What does p0714 code on Jeep Commander mean?
The P0714 code tells that there is something wrong with or the temperature sensor, or with the wiring towards it or the PCM. The wiring should be not too difficult to check, but most probably will not be the fault in this case.
Is there anything wrong with my Jeep Commander?
The Jeep is back from the tranny shop, and the mechanic said he can’t justify doing anything at this point, as the codes don’t tell him anything specific that is wrong with the tranny, and the filters, and fluid, which he did change, looked good. Also said there is nothing he can find wrong with the torque converter.
What is the OBD2 code for a jeep?
OBDII Jeep Code Definitions. Be sure to double check the codes. Anything P1000 to P1999 or P3000 to P3400 will be Manufacturer specific and may not match the ones listed here. Check specific manufacturer pages on the site, as some of them, we list the OBD2 codes on those pages for those specific vehicles.
What kind of engine does a Jeep Commander have?
This vehicle has the 4.7 engine with the automatic trans. Currently 130,000 miles on the odometer. I have owned this Jeep since new. This is an intermittent problem that has been going on for a few months. There doesn’t seem to be anything unusual in the way the tranny shifts.
The P0714 code tells that there is something wrong with or the temperature sensor, or with the wiring towards it or the PCM. The wiring should be not too difficult to check, but most probably will not be the fault in this case.
The Jeep is back from the tranny shop, and the mechanic said he can’t justify doing anything at this point, as the codes don’t tell him anything specific that is wrong with the tranny, and the filters, and fluid, which he did change, looked good. Also said there is nothing he can find wrong with the torque converter.
This vehicle has the 4.7 engine with the automatic trans. Currently 130,000 miles on the odometer. I have owned this Jeep since new. This is an intermittent problem that has been going on for a few months. There doesn’t seem to be anything unusual in the way the tranny shifts.
What to do if transmission over temp on Jeep Commander?
He unplugged and cleaned all of the connectors that plug into the tranny, and pinched some of them closer together so as to make a better connection, as he has seen that send faulty readings on trannys in the past, but not on this model.
When to use p0714 transmission fluid temperature sensor?
Code P0714 is set when the PCM detects an intermittent problem with the transmission fluid temperature sensor. An example of a transmission fluid temperature sensor: Related trans fluid temperature sensor “A” circuit codes: P0710 Transmission Fluid Temperature Sensor A Circuit Malfunction
What does transmission over temp on 2006 Commander mean?
An other member found the PCM at fault. On 2005 and on JGC the TCM (transmission control module) is integral to the PCM. The temperature sensor signal goes to the PCM and this one will trigger the overtemp light. What it the PCM? Powertrain Control Module.
What causes p0218 transmission over temperature condition?
If your transmission/transaxle fluid temperature is greater than 290 deg. F then P0218 will set and the overtemp light will illuminate. The number one cause of transmission failure is overheated fluid.
Code P0714 is set when the PCM detects an intermittent problem with the transmission fluid temperature sensor. An example of a transmission fluid temperature sensor: Related trans fluid temperature sensor “A” circuit codes: P0710 Transmission Fluid Temperature Sensor A Circuit Malfunction
What does the p0218 code on a transmission mean?
The P0218 code means that the transmission temperature has exceeded the maximum allowable limit that has been set by the vehicle’s manufacturer. What are the causes of the P0218 code? A leak from any part of the transmission system such as the transmission pan, transmission cooler lines, transmission cooler, or the radiator.
An other member found the PCM at fault. On 2005 and on JGC the TCM (transmission control module) is integral to the PCM. The temperature sensor signal goes to the PCM and this one will trigger the overtemp light. What it the PCM? Powertrain Control Module.