How do you remove the serpentine belt on a Toyota Camry?
There are two 10mm bolts that need to be removed. Figure 2. Inner fender liner removal. Label and save your bolts so you know where they go during re-installation. Remove the serpentine belt by turning the 19mm bolt on the tensioner clockwise.
How do you jack up a Toyota Camry?
Lift the front of the Camry on its frame and remove the wheels. This will give you access to the belt tensioner pulley. Figure 1. Lift and secure front of vehicle. Use a jack stand to make it safer when you are working in the fender well. (Related Article: How to Jack Up Your Car – CamryForums.com)
How do you remove a water pump from a Toyota Camry?
Remove the water pump pulley by wedging a pry bar behind the pulley and removing the four 12mm bolts. Remove the four 10mm bolts and two nuts that hold the water pump fastener in place. Spray down the area with brake cleaner. Place a drain pan underneath and remove the water pump with a pry bar.
When do you need to loosen a tensioner pulley?
Sometimes, maintenance or repair will require tightening or loosening a tensioner pulley. Replacing a drive belt or timing belt, for example, would require you to loosen a tensioner pulley to make room for the new belt, as the new belt is smaller than the worn drive belt.
How do you loosen a belt tensioner on a car?
Use a ratchet and socket and turn the bracket bolts counterclockwise to loosen and remove the bolts from the belt tensioner bracket. Now, you can pull the belt tensioner straight off the engine block. Make sure that the belt stays seated inside of all of the pulleys while loosening the belt tensioner.
What do you need to replace timing belt on Toyota Camry?
Some things to note on the 1MZFE engine are: A 10mm stud holds the water pump to the block on this engine. A stud removal tool can be used, otherwise the camshaft sprockets and timing belt cover will need to be removed first. The tensioner will apply tension to the belt as the tesnioner bolts are tightened.
There are two 10mm bolts that need to be removed. Figure 2. Inner fender liner removal. Label and save your bolts so you know where they go during re-installation. Remove the serpentine belt by turning the 19mm bolt on the tensioner clockwise.
Can a tensioner be replaced on a drive belt?
The bolt on the tensioner pulley is the one used to move the tensioner, to remove tension on the drive belt for removal. My plane is to replace the drive belt, the tensioner pulley, and the No. 1 and No. 2 idler pulleys.
Some things to note on the 1MZFE engine are: A 10mm stud holds the water pump to the block on this engine. A stud removal tool can be used, otherwise the camshaft sprockets and timing belt cover will need to be removed first. The tensioner will apply tension to the belt as the tesnioner bolts are tightened.
How can I relieve the tension on my belt?
Rotate the pulley on the belt tensioner counterclockwise to relieve the tension of the belt with the proper sized socket and ratchet. Slide the belt off of the belt tensioner pulley. Let the belt hang down.
How do you install a new engine belt?
Slip the belt off the remaining pulleys and out of the engine compartment. Install the new belt by wrapping it around the pulleys according to the routing guide. Begin with the crankshaft pulley, the lowest pulley at the bottom front of the engine, and end with the alternator pulley.
How do you tighten a serpentine belt on a car?
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.
What kind of pulley does a serpentine belt use?
Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times.
Where do I find the serpentine belt on my car?
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
What happens if the drive belt breaks on a 1999 Toyota Camry?
If the belt breaks, all of the accessories will stop functioning. Raise the hood on the 1999 Toyota Camry and prop it open. Locate the belt routing diagram that is stamped to the left side of the fan cover. Refer to the diagram when installing the new drive belt.
What kind of accessories does a 1999 Toyota Camry have?
The front engine accessories on the 1999 Toyota Camry include the power steering pump, the alternator, the water pump and the air conditioner compressor. A single drive belt (also called a serpentine belt) controls these accessories. When the engine is running, the belt is driven around each pulley by the crankshaft.
How do you change a drive belt on a 1999 Toyota Camry?
Raise the hood on the 1999 Toyota Camry and prop it open. Locate the belt routing diagram that is stamped to the left side of the fan cover. Refer to the diagram when installing the new drive belt. Locate the self-adjusting belt tensioner on the front center of the engine above the crankshaft pulley.
Where is the belt tensioner on a Toyota Camry?
Locate the self-adjusting belt tensioner on the front center of the engine above the crankshaft pulley. The tensioner has a roller pulley attached to the bottom arm of the tensioner. Turn the tensioner from the bolt head that connects the roller pulley to the tensioner arm. Slide the socket and breaker bar onto the pulley bolt head.
What’s the best way to replace a serpentine belt?
Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.
