Why does my Kia Sedona have a check engine light?
Kia Check Engine Light (CEL) (also known as Service Engine Soon SES or MIL) may sometimes turn on and stay on when driving. This problem can effect Kia models such as: Sedona and other models.
What does the maintenance required light mean on a Kia?
The maintenance required light is simply indicating that the car is due for an oil change or other routine servicing. Your Check Engine light will either be orange, yellow, or red, depending on the manufacturer, and it will either be the words ‘CHECK ENGINE’ or it will be shaped as an engine.
How can I reset the Check Engine light on my Kia?
Write down all the codes that are Present or Current. Fix all problems that trigger these fault codes. Go back to the menu and select Fault Fault Codes. This will reset the check engine light on you, Kia. Can’t reset the check engine light? First, you need to fix all the underlying problems that triggered the fault codes.
What causes the Check Engine light to go off?
If the gas cap is loose, tighten it and continue driving. Even after tightening, it will take some time for the light to go off. The check engine light is most commonly caused by one of five factors; the O2 sensor, a loose gas cap, the catalytic converter, the mass airflow sensor or the vehicle’s spark plug wires.
Why is my Kia check engine light not working?
Your oxygen sensor measures the amount of unburned oxygen in your vehicle’s exhaust system. If you don’t have it replaced your engine will burn more fuel then needed, you will have a loss in fuel economy, and faulty sensors can cause damage to your spark plugs and catalytic converter.
The maintenance required light is simply indicating that the car is due for an oil change or other routine servicing. Your Check Engine light will either be orange, yellow, or red, depending on the manufacturer, and it will either be the words ‘CHECK ENGINE’ or it will be shaped as an engine.
Where can I Reset my Kia engine light?
If you don’t, you can easily drop in to Horne Kia’s service department and have us reset your engine light for you while you wait. Our Horne Kia dealership is just a short drive from Phoenix, Chandler, Tempe, and anywhere in the Greater Pheonix Area. Ok.
How can I get my Check Engine light to go off?
One of the possible ways of getting your check engine light to go off is pulling off the engine control unit’s fuse and then putting it back again. Although this won’t solve the problem in newer cars, it may solve the problem in a little bit older cars, and it is easy to try. Check your repair manual to find the fuse to the engine control unit.
If the gas cap is loose, tighten it and continue driving. Even after tightening, it will take some time for the light to go off. The check engine light is most commonly caused by one of five factors; the O2 sensor, a loose gas cap, the catalytic converter, the mass airflow sensor or the vehicle’s spark plug wires.
What are the codes for Kia check engine light codes?
P1633Battery Overcharge P1634Alternator “B” Open (1.8L) P1655Unused Power Stage ‘B’ P1660Power Stage Group ‘B’ P1665Power Stage Group ‘A’ P1693MIL Circuit Malfunction P1743Torque Converter Clutch Solenoid Valve Open Or Short
How can I read the Check Engine Light code?
You can read Kia check engine light codes yourself using an OBD-II scanner. This method applies only to Kia vehicles that are the model year 1996 and newer. Locate the OBD-II port under the dashboard. Plugin your scanner into the OBD-II port. Turn on the ignition. Do not start the engine.
One of the possible ways of getting your check engine light to go off is pulling off the engine control unit’s fuse and then putting it back again. Although this won’t solve the problem in newer cars, it may solve the problem in a little bit older cars, and it is easy to try. Check your repair manual to find the fuse to the engine control unit.
Kia Check Engine Light (CEL) (also known as Service Engine Soon SES or MIL) may sometimes turn on and stay on when driving. This problem can effect Kia models such as: Sedona and other models.
You can read Kia check engine light codes yourself using an OBD-II scanner. This method applies only to Kia vehicles that are the model year 1996 and newer. Locate the OBD-II port under the dashboard. Plugin your scanner into the OBD-II port. Turn on the ignition. Do not start the engine.
