How to get the trouble codes on a Harley Davidson?

The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.

How to get the ECM code on a Harley Davidson?

The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run. 2- Push odometer resetbutton in & hold. 3- Turnignition switchto Ignition and release the odometer reset button.

How to know if your Harley has a V inerr code?

You may have a failing sensor on your throttle body. Look for one or more stored codes in your speedo head. A stored code should lead you in the right direction. If you do not have any stored codes; check for an intake leak. Hi, do you know what mean “V INERR” code? Hi, Andre. We would be happy to assist you; we just need some more information.

What does code 56 mean on a Harley Davidson?

Hi, Denver. Code 56 is-Crank Position Sensor/Cam Position Sensor Signal Error 41 is a ranking # and indicates check engine light open/low. These do not have anything to do with poor idle. 1st make sure that your intake is correctly sealed. Very common problem with your Magnetti Marelli assembly is the IAC sensor.

What are the 131 / 151 codes on a Harley Dyna?

This is the exerp from the 2008 Harley Dyna Service Manual that talks about the 131/151 codes. You will note that they tell you to “clear and ignore” the codes. Their reference is primarily associated with break-in, but it seems strange that something that is acceptable at 999 miles because an issue at 1001 miles.

What are the p0131 and p0151 codes?

The codes are specifically listed as P0131 and P0151 codes. The description in the Service Manual is: P0131 Front O2 sensor low or engine running lean P0151 Rear O2 sensor low or engine running lean The key point to look at here is “O2 sensor low” when analyzing what is happening with the IED’s in place.

How to get a diagnostic code for a Harley Davidson?

Is there a diagnostic code for fuel Moto?

Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run.

Where is the Diag switch on a Harley Davidson?

The trip odometer trigger switch is located in the left hand control module. The switch signal is sent to the speedometer over the CAN bus. If there is a problem with the CAN bus, the odometer self-diagnostic mode may not function. 1. Release the trip odometer trigger switch. “diag” will appear on odometer display.

What to do if your bike has an error code?

Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module. 10 – Turn Ignition switch to OFF.

How to troubleshoot an ICM error code on a Harley?

Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release the odometer reset button.

How to check low fuel on a Harley Davidson?

3- Turn ignition switch to Ignition and release the odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.

What does diag mean on a Harley Davidson?

How to choose the best Harley Davidson engine?

1. Primary application: Is the bike going to be used for all around street riding or is the goal to have an engine which is running at the maximum torque and horse power for track or drag racing? 2. Type of riding: Do you spend a lot of your time riding two up on highway trips or is it more important to have the most power you can get.

Where does the heat go in a Harley Davidson engine?

The engine transfers heat to the oil, which then goes through the oil cooler. The cooled oil now goes back into the engine to cool it, and the cycle repeats. Oil-cooling allowed Harley-Davidson to continue using the air-cooled Big Twin engine on its bikes.

Why is my Harley Davidson running so hot?

With the engines getting bigger, bikes becoming heavier, fuel emissions getting stricter, ambient air heat increasing coming off the pavement, traffic becoming busier causing more stop n go, no matter where you live or ride. All of this creates more heat.

When to shut down a Harley Davidson engine?

When my front engine cylinder hits that number the engine is overheating. I need to get the bike moving soon. If I can’t, I need to shut it down especially if the entire engine/trans/primary is cooking. Once those parts are at the same temperature as the engine case, they can no longer sink heat and a point of equilibrium is reached..

What happens to a Harley Davidson engine in traffic?

Slow moving your bike and stand-stills will ruin a good engine. The traveling at idle speeds in stop-n-go traffic is not the way the harley is designed and nothing short of a 20 mile an hour breeze would improve that situation much. HEAT is the killer of the air-cooled engine.

What does no RSP mean on a Harley Davidson?

On models not equipped with a tachometer “No Rsp” will appear when the tachometer identifier is selected. “No Rsp” (no response) will also appear if the run/off switch is in the off position when doing this procedure.

What was the fault code for FLHX in 2008?

2008 flhx fault codes p1510 limited performance module, p2138 TGS correlation error (twist grip sensor) these faults come up intermitantly, any suggestions? Clicking this will make more experts see the question and we will remind you when it gets answered.

What is the diagnostic code for a 2007 Harley Davidson?

2007 Harley Davidson Diagnostic Trouble Codes (from Service Manual 99497-07) Getting Codes: 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold. 3- Turn ignition switch to Ignition and release odometer reset button.

What is the EFI code for a Harley Davidson?

P2138 TGS Correlation Error (Twist grip sensor) 27. P0120 TPS1 Range Error 28. P0220 TPS2 Range Error 29. P0122 TPS1 Low 30. P0123 TPS2 High/Open 31. P0222 TPS2 Low 32. P0223 TPS2 High/Open 33. P2135 TPS Correlation Error 34.

What to do if you get an error code on your Harley Davidson?

Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTCs again by repeating steps 1 to 9. If the code is current it will reappear. Press and release the odometer reset button to continue to the next module. Turn Ignition switch to OFF.

What does the Code 02 mean on a Harley Davidson?

If it were a current code, the light would remain lit while running. Above codes can also be set if 02 sensor fails. CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.

3- Turn ignition switch to Ignition and release odometer reset button. Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.

What are the diagnostic codes for a speedometer?

Is there a trouble code on the speedometer?

Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Trouble codes are read via the odometer.

How to check your Harley Davidson for problems?

Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.

Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” will then appear.

How to diagnose a Harley Davidson system problem?

To diagnose Harley Davidson system problems, begin by observing the behavior of the check engine lamp. When the ignition switch is turned ON, the check engine lamp will illuminate for approximately four seconds and then turn off. If the check engine lamp is not illuminated at key ON or if it fails to turn OFF after the initial four second period.

Navigation