What does p0717 input turbine speed sensor circuit no signal trouble code?

If you have a P0717 Input Turbine Speed Sensor Circuit No Signal trouble code, this post will help you understand what it is and how to fix it. The computer wants to know if the transmission is working properly. So it reads the speed of the input shaft and compares it to the speed of the output shaft.

What are the common causes of p0717 code?

Here are the common causes of the P0717 code: 1 Malfunctioning input speed sensor 2 An issue with the speed sensor circuit 3 An issue with the powertrain control module or transmission control module

What does DTC p0717 mean on Honda Accord?

Diagnostic Trouble Code (DTC) P0717 is detected when TCM or ECM receives no signal from the sensor. P0717 Honda Possible Symptoms. P0717 Honda Meaning. The Input Speed Sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

When is the input shaft speed sensor no signal?

Diagnostic Trouble Code (DTC) P0717 is detected when TCM or ECM receives no signal from the sensor. The Input Speed Sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module ( ECM ).

What does the OBDII code p0717 mean?

P0717 Meaning. The Input Speed Sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). The ECM sets the OBDII code when the Input Speed Sensor is out of factory specifications.

What is the input shaft speed of a DTC p0717?

P0717 The transmission input shaft speed is less than 50 RPM for 5 seconds. DTC P0716 and P0717 are Type B DTCs. The TCM commands maximum line pressure. The TCM freezes transmission adapts. The TCM calculates input speed from the automatic transmission output shaft speed sensor and commanded gear.

Where is the p0717 code stored in the PCM?

Code P0717 will be stored if the PCM detects the input sensor signal is missing for a given period of time. RPMs are transferred from the engine to the transmission while a reluctor wheel (often mounted on the input shaft) spins and passes close to the tip of the sensor.

When is the p0717 diagnostic trouble code detected?

When is the P0717 code detected? Diagnostic Trouble Code (DTC) P0717 is detected when TCM or ECM receives no signal from the sensor. The Input Speed Sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module ( ECM ).

What causes no TSS signal on DTC p0717?

Depending on year, make, and model, DTC P0717 may have number of causes. Here are some of the most common. 2000-2002 General Motors – Some vehicles in the GM lineup suffered a problem of poor electrical connection between the TCM and TSS, particularly in the 20-pin connector at the transmission.

Can a p0717 code cause a car to stall?

With so many symptoms affecting the drivability and performance of the vehicle, the P0717 code is absolutely a serious problem. It may not completely stop the vehicle from operating, but it can cause a number of dangerous situations, including stalling in traffic and/or unpredictable shifting.

What does the p0717 code on a speedometer mean?

The P0717 indicates a complete loss of circuit voltage for the input/turbine speed sensor. Symptoms of a P0717 code may include: Intermittent or erratic speedometer (odometer) operation

Why is there no signal on my p0717 sensor?

Failure to disconnect related controllers, prior to testing resistance or continuity (using the DVOM), may result in controller failure. If a code P0717 is stored, and all system circuits and sensors are in proper working order and comply with manufacturer’s specifications, suspect a faulty PCM or a PCM programming error.

How to fix a p0717 OBD-II trouble code?

Some of the most likely repairs to fix a P0717 code are: Replacing the valve body. Replacing the input/turbine speed sensor. Replacing one or more shift solenoids.

When to set the p0717 powertrain control module code?

The PCM (powertrain control module) will set the P0717 code when it detects no signal from the input/turbine speed sensor. This signal may be interrupted briefly, or it may be erratic or otherwise outside of expected manufacturer settings.

What happens when turbine speed sensor does not work?

If the output shaft speed doesn’t match the expected speed, the computer knows something is slipping inside the transmission. It can then try to boost the fluid pressure to compensate. If that doesn’t work, it sets a different trouble code. But first it needs the input from the input turbine speed sensor.

What is a p code for turbine speed?

Trouble Codes > P Code Definitions > Generic non-manufacturer-spec… > P0717 Input Turbine Speed… If you have a P0717 Input Turbine Speed Sensor Circuit No Signal trouble code, this post will help you understand what it is and how to fix it. The computer wants to know if the transmission is working properly.

What is the diagnostic code for input speed sensor?

P0715 is a diagnostic trouble code (DTC) for “Input/Turbine Speed Sensor Circuit Malfunction”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.

What is the OBD code for a turbine speed sensor?