Write down all the codes that are Present or Current. Fix all problems that trigger these fault codes. Go back to the menu and select Fault Fault Codes. This will reset the check engine light on you, Kia. Can’t reset the check engine light? First, you need to fix all the underlying problems that triggered the fault codes.
What does it mean when your check engine light is blinking?
If the check engine light is flashing, it means there is a critical problem that needs to be addressed right away. If this ever happens when you are driving, pull over as soon as it is safe to do so. Allow the engine to cool down. When the check engine light is blinking, it is not safe to operate the vehicle.
What does a flashing check engine light mean?
A flashing check engine light means stop driving as soon as you can get the car to a safe stop. It is usually a misfire, dumping unburned fuel in the exhaust, which will roach your catalytic converter. Big $$$ repair if that happens.
Why is my Check Engine light on in my Bugatti Chiron?
The monstrous Bugatti Chiron has 16. No matter how many you have though, a malfunctioning coil will almost certainly trigger the check engine light, but remember, if your car burns diesel, you have neither ignition coils nor spark plugs.
Where to find check engine light code on Kia?
When retrieving Kia check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
How many miles does a Kia Sedona have?
I have a 2005 Kia Sedona with about 56k miles on the clock. I’ve had it since new and its been pretty good on the whole. However, it has developed the stalling issue you have posted this last week. Its happened maybe 10 times in the past 3 days and happens after about 20 minutes running.
Why are the spark plugs on my Kia not working?
Spark plugs ignite the fuel/air mixture in the combustion chamber of your vehicle. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If you don’t replace it you will experience poor performance and reduced fuel economy and worn plugs can cause a clogged catalytic converter or damage to ignition coils and O2 sensors.
What does a check engine light mean on a Kia?
A solid check engine light is usually no cause for panic. The indicator is triggered when your Kia’s on-board computer (ECU – Electronic Control Unit) finds something out of the normal with its usual function. When it discovers a problem, it records it using a diagnostic code.
Spark plugs ignite the fuel/air mixture in the combustion chamber of your vehicle. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If you don’t replace it you will experience poor performance and reduced fuel economy and worn plugs can cause a clogged catalytic converter or damage to ignition coils and O2 sensors.
Is the Kia Sorento a safe car to drive?
Lucky for all Kia drivers, the on-board diagnostics and repair systems are getting better and better every year. The 2019 Kia Sorento, for instance, features a number of important features that make driving safer than ever. How Bad is the Check Engine Light on Kia Cars?
When does the Kia check engine light turn off?
Kia Check Engine Light (CEL) (also known as Service Engine Soon SES or MIL) should not stay on when you are driving. The Check Engine Light should stay on when you turn the ignition to ON position, and until you start the engine, the light should turn off.
Why does my check engine light keep turning on?
The ECU stores a diagnostic trouble code (DTC) in its memory, triggering your check engine light to turn on the dashboard. Any number of things can cause this problem – it may be as simple as a loose gas cap, a problem with an incorrect fuel/air mixture, or something much more severe as an engine problem.
Kia Check Engine Light (CEL) (also known as Service Engine Soon SES or MIL) should not stay on when you are driving. The Check Engine Light should stay on when you turn the ignition to ON position, and until you start the engine, the light should turn off.
The ECU stores a diagnostic trouble code (DTC) in its memory, triggering your check engine light to turn on the dashboard. Any number of things can cause this problem – it may be as simple as a loose gas cap, a problem with an incorrect fuel/air mixture, or something much more severe as an engine problem.
When does the Check Engine light come on?
The Check Engine Light should stay on when you turn the ignition to ON position and until you start the engine, after that the light should turn off. If the light continues to stay on, that means there is a problem and you need to get your car diagnosed.
How can I Reset my Check Engine light?
