Why is my power window not working on my Tacoma?
I have a 2004 Xtra Cab Tacoma. I’ve changed both power window switches and the motor is good when I wire it directly to a battery. ANY idea as to why my passenger side will roll down with the passenger side switch and not the driver’s side…neither will roll the window up. OCCASIONALLY, they will both work. I’m thinking a bad ground somewhere?
What kind of window regulator does Toyota Tacoma have?
450741799 1995-2004 Toyota Tacoma Front Left Window Regulator with Motor and reg $79.31 and free shipping. It’s worked perfectly…. I am having this same exact problem.
Where is the passenger side switch on a Tacoma?
The passenger side switch, for the passenger side window, are those copper and silver circular contacts in the upper right of the bottom pic. The driver’s side switch for the driver’s side window are those thin copper and silver blades that run vertically in the lower right of the bottom picture.
Is the driver’s side power window going up or down?
I have a 2001 Double-Cab Tacoma. The driver’s side power window has started acting up recently. It goes down fine, at a normal rate. When I try to make it go up immediately, it won’t go up. If I wait a minute or so, I can try again and it will go up an inch or two, then it stops.
https://www.youtube.com/watch?v=64bw9AXoJ3o
For the same reason, it can’t be the wiring from the master switch to the door switch, nor the LR window motor. It can’t be the wiring from + 12 VDC to the left rear switch because the left rear door switch can lower the window. The right rear is more difficult.
What should I do if my Toyota power window broke?
Check for proper operation of the “one–touch open and close” function by fully pushing the switch briefly to the “DOWN” and “UP” positions. At this time the power window switch for the passenger’s door window should be blinking. 4. Push down and hold the passenger’s door power window switch to completely open the window. 5.
How do you reset the auto window on a Toyota?
1. Push the auto down button and hold it at the bottom for a few seconds, 2. Push the auto up button and hold it at the top for a few seconds.
How can I tell if my power window is bad?
Measure the voltage between the two terminals on the plug while you push DOWN on the door switch. If 12 VDC, the motor is bad. If not, the problem is the master switch, the wiring between the master switch and the door switch, or the wiring between the door switch and the motor.
What happens when you open a Tacoma door?
Every time you open and close your door, all the wires get flexed. I’m not aware of an issue with Tacomas, but have heard of other makes getting cracked wires in that area. The insulation may be intact, but the copper inside can be broken.
What are the symptoms of a bad power window switch?
If you suspect your power window switch is going bad or failing, watch for the following symptoms: 1. All the windows quit working If all of the windows quit working at once, meaning there is no response when you push the power window switch, chances are there is a loss of power in the electrical system.
Why does my Toyota Tacoma shudder when driving?
In order to understand this issue, we went to a local Toyota dealer and took a Tacoma out for a few hours. We drove highways and streets, up hill and down. The truck performed admirably except when driving 15-25 mph through different school zones or up hill. The fact is that it shuddered through the seat and a little on the steering wheel.
What’s the problem with my Toyota Tacoma drive shaft?
Owners like those on Toyota Tacoma forums like Tacomaworld.com say the issue is about angles and the two-piece drive shaft. There are many owners who have decided to address the issue on their own and work out their own fixes. One of the common fixes deals with inserting shims to change this angle.
Why is the blower on my Toyota Tacoma turning brown?
The blower wire pigtail that plugs into the resistor block has a loose connection. Toyota sells the pigtail replacement. Don’t remember the cost or part number. Follow the wiring that enters the blower motor resistor block the white wire is main supplied power I’d bet it’s turned brown about 1 inch to 1/2 an inch all the way to the connector.