The A designation is typically reserved for OBD-II equipped vehicles that use multiple input or turbine speed sensors. The input/turbine speed sensor is usually an electromagnetic, 3-wire sensor used to monitor transmission input speed (recognized by the PCM as revolutions per minute or RPMs).

When to use the diagnostic trouble code p0717?

– Transmission speed sensor circuit is open or shorted. – Poor transmission speed sensor circuit connection – Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0717 Mercedes is detected when TCM or ECM receives no signal from the sensor.

When is the input speed sensor out of factory?

Control Module (TCM) and the Engine Control Module ( ECM ). The ECM sets the OBDII code when the Input Speed Sensor is out of factory specifications. The Diagnostic Trouble Code (DTC) P0717 is detected when TCM or ECM receives no signal from the sensor.

When to set the p0717 check engine light?

What does input / turbine speed sensor no signal mean?

Input/Turbine Speed Sensor A Circuit No Signal This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to all 1996-newer vehicles (Ford, Honda, Mazda, Mercedes, VW, etc.). Although generic, the specific repair steps may vary depending on make/model. What does that mean?

When to use diagnostic trouble code p0717 Nissan?

– Poor transmission speed sensor circuit connection – Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0717 Nissan is detected when TCM or ECM receives no signal from the sensor.

Where is the turbine sensor on a Nissan Leaf?

P0717 Nissan Description. The turbine revolution sensor detects forward clutch drum rpm (revolutions per minute). It is located on the input side of the automatic transaxle. The revolution sensor is located on the output side of the automatic transaxle. With the two sensors, input and output rpms are accurately detected.

What kind of transmission does a Saturn p0716 have?

2007-2009 Saturn Outlook – These vehicles suffered a weak internal transmission component, which would break and result in a number of transmission DTCs, including P0716, P0717, P0776, P0777, P2714, P2715, or P02723.

What does the DTC code p0717 Nissan mean?

– Transmission speed sensor circuit is open or shorted. – Poor transmission speed sensor circuit connection – Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0717 Nissan is detected when TCM or ECM receives no signal from the sensor.

Why is my turbine speed sensor no signal?

If it doesn’t get that signal, the computer sets a P0717 Input Turbine Speed Sensor Circuit No Signal. Either the sensor is dead or there’s a circuit issue (bad wiring, etc). Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period. They include wiring diagrams and technical service bulletins.

Here are the common causes of the P0717 code: 1 Malfunctioning input speed sensor 2 An issue with the speed sensor circuit 3 An issue with the powertrain control module or transmission control module

Is the speed sensor on a Toyota p0793 intermittent?

Was originally intermittent, took it to a shop and they replaced the speed sensor with an aftermarket which made the shifting worse and the problem constant. Took it to a second shop and they replaced the same sensor with a OEM sensor but it didn’t fix the problem.

What is the speed sensor on a Toyota Sienna?

I have a similar transmission and CEL issue on a 2008 Sienna with 120K miles. It started shifting hard (mostly upshift between 1 and 2) and the CEL light came on with P0793 as the code. I replaced the “NC” speed sensor (top of the transmission) with an aftermarket sensor.

What’s the average speed of a p2714 solenoid?

Generally right in the 35 mph to 45 mph range. Example: I am driving around 40 to 45 mph and let of the accelerator going around a curve at at about 25 mph then accelerate after going up hill. If I lightly accelerate and go slow up the hill it did fine.

Where is the speed sensor on a 2wd car?

The vehicle speed sensor is located on the left side of the tailshaft of the transmission for the 2WD model as shown in the diagram below.

How do you test a wire speed sensor?

You’ll still use your multimeter with the clamp leads, and after attaching power and ground, you’ll piggyback the ground (black) lead to the external source ground, and attach the red lead to the output on the sensor. Then it’s time to test the sensor. If playback doesn’t begin shortly, try restarting your device.

What does the code p0715 mean on a transmission?

Code P0715 is triggered when the Engine Control Module (ECM) or Transmission Control Module (TCM) detects an irregular signal coming from the input/turbine speed sensor in the transmission. The input/turbine speed sensor is used to measure how many revolutions per minute (RPM) the input shaft of the transmission is turning.

What should I do about my p0715 speed sensor?

The most common repairs for a P0715 are as follows: Replacing the input speed sensor Repairing damaged wiring for the input speed sensor Additional comments for consideration regarding the P0715 code

https://www.youtube.com/watch?v=6irziDmiU78

Navigation