Why is my turn signal not working on my Harley?
You may have a bad module or corroded/bad connections at the module or at the handlebar switch harness/ plug. If you determine that you need a turn signal module, we suggest Badlands. I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm.
What are the turnsignals on a Harley Davidson?
1) Turnsignals all stock means the front signal lights one of the two filaments in the front; the rear signal lights use single filiament lights.
Why are the turn signals on my hog not flashing?
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
Why is my left turn signal not flashing?
When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.
Why are the turn signals on my Harley not working?
2) If you have LED type bulbs, someone replaced the turnsignals BEFORE you and may not have added the recommended load equilizer (simulates load of filament type bulbs), and never got the problem fixed just right, and if left alone it can “fry” the TSM/TSSM. Hopefully you have not gotton to this point and have to replace the module.
Why is my hazard light not working on my Harley?
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
1) Turnsignals all stock means the front signal lights one of the two filaments in the front; the rear signal lights use single filiament lights.
Where does the flasher go on a Harley Davidson?
Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad.
These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code. Accessing the diagnostics menu requires you to press several of the accessory switches in a very specific manner, within a short amount of time.
Why is my horn not working on my Harley?
I do not think you have a horn relay, so very little to go wrong. Common problem is blown fuse or horn is temperature sensitive, as it is simply a electromagnet with bimetallic strip interrupter that makes and breaks rapidly the magnetic field buzzing the metal diaphram.
Why is my turn signal on on my Dyna Glide?
Diagnosing and clearing the codes on each module is really simple, as explained below. Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse.
Where is the horn on a Harley Davidson Fat Boy?
Traced the ground lead coming off the horn which, on an ’02 Fat Boy mounts on top of the horn/choke bracket by the front head. Not only was the bolt backed out, but it was missing entirely? Found it sitting on the bottom of the engine case. Re-installed it and the horn works just fine now. Click to expand…
You may have a bad module or corroded/bad connections at the module or at the handlebar switch harness/ plug. If you determine that you need a turn signal module, we suggest Badlands. I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm.
Do you need to reset the ECM on a Harley Davidson?
This computer controls the fuel-air mixture and ignition, as well as other things. If you’ve taken any component off, modified the Harley, or need to get out of the “limp mode,” you’ll need to reset the ECM, but the process is always the same.
Where is the reset button on a Harley Davidson?
Before you start the reset procedure, be sure your run/stop switch is turned on. The run/stop switch is located on the right side of your handlebar. Turn it to run, then proceed. Figure 1. Run/stop switch. With the run/stop switch on, turn the ignition on and then off three times.
Where is the run / stop switch on a Harley Davidson?
The run/stop switch is located on the right side of your handlebar. Turn it to run, then proceed. Figure 1. Run/stop switch. With the run/stop switch on, turn the ignition on and then off three times. Don’t do it too quickly; in fact, it’s best you leave a second or two in between: turn it on, wait, off, wait, on, wait, off, wait on, wait, off.
Can a Dyna turn signal module go out?
I have a ’91 Dyna, and yes, I had the module go out on me. On inspection, it looked partially melted or burned. But before you go spend about a hundred dollars (HD, get it!!), make sure that both bulbs on that side are OK. When one bulb goes, the indicator and the other bulb should stay on steady when you try that side turn signal.
Why does my badlander turn signal not flash?
Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly. If bike is moving, if you press the right turn signal, it will light up, but not flash. Looked in the service manual and this problem is not listed for troubleshooting the turn signals.
How big are the turn signals on a Harley?
COWONE 3 1/4 Inch Led Turn Signals Front 1157 Turn Signal LED Running Lights for Harley Motorcycle Road Glide Road King Softail Ultra Classic Ultra Limited Electra Glide… . . Only 8 left in stock – order soon.
Why is my Harley Davidson Ultra Classic not starting?
I have a 2010 ultra classic with ABS. It is not starting. The battery voltage is 12.75 off the battery. When I turn the main switch on, I get a drop to 12.5, and when the kill switch is turned on, I get a drop to 12.38. The self test goes out and hit the start switch with nothing – no volt drop, no starter engage, no nothing. DEAD.
I have a ’91 Dyna, and yes, I had the module go out on me. On inspection, it looked partially melted or burned. But before you go spend about a hundred dollars (HD, get it!!), make sure that both bulbs on that side are OK. When one bulb goes, the indicator and the other bulb should stay on steady when you try that side turn signal.
What should I do if my turn signal is not working?
The obvious first. You have checked/replaced the turn signal bulbs/lights, right? Take them out, inspect them, clean the socket, clean the base of the lamp and replace, at least. Have you tried this procedure?