How do you use Interlux Brightside paint?
Apply 2-3 coats of Brightside, allowing a minimum of 16 hours between coats. Sand between coats with 320-grit sandpaper. Note: Avoid applying late in the day as condensation can cause loss of gloss overnight. In warm or windy conditions, up to 10% Interlux Brushing Liquid 333 may be added to ease application.
How long does it take for Interlux Brightside to cure?
8 to 16 Hours
Cure Time: 8 to 16 Hours to Overcoat.
What is Interlux paint?
Interlux Ultra w/ Biolux Hard Antifouling Paint Interlux Ultra with Biolux is an antifouling paint specially formulated for long-term protection in high fouling water.
What is topside paint?
A topside paint is any paint you apply above the waterline anywhere on your boat. This includes the sides of the hull, deck, and interiors. Marine topside paints are commonly one of the following types: one-part polyurethane, two-part polyurethane, and alkyd marine enamel.
Can you wet sand Interlux Brightside?
I have two coats of Interlux Brightsides paint on the outside of my Sassafras, and I’m getting some orange peel after each coat. I can very gently wet sand it smooth-ish with 600 grit sandpaper, and it is smooth, but a dull finish…
What is Interlux Brushing Liquid 333?
Interlux 333 Brushing Liquid Solvent is a slow drying solvent used to ease brushing and facilitate the flow of specified paint coatings. 333 extends paint drying time in hot weather and is also recommended in various topside systems for removing sanding residue from fiberglass and wood surfaces.
How long does it take boat paint to dry?
No sanding is required between coats. Allow to dry 24 hours for light use and 3 days for full use.
Who owns Interlux paint?
AkzoNobel
A division of AkzoNobel, Interlux® is one of the world’s largest manufacturers of high performance boat paint, yacht coatings and marine protection.
Can you tint topside paint?
TotalBoat Wet Edge topside paint can only be tinted by mixing it with other colors of Wet Edge. Universal pigments, pigment dispersions for epoxy and polyester resins, and other hardware store grade tints should never be mixed into TotalBoat Wet Edge.
Can you buff Interlux paint?
Do not sand or buff Interlux Perfection if it’s cured more than 2 days at 73 degrees. Interlux gives max times for sanding: “Apply 2-3 coats of Perfection (depending on color) following the proper dry times. Perfection may be applied by roller and brush using the roll and tip method.
What is interlux?
A division of AkzoNobel, Interlux® is one of the world’s largest manufacturers of high performance boat paint, yacht coatings and marine protection. For over a century, Interlux has been creating the most innovative coating solutions to protect, beautify and improve the performance of all types of boats.
Does polyurethane go bad?
Gloss oil-based varnish, polyurethane and Danish oil can last 10 or 20 years, though satin finishes and stains may fail sooner as pigments and flattening agents disable the driers. Water-based coatings and paints can also be viable longer than three years. Shellac , though, can go bad in under a year.
What is the best water based polyurethane?
The Minwax Water Based Oil-Modified Polyurethane is the best polyurethane because its great for anything you need to coat around your home. Its water based so it produces less fumes and cleans up easily with warm water.
Is polyurethane clear finishes for exterior use?
Because polyurethane is a clear finish , it can bring out the beauty of wood. A popular choice for cabinets and trim, it also protects wood. Exterior polyurethane contains polyurethane resin, a flatting agent that reduces the gloss, ultraviolet absorber and solvent. Most polyurethanes rated for exterior use will be oil based.
Can I spray poly?
Set Up Your Sprayer Choose the right tip Adjust the volume control so you can apply a perfect layer. The experts say that you should spray the poly on and on each third stroke you should overlap the poly slightly. Pour the poly in the sprayer Thin the poly if the manufacturer suggestions recommend that you do so