The simplest way to reset the check engine light yourself is to use the OBD-II scanner. You can use an inexpensive scanner such as the Autel MaxiScan OBD2 Scan Tool which is a handheld unit or an ELM327 Bluetooth Adapter and your phone. The scan tool plugs into the OBD-II port located underneath the steering wheel.
Where is the Check Engine light on a Kia?
This method applies only to Kia vehicles that are the model year 1996 and newer. Locate the OBD-II port under the dashboard. Plugin your scanner into the OBD-II port. Turn on the ignition. Do not start the engine. Allow the scanner to power on. Select Read Codes on your scanner. Write down all the codes that are Present or Current.
What are the warning lights on a Kia?
Some of the most important dashboard warning lights found on a Kia vehicle include: Should any of the warning lights highlighted above ever show up on your dashboard, you should take some immediate action to have your Kia vehicle inspected as soon as possible!
What to do when check engine light comes on?
Locate the OBD-II port under the dashboard. Plugin your scanner into the OBD-II port. Turn on the ignition. Do not start the engine. Allow the scanner to power on. Select Read Codes on your scanner. Write down all the codes that are Present or Current. Fix all problems that trigger these fault codes.
What are the names of the Kia warning lights?
They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 70 of them, so search carefully! Models examined include Cadenza, Carnival, Forte, K5, K900, Niro, Optima, Rio, Sedona, Seltos, Sorento, Soul, Sportage, Stinger and Telluride.
What are the components of a Kia Sedona?
1. Engine Control Module (ECM) 2. Barometric Pressure Sensor (BPS) 3. Manifold Absolute Pressure Sensor (MAPS) 4. Intake Air Temperature Sensor (IATS) 5. Engine Coolant Temperature Sensor (ECTS) 6. Throttle Position Sensor (TPS) [integrated into ETC Module] 7. Crankshaft Position Sensor (CKPS) 8. Camshaft Position Sensor (CMPS) [Bank 1 / Intake]
When do Kia Sorento engines hesitate during acceleration?
Kia Sorento Engine hesitates during acceleration Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now.
Kia Sorento Engine hesitates during acceleration Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now.
Can you install paddle shifters on a Kia Sorento?
2020 Forte GT Line Battery Light Comes On Intermed… 07 stereo wiring? 08 Optima 2.4 Timing Chain question. Please help Has anyone been able to install paddle shifters on 2016 Sorento?
What should I do about my 2016 Kia Sorento?
Aftermarket Grille replacement? 2020 Forte GT Line Battery Light Comes On Intermed… 07 stereo wiring? 08 Optima 2.4 Timing Chain question. Please help Has anyone been able to install paddle shifters on 2016 Sorento? Remove MAF sensor – Pull out of intake housing? Lack of dealers? Backup Camera harness on the trunk already?
Why does my Toyota Corolla hesitate during acceleration?
When a vehicle is hesitating during acceleration, it should be inspected by a mechanic. A vehicle with a combustion (gas or diesel) engine requires an exact mixture of fuel and air to run efficiently. If this mixture is thrown off in any way, it may result in an engine running too lean (not enough air), or too rich (not enough fuel).
When retrieving Kia check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
What causes your car to shut off while driving?
When the ignition switch is frazzled, this will lead to a loss or power to your engine due to vibration such as hitting a round patch of street. The loss of power causes the engine of your car to die suddenly while you are driving on the road. Check out this video to see more details:
Can a Kia Sorento engine shut off while driving?
Hello , I was driving my 2016 kia Sorento and my car engine just shut off and stopped while driving. This needs to be readdress and made sure all kia Sorento do not have the same problem. It was very scary while driving on a highway and this happening. Was driving on the freeway and heard a sound as if I had ran over a piece of plastic.
Is there no oil light on Kia Sorento?
We discovered there was little to no oil on the dipstick, there was no oil light warning, no engine light or any other signs it was low on oil. The oil has been changed regularly.
