How do you remove a Porsche Carrera door panel?
To remove or replace the window switches you will need to remove the door panel. (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal). Once the panel is off, you can remove the window switch by first disconnecting the wiring. Squeeze the tap (red arrow) and pull straight back.
How to remove rear panel access to AC unit?
If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: Hm4dQMoPPeB3pbce)
How to remove the back panel of a Ford Expedition?
Ford Expedition – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: Hm4dQMoPPeB3pbce)
How to replace the regulator on a Porsche Carrera?
The first step in replacing either the regulator or the power window motor is to remove the door panel (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal ). Make sure that you eliminate the power window switch as a potential problem before you start tearing into your door.
To remove or replace the window switches you will need to remove the door panel. (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal). Once the panel is off, you can remove the window switch by first disconnecting the wiring. Squeeze the tap (red arrow) and pull straight back.
How to remove a stuck power window in a car?
Disconnect the two plastic wire switches: You can use a flat-head screwdriver to pull the connectors apart. Put the door console aside. Remove the door panel: Using your hands or a flat-head screwdriver, gently start at the front edge of panel and pry it off.
How do you replace a garage door handle?
You can tie off the wires to the door—do not reconnect them since you’re not going to use the window. Replace the polyethylene cover. Put the door panel back. This is a multistep process: start by inserting the door handle into the panel and fit the top-rear edge of the door panel into the top lip of the door frame.
What to do if rear left door does not open?
Firstly I removed the plastic cap behind the door opener and removed the torx screw behind it. The next bit to remove is the plastic cap on the internal door handle (the bit you you pull to close the door). it is around 19cm long. twist this this up and it should pop off
Can a broken window regulator be replaced in a Carrera?
Having a broken window regulator can surely put a damper on that. The first step in replacing either the regulator or the power window motor is to remove the door panel (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal ).
Why does the inner door cover not come off?
The central locking sounds as if it is working so it is probably a linkage issue. My question is – Can anyone tell me the best way to remove the inner door cover. I have removed 2 screws at the “handle” and another at the door opening lever but it is still solidly held on.
The first step in replacing either the regulator or the power window motor is to remove the door panel (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal ). Make sure that you eliminate the power window switch as a potential problem before you start tearing into your door.
How to remove the engine from a Porsche 911 Carrera?
(Pictures 38 and 39) Open the engine decklid and remove the airbox. Begin by loosening the hose clamp holding the boot to the throttle body (green arrow), then squeeze the tabs on the MAF connector to release it (yellow arrow). Now open the two harness holder clips (purple arrows). Remove the oil filler tube from its clip (blue arrow).
How to adjust window height in Porsche Carrera?
E: Adjust the window height by removing the outer plugs in the bottom of the door and using an E6 Torx socket to turn the stopper (counterclockwise = higher window). F: Check the window rake angle by placing a sheet of paper in the window and rolling it up.
What to do about a broken door handle on a Porsche Carrera?
The 911 Carrera door handles and door lock mechanism take a lot of use and abuse over the years and can experience many different failures. The first step in fixing any door lock or handle problems is to remove the door panel (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal ).
Can you remove the door panel on a Porsche 996?
For details on removing the door panel, see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal. On the 996, when you have the door panel removed, you can view the regulator. The 997 have an inner panel so you will have to watch the actual window.
How to replace the window switch on a Porsche Carrera?
To remove or replace the window switches you will need to remove the door panel. (see Pelican Technical Article: Porsche 911 Carrera Door Panel Removal ). Once the panel is off, you can remove the window switch by first disconnecting the wiring. Squeeze the tap (red arrow) and pull straight back.
(Pictures 38 and 39) Open the engine decklid and remove the airbox. Begin by loosening the hose clamp holding the boot to the throttle body (green arrow), then squeeze the tabs on the MAF connector to release it (yellow arrow). Now open the two harness holder clips (purple arrows). Remove the oil filler tube from its clip (blue arrow).