How to replace a timing belt on a 2005 Jetta?
2005 (aka 2005.5) 2006 VW Jetta TDI timing belt replacement (1.9L BRM engine) This DIY shows how to remove and install a new timing belt on a 2005 or 2006 VW Jetta TDI with cost of belt replacement parts Back to a5 Jetta turbodiesel FAQ list and “how to” index difficulty level: 3/5 Introduction
What should I do about my timing belt?
2004, 2005, VW Jetta TDI, and 2006 VW Golf TDI, New Beetle TDI timing belt removal and replacement procedure part 1- 1.9L bew engine Timing belt removal for 2004 or 2005 VW Jetta TDI and Golf/New beetle TDI 2004, 2005, or 2006
When to replace timing belt on New Beetle?
This article shows how to replace the BEW VW TDI engine timing belt found on Golf and New Beetle TDI 2004-2006 and VW Jetta TDI 2004-2005. The factory change interval is before every 100,000 miles with an inspection at 80,000 and 90,000 miles.
Where are the timing marks on a Golf Jetta Beetle?
The camshaft timing marks will have (2) tabs on the hub behind the cam sprocket that will need to be centered with the timing arrow on the timing belt backing cover. Install crankshaft locking tool T10050.
Why is my VW Jetta not shifting out of 2nd gear?
At about 110,000 miles it began to jerk when shifting from 1st to 2nd gear and 2nd to 3rd gear. At 120,000 it would not shift out of 2nd gear after about 20 continuous minutes of driving. I have been told that the cost to fix it is greater than the value of the car at this point and to get rid of it ASAP.
What kind of wrench do I need to replace timing belt?
The crankshaft pulley bolts are 10mm triple square. Almost all tensioners will need an allen wrench instead of the 2 pin spanner wrench. There is no need to remove the valve cover and there’s more room under the hood. If you have experience with ALH engine timing belts, this will be much easier.
What kind of bolt does a Jetta caliper use?
24.4 Mk3 – FRONT VW Caliper Mounting Bolts Type: Bolt 55.59 Type: Bolt 124.74 Mk3 – FRONT Girling Caliper Mounting Bracket Type: Bolt 24.4
Do you need to remove the valve cover when replacing the timing belt?
There is no need to remove the valve cover and there’s more room under the hood. If you have experience with ALH engine timing belts, this will be much easier. Before doing the timing belt, check your TDI engine for camshaft wear. If you have wear, I suggest fixing it before doing the timing belt so that you don’t have to redo the belt later.
Do you need a timing chain in a VW?
Some cars do not have a timing belt, though. Some Volkswagens, for example, have a timing chain instead. So what then is the distinction between timing belts and timing chains?
When to replace timing chain and gear set?
Since this service requires removal of the timing cover, it is recommended to replace all timing components, water pump, and front seals at the same time, unless they have been recently serviced. This is much more cost effective than returning for the same service after a partial service interval has elapsed.
What was the settlement with VW timing chain?
As the court fees piled up, Volkswagen agreed to settle 7 class-action lawsuits in one combined action in May of 2018. As part of the settlement, the following Volkswagen vehicles were given an extended “new vehicle limited warranty” to cover future repairs or replacements of the timing chains and tensioners.
Where are the timing marks on a VW?
Make sure that the camshaft and crankshaft timing marks are aligned. Install the timing belt, with the arrow pointing in the direction of rotation, on the crankshaft sprocket, the water pump sprocket and the camshaft sprocket. Install the lower and center timing belt covers.
Where are the timing marks on a 16 valve engine?
Slide the timing belt from the sprockets. Check the alignment of the timing marks. On 16-valve engines, the mark on the tooth should align with the mark on the rear belt cover. Install the new timing belt and tension the belt so it can be twisted 90° at the middle of it’s longest section, between the camshaft and intermediate sprockets.
Where is the timing belt on a 8 valve engine?
On 8 valve engines, the notch on the crankshaft pulley should align with the dot on the intermediate shaft sprocket. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt. Slide the timing belt from the sprockets.
When to change the timing belt on a VW Beetle?
When dealing with crucial timing belt service, err on the side of caution and change your VW Beetle timing belt every 75,000 miles. It is our recommendation to closely inspect all timing belt components before the recommended interval.
How often do timing belts need to be replaced?
But more often than not, you will need to do VW Jetta timing belt replacement sooner or later. Timing belts in VW Jettas aren’t built to last forever and will give out on you eventually. In general, a VW Jetta timing belt will usually hang around for somewhere between 60,000 and 100,000 miles before needing to be replaced.
How to replace timing belt on Audi 1.8 turbo engine?
This video describes how to replace a timing belt on a VW 1.8 Turbo engine using a 2002 VW GTI as an example. This engine is common to many VW and Audi models. The methods demonstrated in this video can be used both on this engine as well as being applied as appropriate to other timing belt installations. Loading…