P1633Battery Overcharge P1634Alternator “B” Open (1.8L) P1655Unused Power Stage ‘B’ P1660Power Stage Group ‘B’ P1665Power Stage Group ‘A’ P1693MIL Circuit Malfunction P1743Torque Converter Clutch Solenoid Valve Open Or Short
What to do when your Kia Sedona goes down a hill?
When you park on a hill apply the parking brake before you put the vehicle in park. this way the weight of the vehicle is on the brake rather than the transmission. this will solve the issue I simply have a tough time moving the gear shift from park down to drive smoothly.
Why does my Kia Sedona not shift gears?
This is a common issue on all transmissions. When you park on a hill apply the parking brake before you put the vehicle in park. this way the weight of the vehicle is on the brake rather than the transmission. this will solve the issue I simply have a tough time moving the gear shift from park down to drive smoothly.
Why does my Kia Sedona engine not start?
There are a lot of issues that can cause your Sedona to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code. It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes.
Where is the diagnostic connector on a Kia engine?
Scan Tool for Codes and Live Data for your Kia Engine from $149.95 Kia Engines – Please select the connector for your vehicle from the options below. This connector is usually located under the driver side dash panel. Locations: Left-hand side of firewall. Near or in the fuse box, or near the battery.
What to do when your Sedona won’t start?
When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Sedona, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it.
How do you retreve a Kia Chech engine?
Kia has two methods of retreving codes with some overlap between different models and years. Method One attempts to generate the codes on the Chech Engine Light. We recommend trying this method first. Method Two attempts to generate the codes using a Voltmeter or LED Tester.
Locate the OBD-II port under the dashboard. Plugin your scanner into the OBD-II port. Turn on the ignition. Do not start the engine. Allow the scanner to power on. Select Read Codes on your scanner. Write down all the codes that are Present or Current. Fix all problems that trigger these fault codes.
Can a check engine light go off by itself?
Will the check engine light go off by itself? Yes, The check engine light will reset itself after a fixed amount of time if you fixed the problem in most car models. Usually, this is 10-30 cycles. One cycle is from a cold start until the engine is at working temperature.
Is it OK to clean the gas cap?
It should be fine. With all of that said, plan on replacing the gas cap whether this cures your ill or not. It sounds like the seal is worn out and just barely doing the job. Cleaning the seal is usually only a temporary fix. Realistically, @Zaid is spot on.
What to use to clean gas tank intake?
Clean the metal part (the top of the gas tank intake) with a “petroleum-based lube”. Cover the rubber seal on the gas cap with a “silicon-based spray” to prevent the petroleum-based lube from deteriorating the rubber.
What does check engine light on Kia Sportage mean?
A check engine light can indicate a broad spectrum of problems with your 2008 Kia Sportage. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.
How to replace the gas cap on a check engine light?
Install/Replace The Gas Cap Properly 1 Fully install the cap into the filler tube. 2 Make sure the threads sit and seal properly. 3 Turn the gas cap clockwise to tighten it. 4 Continue to do so until you hear the cap clicking three times. More
When did I Buy my 2002 Kia Sedona?
We bought our Sedona new in 2002. It was a daily driver while the kids were in car seats, now it’s our road-trip and weekend car. We bought one of the first ones that came off the boat, and it had all the problems the reviewers said it would have.
What kind of engine does a Kia Sedona have?
The Sedona carries a 3.5-liter dual-overhead-cam V-6 engine that develops 195 horsepower. Kia claims it has the largest-displacement engine available in an import-brand minivan. The V-6 runs on regular gasoline and drives a five-speed-automatic transmission.
How many seats does a Kia Sedona have?
Dual sliding side doors are standard. The step-up EX model adds a body-colored roof rack and defogger-equipped mirrors, fog lights and alloy wheels, as well as additional chrome body trim. The Sedona seats seven occupants with bucket seats in the first and second rows and a split bench in the third row.
What are the special tools for Kia Sedona?
