Why does my temperature gauge read hot and cold?
If it reads approx. 140 Ohm (or more) when the engine is both cold and hot then the sensor is faulty and needs to be replaced. If the sensor reads 30-50 Ohms when the engine is hot then there may be a problem with the wiring back to the gauge or with the gauge itself.
What should I do if my temperature gauge reads 50 ohms?
If the sensor reads 30-50 Ohms when the engine is hot then there may be a problem with the wiring back to the gauge or with the gauge itself. Make sure the engine is turned OFF and that the vehicle’s ignition key is in your pocket when you test the sensor. Also don’t burn yourself on the engine block when the engine is hot Was this answer helpful?
What should the resistance be on a cold engine?
With a cold engine the resistance should be approx 140 Ohms. With a hot engine it should measure 30-50 Ohms. If it reads approx. 140 Ohm (or more) when the engine is both cold and hot then the sensor is faulty and needs to be replaced.
How to test the temperature of an engine?
To test the sending unit, disconnect the single wire black connector and using a DMM (Digital Multimeter – Ohmmeter function) measure the resistance between the sending unit terminal and earth (or ground – the engine block will be earthed). With a cold engine the resistance should be approx 140 Ohms.
If it reads approx. 140 Ohm (or more) when the engine is both cold and hot then the sensor is faulty and needs to be replaced. If the sensor reads 30-50 Ohms when the engine is hot then there may be a problem with the wiring back to the gauge or with the gauge itself.
How can I tell if my coolant temperature sensor is bad?
To diagnose the coolant temperature sensor, you need a repair manual for your car model to find what measurement values you should expect from the coolant temperature sensor. Connect an OBD2 Scanner and look for related trouble codes. Check the live data to see the temperature from the sensor.
If the sensor reads 30-50 Ohms when the engine is hot then there may be a problem with the wiring back to the gauge or with the gauge itself. Make sure the engine is turned OFF and that the vehicle’s ignition key is in your pocket when you test the sensor. Also don’t burn yourself on the engine block when the engine is hot Was this answer helpful?
What should coolant temp be when engine is hot?
With a good OBD2 code reader, you can also check the live data and the parameters of the CTS sensor. Check that the temperature value of the CTS is around 80-90c when the engine is hot. A lot of engine coolant temperature sensors have two wires and the sensor is controlled by Ohm.
What causes a car temperature gauge to stay on low?
What could cause the temperature gauge to stay on low? The most common causes of why the temperature gauge stays on cold are faulty coolant temp sensor, faulty temperature gauge, broken wires, bad thermostat , and air pockets in the cooling system.
Why is my engine temperature reading so cold?
The most common problem when it comes to a faulty engine temperature reading is the coolant temperature sensor itself which is sending the information to the cluster.
Why does the temperature gauge stay on cold?
Air in the coolant system can also cause the temperature gauge to stay on cold if there is an air bubble right at the sensor spot. This can also often be indicated with a fluctuating coolant temperature gauge. If you suspect air in the coolant system, you have to bleed your coolant system with a unique technique.
What should I do if my temperature gauge starts to rise?
Start off and head toward a highway. Have the heat on HI, with the fan just enough ON so you can feel it. Then watch your gauge and air temp as the car warms up. the air should get warm in just a minute, before the gauge starts to rise. The, as the gauge rises, the heat will stabilize at HOT. then, if the gauge falls, what happens to the air temp?
Why does my temperature gauge read 30-50 ohms?
If the sensor reads 30-50 Ohms when the engine is hot then there may be a problem with the wiring back to the gauge or with the gauge itself. Make sure the engine is turned OFF and that the vehicle’s ignition key is in your pocket when you test the sensor.
What should the temperature gauge read when the engine is hot?
With a hot engine it should measure 30-50 Ohms. If it reads approx. 140 Ohm (or more) when the engine is both cold and hot then the sensor is faulty and needs to be replaced. If the sensor reads 30-50 Ohms when the engine is hot then there may be a problem with the wiring back to the gauge or with the gauge itself.