What does the Mercedes Fault code p0801 mean?
Mercedes Fault Code Fault Code Meaning; P0801: Reverse Inhibit Control Circuit Malfunction: P0803: 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction: P0804: 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction: P0805: Clutch Position Sensor Circuit Malfunction: P0806: Clutch Position Sensor Circuit Range/Performance: P0807
Can you read the fault code on a Mercedes Benz?
Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS
What does Mercedes Fault code p0400 mean?
P0400 Mercedes Fault Codes Meaning Mercedes Fault Code Fault Code Meaning P0466 Purge Flow Sensor Circuit Range/Performa P0467 Purge Flow Sensor Circuit Low Input P0468 Purge Flow Sensor Circuit High Input P0469 Purge Flow Sensor Circuit Intermittent
What are the Mercedes OBD-II Diagnostic Trouble Codes?
This is the list of Mercedes specific OBD-II Diagnostic Trouble Codes (DTC’s) that are used by Mercedes to diagnose the vehicle problems. This codes are presented for information only. You can always refer to the list of Standard or generic OBD-II DTC. P1105 Atmospheric pressure sensor Readout too large.
Is the p1617 EEPROM code incorrectly coded?
P1617 EEPROM or incorrectly coded MT has been coded as AT. P1630 Drive authorization Key used is inhibited. P1663 Y74 (Pressure control valve) The signal voltage is too high.
What is the fault code for Mercedes Benz?
P1520 S40/4 (CC switch with variable speed limiter) DTR operating unit has contact short (two contacts simultaneously). P1520 S40/4 (CC switch with variable speed limiter) No check contact. P1520 S40/4 (CC switch with variable speed limiter) Operating parts signals through CAN are implausible.
Which is faulty P2002 or P2004 control module?
P2002 Component N15/3 (ETC control module) is faulty. P2003 Component N15/3 (ETC control module) is faulty. P2004 check external voltage supply.Control of holding relay K40/7km (relay CDI) cutoff too early. P2004 check external voltage supply.Relay (diesel engine voltage supply relay) cutoff too late.
What’s the fault code for a 2001 Mercedes Benz?
Click to expand… For the ML class it does not apply to the 2001 models. Also the fault code in the bulletin is for DTC B9103 and DTC B9123. No others would be covered by the DTB. Post # 34 in this thread lists the DTB the parts, and all affected models.
What does Mercedes Fault code p261f71 mean?
Common Mercedes Error Messages – Explained: Mercedes Fault Code: P261F71. Fault Code Meaning: The output for circulation pump has a malfunction. Actuator is blocked. Known Problem Of: Mercedes Sprinter Vans. Likely Causes: Coolant intrusion into vacuum system via the water pump.
What does the p0101 Mercedes Benz code mean?
Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor. What does this mean? The cost of diagnosing the P0101 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city.
Is there a factory default setting for p0101?
For pollution purposes, the CEL may be triggered long before the car becomes undriveable – as a matter of fact, what now triggers a CEL, would have been considered as very good settings back in the days of carburettors. Kobus, is there a factory default setting the ECU uses if the MAF should become defective?
How much does it cost to repair a p0101 Chevy?
The cost of diagnosing the P0101 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
When to set the p0101 mass air flow code?
The P0101 code is set when the Powertrain Control Module (PCM) detects that the Mass Air Flow (MAF) sensor frequency is below a predetermined value. The Mass Air Flow (MAF) sensor measures the amount of air ingested by the engine.
What is fault code b1859 on Mercedes Benz?
There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.
What is the incorrect codeword for Mercedes Benz?
P1617 EEPROM or incorrectly coded Codeword is incorrect or missing. P1617 EEPROM or incorrectly coded MT has been coded as AT. P1630 Drive authorization Key used is inhibited.
What is MIL-a-21180d, high strength aluminum alloy castings?
MIL-A-21180D, MILITARY SPECIFICATION: ALUMINUM-ALLOY CASTINGS, HIGH STRENGTH (05 NOV 1984) [S/S BY SAE-AMS-A-21180]., This specification covers the requirements for six alloy compositions, four inspection classes, four radiographic quality grades and six classes of mechanical properties of high strength aluminum-alloy castings.
Mercedes Fault Code Fault Code Meaning; P0801: Reverse Inhibit Control Circuit Malfunction: P0803: 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction: P0804: 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction: P0805: Clutch Position Sensor Circuit Malfunction: P0806: Clutch Position Sensor Circuit Range/Performance: P0807
When was mil-8625f anodic coatings approved for use?
MILITARY SPECIFICATION ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS This amendment forms a part of MIL-A-8625F, dated 10 September 1993, and is approved for use by all Departments and Agencies of the Department of Defense.
There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.