Special Service Tools Tool Name / NumberIllustrationDescriptionCrankshaft front oil seal installer09231-3C100Ring gear stopper09231-2B100Used for keeping ring gear from rotating when removing / i
Do you have to replace cylinder cap on Kia Sedona?
For information on SAE viscosity grades based on ambient temperatures, refer to the “Lubrication System”. Torque-to-yield cylinder head, connecting rod cap and crankshaft main bearing cap bolts must be replaced once removed because the bolts are designed to be permanently elongated beyond the state of elasticity when torqued.
What causes a check engine light on a Kia Rio?
The check engine light is most commonly caused by one of five factors; the O 2 sensor, a loose gas cap, a faulty catalytic converter, the mass airflow sensor or the vehicle’s spark plug wires. What does the check engine light mean on a Kia Soul or Kia Rio? Ok, now it’s time to answer the all-important question.
What does the Check Engine light on Kia Soul mean?
A lit up warning light in your Kia Soul, for example, could indicate something as simple as a loose gas cap. Then again it could also mean the failure of something more important. The check engine light essentially means that your vehicle’s onboard computer system has self-diagnosed a problem.
What was the problem with my Kia Sorento?
It was inconsistent stalling (4 times in 3 years) that couldn’t be duplicated when taken to the dealership. If I put the Sorento in park and restart it would be fine. It would only happen when I stop and go. Final time it stalled out for good on the freeway.
How many times does a Kia Sorento stall?
More than one Kia Sorento owner went so far as to post a video on YouTube. Frankly this video is not worth watching but what she said is worth noting, her Sorento stalled six times with no results from the dealership who was as stumped as she was.
What do the dashboard warning lights on your Kia vehicle Mean?
Some of the most important dashboard warning lights found on a Kia vehicle include: Anti-Lock Brake System (ABS) Warning Light Indicates a malfunction in the Anti-Lock Brake System Electronic Brake Force Distribution (EBD) System Warning Light
Why is the EPs warning light not working on my Kia?
You should contact your Kia dealership immediately. Also, the speedometer or odometer/tripmeter may not work, the EPS warning light may illuminate and the steering effort may increase or decrease. Symbol will illuminate when the engine enters the Idle Stop mode of the ISG (Idle Stop and Go) system.
1. Engine Control Module (ECM) 2. Barometric Pressure Sensor (BPS) 3. Manifold Absolute Pressure Sensor (MAPS) 4. Intake Air Temperature Sensor (IATS) 5. Engine Coolant Temperature Sensor (ECTS) 6. Throttle Position Sensor (TPS) [integrated into ETC Module] 7. Crankshaft Position Sensor (CKPS) 8. Camshaft Position Sensor (CMPS) [Bank 1 / Intake]
Why does the Gas Light Come on in my Kia?
Maybe you were jamming out to your favorite song and paying more attention to your UVO infotainment system than you were to your fuel gauge, but suddenly you find the fuel light has illuminated your dash.
What does the Kia dashboard warning light mean?
Kia dashboard warning lights are a combination of universal recognised symbols and symbols unique to Kia. The colour of the light will typically signify the importance or severity of the issue.
What to do if Kia front light comes on while driving?
If it comes on whilst driving or remains on after engine ignition, we recommend that the system be seen by an authorised Kia dealer. Vehicle can still be used, though steering may become more difficult. If the AFLS malfunction symbol illuminates, the Adaptive Front Lighting System is not working properly.
Some of the most important dashboard warning lights found on a Kia vehicle include: Should any of the warning lights highlighted above ever show up on your dashboard, you should take some immediate action to have your Kia vehicle inspected as soon as possible!
What does it mean when your check engine light comes on?
The check engine light essentially means that your vehicle’s onboard computer system has self-diagnosed some kind of problem. This problem can be anything from a momentary hiccup, something like a loose gas cap or a change in humidity, to the failure of a major component like a bad catalytic converter.
