How do you replace a transmission conductor plate?

How do you replace a transmission conductor plate?

PART 2: Kent walks you through the steps of carefully removing the valve body from the transmission, placing it on the bench and removing the old conductor plate, inspecting it for damage, and properly installing the new conductor plate onto the valve body.

Can a Mercedes 722.9 transmission control plate be repaired?

This is a repair service for your existing 2004+ Mechatronic Mercedes Benz 722.9 Transmission Control Module (TCM) Conductor Plate or VGS that eliminates the need for any programming or SCN coding on vehicles that utilize the 7 speed transmission (7G Tronic).

What causes a failed mechatronics Transmission Control Module conductor plate?

Symptoms of a failed mechatronics transmission control module conductor plate can cause the vehicle to enter into limp mode and will also cause the following error codes – our repair service will only correct the following error codes: False diagnostic codes for the Output Speed Sensor can be caused by faulty wheel speed sensors.

How to repair a transmission pan and gasket?

This procedure has to be done on a VERY CLEAN workbench and special care must be taken to avoid any dirt particles from getting on the valve body or conductor plate. No specific instructions are included for removing the transmission pan and old gasket. A new filter and gasket should ALWAYS be installed ( see related products below )

PART 2: Kent walks you through the steps of carefully removing the valve body from the transmission, placing it on the bench and removing the old conductor plate, inspecting it for damage, and properly installing the new conductor plate onto the valve body.

Do you need to replace the conductor plate on a Mercedes 722.9?

Luckily, the transmission does not need to be removed in order for you to replace the conductor plate. The early 722.9 transmission (MY 2004-2007) identified as VGS1 on top of the TCU required that you replace both the valve body and conductor plate.

Do you need valve body and conductor plate replaced?

The majority of these transmissions were identified as VGS1 and required the replacement of both the valve body and conductor plate. Unfortunately, Mercedes-Benz declined to sell replacement valve bodies to independent repair shops claiming that these components were related to the security of the vehicle. Yet they will sell complete transmissions.

Symptoms of a failed mechatronics transmission control module conductor plate can cause the vehicle to enter into limp mode and will also cause the following error codes – our repair service will only correct the following error codes: False diagnostic codes for the Output Speed Sensor can be caused by faulty wheel speed sensors.

How does the conductor plate work in a car?

The conductor plate transmits the signals to the valves from the control module. The sensors mounted on the plate are crucial to the operation of the automatic transmission. If the sensors fail, the transmission control unit will be unable to determine which gear to engage the transmission in.

Why is my Mercedes transmission conductor plate cracked?

My conductor plate was the culprit with little cracks and this kit did the job of replacing that. I still had to clear the trans code at a local mercedes indy before full function was realized

How to change conductor plate on Mercedes 722.6 5G transmission?

Instructions on how to change the conductor plate and valve body on Mercedes-Benz 722.6 5G transmission. Allow the car to cool down. Raise your car using a car lift, ramps, or jack stands. Secure the vehicle with jack stands. Set parking brakes.

How long does it take to replace a transmission conductor plate?

The replacement took about 3 hrs to do. I took my time to keep track of all the parts and the order of removal. I found example online by searching conductor plate and e320. There are step by step guides on how to do this job yourself. This is the 2nd job I’ve done on this transmission. Last job I had to fix the broken speed regulator spring.

What is the conductor plate on a Mercedes Benz?

The Conductor Plate is a component of the transmission that eventually will malfunction as the vehicle ages.

What causes the conductor plate to malfunction?

The Conductor Plate is a component of the transmission that eventually will malfunction as the vehicle ages. Sometimes the speed sensor built within the Conductor Plate fails causing erratic shifting, in other cases the float may fail causing…

My conductor plate was the culprit with little cracks and this kit did the job of replacing that. I still had to clear the trans code at a local mercedes indy before full function was realized