete density in lb/ft^3:- density of concrete is around 133 lb/ft^3 for plain cement concrete in dry mix and 150 lb/ft^3 in wet mix and for reinforced concrete it will be 156 lb/ft3 based on Imperial or US customary system of measurement.

Why do we do rubble Soling?

Rubble soling is done to prepare the uniform level surface on Hard Base or on backfilled surface to work clearly and above rubble soling PCC work will be done for plain level surface. If any level difference in base of the ground then we are doing plum concrete and rubble soling with the heap of rubble and PCC.

How is rubble Soling done?

Soling should be laid in one layer of 230mm or 150mm depth or specified thickness of soling with a tolerance of 25mm. After packing the stones properly in position, the interstices between them should be carefully filled with quarry spoils or stone chips of larger size possible to obtain a bard, compact surface.

Is brick high density?

The density of solid clay bricks is around 2000 kg/m3: this is reduced by frogging, hollow bricks, and so on, but aerated autoclaved concrete, even as a solid brick, can have densities in the range of 450–850 kg/m3.

How big is a base for rubble Soling?

Rubble Soling is a base structure of any foundation which is located under the Plain Cement Concrete of any type of Foundation like Footing, Raft, Road, Trimix, etc. general thickness of rubble soling is 230mm to 300mm.

How to do rubble stone Soling at home?

Following Drawing are need to read to execute the rubble soling work at site. 2 Visit Nearest rubble stone quarry and check the quality of the material. 3 Final the Stone which is must be basalt stone and needs to make with hand-packed or rock on rock technology.

What kind of labour is used for rubble Soling?

Labour: Skilled Labour which are expert in stone work. There are two types of rubble soling which are commonly used in construction industry.

What should be done after compaction of rubble?

After compaction, give the required slope or level and dense sub-base and the surface should present clean look. Adequate care should be taken by the contractor while laying and compacting the rubble soling to see that concrete surfaces in contact with soling are not damaged.

https://www.youtube.com/watch?v=_-B0WSF9zlc