They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 70 of them, so search carefully! Models examined include Cadenza, Carnival, Forte, K5, K900, Niro, Optima, Rio, Sedona, Seltos, Sorento, Soul, Sportage, Stinger and Telluride.
What to do if your check engine light is flashing?
Since cars are complicated machines with over 2,000 parts needing to function in synchronicity, you should never continue to drive a vehicle with a flashing check engine light. When it is safe, pull over and call a tow truck, have your vehicle taken to the nearest Kia-certified service center.
When does a car go into limp mode?
The Step-By-Step Process When a computer system in the car generates an emergency signal implying a transmission issue, it is through the “limp mode.” It is a foolproof mechanism that protects the car and the car inhabitants from further damage. Once your car gets into the limp mode, you would have to move out of it too.
When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Sedona, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it.
Lucky for all Kia drivers, the on-board diagnostics and repair systems are getting better and better every year. The 2019 Kia Sorento, for instance, features a number of important features that make driving safer than ever. How Bad is the Check Engine Light on Kia Cars?
When did the Kia Sedona fuse box come out?
In this article, we consider the first-generation KIA Sedona, produced from 2002 to 2005. Here you will find fuse box diagrams of KIA Sedona 2002, 2003, 2004 and 2005, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout).
I have a 2005 Kia Sedona with about 56k miles on the clock. I’ve had it since new and its been pretty good on the whole. However, it has developed the stalling issue you have posted this last week. Its happened maybe 10 times in the past 3 days and happens after about 20 minutes running.
How often do you change the oil on a Kia Sorento?
Add fuel additive *1 (30,000 miles (48,000 km) or 48 months) Inspect manual transaxle fluid (Every 40,000 miles or 48 months) Replace engine oil and filter (37,500 miles (60,000 km) or 60 months) Add fuel additive *1 (37,500 miles (60,000 km) or 60 months) Inspect battery condition
When does the Kia maintenance light go off?
The computer system tracks the engine miles from the time it was reset, and the light will trigger after a certain amount of miles driven (i.e. 5,000 miles, or 7,500 miles). When the system counts down to zero, your vehicle should have already been serviced, or it should be serviced as soon as possible.
How does service required work on a Kia?
A message, “SERVICE REQUIRED,” will appear each time the ignition is switch turned to the “ON” position. The computer system tracks the engine miles from the time it was reset, and the light will trigger after a certain amount of miles driven (i.e. 5,000 miles, or 7,500 miles).
The computer system tracks the engine miles from the time it was reset, and the light will trigger after a certain amount of miles driven (i.e. 5,000 miles, or 7,500 miles). When the system counts down to zero, your vehicle should have already been serviced, or it should be serviced as soon as possible.
A message, “SERVICE REQUIRED,” will appear each time the ignition is switch turned to the “ON” position. The computer system tracks the engine miles from the time it was reset, and the light will trigger after a certain amount of miles driven (i.e. 5,000 miles, or 7,500 miles).
Why do I get a reminder on my Kia?
The sole function of Kia’s Maintenance Reminder system is to remind owners when to take their car in for a scheduled service. A message, “SERVICE REQUIRED,” will appear each time the ignition is switch turned to the “ON” position.
Why does my check engine light keep coming on?
Occasionally, the Check Engine light comes on when nothing is wrong with the car. It could be a temporary problem caused by a tank of bad gas or a range of other factors. In such cases, the light should go off by itself after a short time.
Occasionally, the Check Engine light comes on when nothing is wrong with the car. It could be a temporary problem caused by a tank of bad gas or a range of other factors. In such cases, the light should go off by itself after a short time.
If the check engine light is flashing, it means there is a critical problem that needs to be addressed right away. If this ever happens when you are driving, pull over as soon as it is safe to do so. Allow the engine to cool down. When the check engine light is blinking, it is not safe to operate the vehicle.
