What is the code for Crank no start?
Come along with Eric O. at the SMA shop as he has a look at this 2009 Chevrolet 1500 5.3 that was towed in as a crank no start. It has a code stored in it U0109 for “loss of communication with fuel pump control module.” You can follow along with Eric O. as he brings you along and diagnosis the FPCM.
Can a normal code reader read 10 codes?
Normal code reader cannot comunicate with or read codes. But power to OBDII plug. Snap-On scanner can read codes but only recognizes 10 systems and 8 codes with cleared and return. Snap-On Scanner will not Auto ID car and says Comm problem.
Will you allow code readers to read your ECM?
No Communication: Will Not Allow Code Readers to Read My Ecm. I Will not allow code readers to read my ecm. I keep getting “link error”. Any ideas on how to troubleshoot and what to be expecting
How many codes can a snap on scanner read?
Snap-On scanner can read codes but only recognizes 10 systems and 8 codes with cleared and return. Snap-On Scanner will not Auto ID car and says Comm problem.
What to do if your car says no crank no click?
GM has issued a technical service bulletin (TSB) #PIP4208 to deal with a no crank, no start, no click situation on the following vehicles: The starting procedure on these vehicles is fairly complicated and the root problem lies in the ignition switch.
What causes your check engine light to not come on?
If your check engine light hasn’t come on, you may want to check the following: This other post examines in more detail the causes of an engine that won’t crank over. It has some simple tests to help you fix the problem. A loose or damaged fuel filler cap can cause your engine to stall. Photo in the Public Domain. III. My Engine Stalls
How can I start a check light on my car?
The picture to the right show a typical example of bridging 2 terminals of a diagnostic connector to start a Check Light flashing on the dashbaord. The website pages will now generally ask you to turn the Ignition Key On. A Check Light on the Dash will now begin to Flash as shown in the diagram to the right.
What does no start no crank no click mean?
If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that. In the old days, power flowed through the ignition switch and down to the starter solenoid. Not anymore.
What to do when your car cranks but won’t start?
If the coil is sparking and the rotor turning, check ignition timing. If there’s no spark, check the points or ignition module. If the rotor isn’t turning, the distributor shaft has most likely snapped and you need to replace the distributor. Check the condition of the distributor cap. Is the underside of the cap wet?
What to do when your odometer says no start?
Disconnect the battery, Unplug all the connectors from the module, and try to clean both the plugs on the wires and the module, once it’s all dry, reconnect and then reconnect the battery. if that still doesn’t do it then you need a new PCM.
How can I tell if my distributor has a spark?
Without a spark tester, you can disconnect a plug wire at the distributor and hold it a fraction of an inch from its terminal on the distributor and see if a spark will arc to the plug wire. Replace the coil wire and remove the distributor cap and verify the rotor turns when the engine rotates.
Come along with Eric O. at the SMA shop as he has a look at this 2009 Chevrolet 1500 5.3 that was towed in as a crank no start. It has a code stored in it U0109 for “loss of communication with fuel pump control module.” You can follow along with Eric O. as he brings you along and diagnosis the FPCM.
Is there a truck that won’t start?
Have a 11 international dt that won’t start. Bought the truck last a little over a year ago and had to rebuild engine after one month $$$. Few months later had to replace hpop.
Why does my car not start when I crank the engine?
If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.
What does it mean when your car says no crank?
A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. The most common problem, that causes this condition is a failed starter motor.
Why does my GM 4.3L engine not start?
No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.
What does it mean when your car says no start?
A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).
Why does my Chevy C5500 have no crank?
It has no crank not start once you hit the key. Replaced the starter same issue, fuses look good. We did get it to start but by bumping the terminals on the starter with a screw driver. Any thought on what could be going on?
What to do if your truck won’t click and crank?
I bought a new starter, put it on, then hunted wires for 2 days before realizing that fuse was blown. So if your truck won’t click and crank, don’t forget about that little 30 amp fuse when you start your problem hunt. Thanks for helping me out, guys!
What happens when there is no power to the starter motor?
If there’s no power to the starter motor but power everywhere else you’d hear a “click!” noise when you turned to start but nothing else – ie. no whirring or cranking noises.