The front engine accessories on the 1999 Toyota Camry include the power steering pump, the alternator, the water pump and the air conditioner compressor. A single drive belt (also called a serpentine belt) controls these accessories. When the engine is running, the belt is driven around each pulley by the crankshaft.
What causes a serpentine belt pulley to squeak?
The serpentine belt in your car powers the accessories such as air conditioning, power steering, the alternator, and waterpump. Tensioner pulley wear will cause your pulley to squeak.
What does the serpentine belt on a Toyota do?
Toyota or Lexus with a V6 engine. The serpentine belts are responsible for driving accessories off of the crank of the engine. In the Toyota V6 engines, they drive the alternator and A/C compressor on one belt, and the power steering pump on the secondary belt.
Lift the front of the Camry on its frame and remove the wheels. This will give you access to the belt tensioner pulley. Figure 1. Lift and secure front of vehicle. Use a jack stand to make it safer when you are working in the fender well. (Related Article: How to Jack Up Your Car – CamryForums.com)
How big is a CTA tools belt tensioner socket?
CTA Tools 2717 Toyota Belt Tensioner Socket is designed with a special configuration with 6 internal slots that service 2000 and up Toyotas. Use with 1/2-Inch square or 7/8-Inch hex drive tools.
What kind of tool set is serpentine belt tensioner?
Serpentine Belt Tool Set with Locking Flex Head Ratcheting Wrench – 89000 GEARWRENCH 5 Pc. 3/8″ Drive 6 Pt. Magnetic Swivel Spark Plug Socket Set, 80601 Amazon Business : For business-only pricing, quantity discounts and FREE Shipping. Register a free business account Have a question? There was a problem completing your request.
Is the tensioner pulley on a 2003 Toyota Corolla Le?
Great addition to my toolbox, but this does not fit the tensioner pulley bolt on a 2003 Corolla LE. The bolt on my car required a slim line Torx bit (T50) in order to get into the tight space. I guess Toyota used different bolts on this pulley throughout the production years. Good tool, but couldn’t use. Too thick.
What does the pulley on a belt tensioner do?
The pulley is what allows the movement of the drive belt. The spring keeps the drive belt in its correct tension. The tensioner arm is a mechanism that allows for the adjustment or the removal of the drive belt. It delivers enough slack on the drive belt for easier adjustments. The base is what holds all the different parts together.
Is there a drive belt tensioner for a 2008 Sienna?
2008 (2GR-FE) drive belt tensioner – replace pulley only? We have a 2008 Sienna with the 3.5l 2GR-FE V6, with 195,000 miles. Lately we have a chirping noise under the hood, in the area of the drive belt tensioner and the No. 2 (right) idler pulley.
https://www.youtube.com/watch?v=gfSJvN-CE2E
Where is the tensioner on a Toyota Camry?
Replacing the entire tensioner will obviously be a more expensive proposition, but also a straightforward one. Figure 1. A 2007 Toyota Camry 2.4L I4 engine (the drive belt and tensioner is under the engine mount on the left). Belt removal tool or equivalent (long 3/8″ breaker bar with 90-degree tip, two box wrenches, etc.)
When did Toyota Camry stop using drive belt?
Eliminating an accessory that requires drive belt connection also significantly shortens belt length. For this reason, the 2.5L I4 introduced in 2010 included electric power steering (EPS), thus eliminating a belt connection to a vane pump (the hybrid version of the 2.4L engine always used EPS).
Why does my Toyota Camry make a squealing noise?
Most engine squeals are the results of a worn out belt, idler, or tensioner pulley. Due to hundreds of heat cycles and wear on the rubber belt as well as bearings in the pulleys, the annoying noises you hear arise.
How much does it cost to repair a Toyota Camry?
We’ve also included the average cost of repair by a mechanic for each part. These examples are based on a 2010 Toyota Camry with the 3.5L V6. OEM Part Cost Only: Approximately $50-$60 per belt. The serpentine belt, also called the drive belt, turns the pulleys on your engine accessories.
How do you remove serpentine belt from tensioner?
Remove the serpentine belt from the pulleys and return the tensioner to its home position. Install a new belt on all the pulleys, leaving it off the tensioner for now. Turn the tensioner counterclockwise again with your socket and ratchet and slide the belt onto the tensioner idler pulley.
How many miles does a serpentine belt last?
The serpentine belt, also called the drive belt, turns the pulleys on your engine accessories. This is vital to keep the alternator, power steering pump, and air conditioning functioning. Serpentine belts don’t wear quickly, and under ideal conditions, they should last up to 100,000 miles.