What’s the problem with the Kia Sedona transmission?
I had the same problem with our (now traded) 02 sedona. The vehicle speed output sensor is bad. Go to KIA spend $200 bucks for it, grab a long extension with a swivel on the end and a 10 mm ( I think…it’s been almost a year ( the sensor sits on the top of the transmission and is kinda hard to get to.
Is the Kia Sedona LX a good car?
I just purchased a 2007 Sedona LX, and noticed something different about how it drives versus the last car I owned. In the Sedona, I’ve noticed as I take my foot off the gas and try to coast, I can feel the engine slowing the vehicle more rapidly than I thought was normal.
Is the alternator on my Kia Sedona bad?
I have a 2002 kia sedona with 59,250 miles and have had the van since Jan 2006. I had to have the alternator replaced about 6 weeks ago and today found out that I have a valve that is bad and needs to be repaired.
What should I do if my Kia Sorento warning light is not working?
Then check all brake components for fluid leaks. If any leaks in the brake system is still found, the warning light remains on, or the brakes do not operate properly, do not drive the vehicle. In this case, have your vehicle towed to an authorized Kia dealer and inspected.
What does p0304 mean on Kia cylinder 4?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. P0304 KIA Tech Notes The P0304 code means that the cylinder 4 is misfiring or is randomly misfiring. Start by checking for intake leaks and if no leaks are found the next step is to replace the spark plugs on cylinder 4.
What to do if your p0306 cylinder 6 is reset?
Now, clear the codes and see if the P0306 is reset during a lengthy test drive. If the code is reset, use your vehicle information source to search technical service bulletins (TSB) which pertain to the symptoms and code (s) in question.
Why do I have OBD code p0306 on my car?
Although generic, the specific repair steps may vary depending on make/model. The reason for a code P0306 being stored in your OBD II vehicle is that the powertrain control module (PCM) has detected an individual cylinder misfire.
How many miles do you need to service a Kia?
30,000 Miles – All 15,000-mile services, plus brake fluid, transmission fluid, and coolant replacement 60,000 Miles – Identical to 30,000-mile service, plus replacement of timing belt and spark plugs, as necessary
Is it important to keep up with Kia maintenance?
After you buy a new Kia or used vehicle near Harvey, it’s important to keep up with regular car services to ensure that it runs properly for years to come. Not only does this help you get the most out of your investment, but routine maintenance saves you from having to pay for more serious, and more expensive, issues down the road.
How much does a 2006 Kia Sedona cost?
Bought it new and fought to keep it on the road. At 115K miles it has a siezed engine. $6000-$7000 is my estimate. Not a chance. Moving on from this loser a
Is there a problem with the Kia Sedona?
CARS.COM Vehicles Affected: Approximately 220,000 model-ear 2006-14 Kia Sedona minivans manufactured from June 15, 2005, through April 4, 2014 The Problem: The secondary hood latch… Read more Kia Motors Corp. makes the best minivan for the money — better than the Toyota Sienna, Honda Odyssey, Chrysler Town & Country or the Dodge Caravan.
Is the Kia Sedona minivan a good car?
The reworked-for-2006 Kia Sedona has pulled off one of the greatest doubles in auto safety engineering history. Not only did it win the top-… Read more The Kia Sedona minivan is a huge steaming pile of who cares, and I for one couldn’t be more relieved.
The second generation Sedona was the second top selling large MPV in the UK market, and in 2010 received a new grille, new equipment (including a reversing camera built into the rear-view mirror) and a single engine choice, a 192 PS 2.2 CRDi I4 replacing the 183 PS 2.9 CDRi.
Is the Kia Sedona Still on the market?
Kia had announced that the 2012 Kia Sedona will be the last Sedona for the American market. In May 2012, Kia told The Car Connection that the Sedona would be discontinued in the U.S. market after the 2012 model year, but a company spokesperson said the company did not expect to permanently exit the minivan market.