Is there a blend door fix for the Jeep Grand Cherokee?
Both fixes are rock solid and will outlast your GC. Blend Door Installation We have three different blend door kits for the GC. The video shows the process for the installation through the glove box for the standard HeaterTreater and the Dual Control Heatertreater.
How to remove the blend door actuator on a jeep?
Remove the lower portion of the heater duct. You can now visually inspect the blend door actuator up against the center console, attached to the blend box, but the screws will seem impossible to remove! To get to those screws, you must remove the upper portion of the heater duct. It’s made as a clam shell so it comes apart in two pieces.
Do you have to remove dash to replace blend doors?
The tech manuals say you have remove the entire dash to replace the blend doors; you do unless you are willing to make a simple cut with the Dremel tool. Here’s what was going on with my WJ A/C: Sometimes it would be cold, sometimes it would be hot, sometimes driver side was cold but passenger side was hot.
Where is the blend door motor located on a jeep?
There is no electronic diagnosis available for your Jeep®. Physically check the operation of the blend doors by removing the glove box. Remove the blend door motor which is located to the side of the opening. The motor is held in place with two Phillips screws.
Can you replace blend doors on a Jeep Grand Cherokee?
Thought I’d share my experience of replacing blend doors on my WJ without removing the entire dash. The tech manuals say you have remove the entire dash to replace the blend doors; you do unless you are willing to make a simple cut with the Dremel tool.
Remove the lower portion of the heater duct. You can now visually inspect the blend door actuator up against the center console, attached to the blend box, but the screws will seem impossible to remove! To get to those screws, you must remove the upper portion of the heater duct. It’s made as a clam shell so it comes apart in two pieces.
The tech manuals say you have remove the entire dash to replace the blend doors; you do unless you are willing to make a simple cut with the Dremel tool. Here’s what was going on with my WJ A/C: Sometimes it would be cold, sometimes it would be hot, sometimes driver side was cold but passenger side was hot.
Where can I get a blend door repair kit?
These kits, brought to you by Gray’s Garage, LLC (also manufacturer of the seat track repair products – www.seattrackrepair.com ) will allow you to again be able to adjust the temperature on your Jeep climate control system by relocating your blend door actuator (single zone systems) or by inserting a repair shaft (dual zone systems).
What is blend door actuator for Jeep Grand Cherokee?
For information on how to diagnose your blend door problem as well as detailed product information, please click on the products below or use the “Shop” button above. JEEP OEM PART #5143183AA Blend Door Actuator to Blend Door Drive Shaft NOW AVAILABLE – See below or click on the “SHOP” button above.
These kits, brought to you by Gray’s Garage, LLC (also manufacturer of the seat track repair products – www.seattrackrepair.com ) will allow you to again be able to adjust the temperature on your Jeep climate control system by relocating your blend door actuator (single zone systems) or by inserting a repair shaft (dual zone systems).
How can I Fix my Jeep Grand Cherokee?
Follow me for an adventure of a lifetime: Twitter: OmegaGreedAK47 Instagram: OmegagreedAK47 Check out my Website http://www.geekswithcars.com/ First Time Off-Roading in my STOCK Jeep Wrangler JLU! // Jeep JL Off Roading Rowher Flats OHV An error occurred while retrieving sharing information.
What should I do about my Jeep Cherokee blend door?
This is a kit to do a complete repair on the blend door malfunction that is common to the 97- 01 Jeep Cherokee. Every Cherokee in this range either has, or will have, this common failure. The pictures show the hardware provided for the fix.
For information on how to diagnose your blend door problem as well as detailed product information, please click on the products below or use the “Shop” button above. JEEP OEM PART #5143183AA Blend Door Actuator to Blend Door Drive Shaft NOW AVAILABLE – See below or click on the “SHOP” button above.
How do you install a Grand Cherokee door?
Install the cutout plastic housing back into place and seal with provided foam tape. Install drive motor and screws (or clip). Close glove box and reinstall rubber stop tabs. Lifetime warranty against defects or failure of our product.
Why is my Jeep JGC blend door not working?
What I discovered was this is a very common problem with my model of JGC (1999-2004). I love my Jeep, but the person that designed this blend door actuator system needs to find new work. The design is inherently weak, and relies on a calibration phase that puts intense pressure on the weakest points in the system.
How do you remove the air box from a jeep?
Just pull the o-ring off and put back into the hole on the box. Many of the Intake manufacturers have the detailed step by step on installing their intakes. Part of the that would be the full removal of the air box. I don’t have a link but that should help.
Where is the second motor on a Jeep Grand Cherokee?
A second motor is added on the front side of the box to control the back (passenger) door. The repair also requires modifications to the glove box storage area to make room for the second motor.
How do you remove an air intake from a jeep?
It’s on there with 3 rubber o-rings on 3 studs, snug fitted. Just yank it up, you wont hurt anything. The o-rings may come out still installed on the box or still stuck on the studs. Just pull the o-ring off and put back into the hole on the box. Many of the Intake manufacturers have the detailed step by step on installing their intakes.
What to do if your Jeep Grand Cherokee blend door fails?
The cheap plastic shafts can not stand the force in blend door failure. That equals a blocked heater core and loss of heat. Start the Jeep® and turn on the AC. Manually switch between heat and AC by turning the axle left and right with your fingers. If there is no change repair kit is your solution.
How can I repair my Jeep Grand Cherokee heater?
The dealerships and auto repair centers do things “by the books” and they have plenty of reason to. Lots and lots of labor when done their way. pull off the entire dash, drain out the vehicles coolant, disconnect the heater core and disassemble all of the heater box. That’s a ton of work and flag hours. That adds up to big bucks for them.
What is code for Jeep Grand Cherokee heater blend door?
This method involves a little disassembly but is a great way to ensure our Jeep® Heater aluminum blend doors are the right solution for you. The code numbers will be displayed on the screen one at a time. 22 or 54 – Left temperature door is broken or 47 – motor not responding.
There is no electronic diagnosis available for your Jeep®. Physically check the operation of the blend doors by removing the glove box. Remove the blend door motor which is located to the side of the opening. The motor is held in place with two Phillips screws.