How to line up a torque converter to a flywheel?
When you bolt it to the the flywheel, it will pull out the necessary amount. These guys are all right on the money. Convertor all the way back until the trans is bolted up. There should be a gap between the convertor and the flywheel before you bolt them together. After you bolt it up slide up and grab the lower blower pulley.
What is the torque ratio on a Dia torque converter?
Stall Torque Ratio 2.01:1, Codes: 29530318, 29538348, 29538529, 29541293, 29543003 Numbers are on bar code labels next to mounting pads Year Engine Dia Hub SPL Pilot Mount Pilot Center To Bolt Center Stall 13 3/8″ 2.295 25 1.700 6 Pads 5 3/4″ 35-1BC
How many bolts are in a torque converter?
The new converters will also come with 12 bolts holes in the cover to help if you are running a big HP truck with a billet flexplate. Click to expand… I want to thank ATS for jumping in and helping me out so quickly.
Where can I find a photo of a torque converter?
A photo of the front and rear surfaces of the converter is provided when one is available. Additional data pages are included at the front of each manufacturers section again, to assist in the identification of the correct converter.
When you bolt it to the the flywheel, it will pull out the necessary amount. These guys are all right on the money. Convertor all the way back until the trans is bolted up. There should be a gap between the convertor and the flywheel before you bolt them together. After you bolt it up slide up and grab the lower blower pulley.
Stall Torque Ratio 2.01:1, Codes: 29530318, 29538348, 29538529, 29541293, 29543003 Numbers are on bar code labels next to mounting pads Year Engine Dia Hub SPL Pilot Mount Pilot Center To Bolt Center Stall 13 3/8″ 2.295 25 1.700 6 Pads 5 3/4″ 35-1BC
The new converters will also come with 12 bolts holes in the cover to help if you are running a big HP truck with a billet flexplate. Click to expand… I want to thank ATS for jumping in and helping me out so quickly.
Can a torque converter free wheel during trans installation?
NO RAGRETS!!! No, The converter has to be fully seated in the transmission pump and it has to line up with the flexplate during installation. The converter will not free wheel once the trans is installed. The best way to line it up as by index marks on the block and trans case.
Why is my torque converter not aligned with the flex plate?
I can barely move it with my finger, which is all I can get into the small hole to turn it. Any help is appreciated. I know you said everything is seated correctly…but if the converter is tight against the flex plate it sounds like the converter is Not seated all the way into the trans.
Where is the gap between the convertor and the flywheel?
There should be a gap between the convertor and the flywheel before you bolt them together. After you bolt it up slide up and grab the lower blower pulley. You should be albe to spin the engine and convertor by hand.
NO RAGRETS!!! No, The converter has to be fully seated in the transmission pump and it has to line up with the flexplate during installation. The converter will not free wheel once the trans is installed. The best way to line it up as by index marks on the block and trans case.
I can barely move it with my finger, which is all I can get into the small hole to turn it. Any help is appreciated. I know you said everything is seated correctly…but if the converter is tight against the flex plate it sounds like the converter is Not seated all the way into the trans.
There should be a gap between the convertor and the flywheel before you bolt them together. After you bolt it up slide up and grab the lower blower pulley. You should be albe to spin the engine and convertor by hand.
What happens when a torque converter is stuck?
Having a stuck torque converter and flywheel is very common with engines that have seized up, or that have thrown rods, or will otherwise not turn. It is very difficult to get a good grip on the flywheel when trying to get the things to rotate.
Can a torque converter line up with the flexplate?
No, The converter has to be fully seated in the transmission pump and it has to line up with the flexplate during installation. The converter will not free wheel once the trans is installed. The best way to line it up as by index marks on the block and trans case. It will get you close enough.
How big is the torque converter control bolt?
Application Spec Floorshift Control Bolt 89 in lb Flywheel to Torque Converter Bolt 46 ft lb Forward Accumulator Cover to Valve Body 6-10 ft lb Heat Shield to Transmission Bolt 13 ft lb
What’s the PSI of a torque converter bolt?
ARP Torque Converter bolts are rated at 200,000 psi and come with hardened parallel-ground washers, where applicable. Didn’t find the kit you were looking for? © 2006-2020 AUTOMOTIVE RACING PRODUCTS, INC. Older versions may have problems viewing some of the features of our site. Click the links above to download the most current browser.