How to check Yamaha motorcycle fault code DTC?

Error codes DTC of Yamaha Motorcycle. Explanation and Troubleshooting. To enter the diagnostic mode and check the existing error codes in memory, do the following: 1. Turn off the ignition, the engine stop button to put in the ON position. 2. Disconnect the fuel pump connector.

What is the error code on a Yamaha R1?

D: 61 = error sheet of the ignition module for sensors (00 = there are no errors in the memory, 11-70 = error codes for the components, if there are more than one error in the memory, they are displayed alternately)

How to check a Yamaha er-3 fault code?

Er-3 – it is impossible to consider the testimony from the ignition module; Login process in diagnostic mode: 1. Switch off ignition. Disable button Start / Stop Engine (red on the right panel). 2. Press both buttons on and keep them tidy. 3. Turn the ignition, hold the button after the ignition is about 8 seconds.

How to turn off the stop engine on a Yamaha R1?

Release the buttons, use the SELECT button to select “dIAG” (for the case if another text appears on the dashboard). After dIAG is displayed on the screen, press both buttons on the dashboard (SELECT + RESET) for ~ 2 seconds. After the diagnostic mode (d01) is displayed on the dashboard, turn off the stop engine button.

What does error code 39 Mean on Yamaha R1?

My bike started to stall and ended up cutting out. it had error code 39 up on it, when that happened. This means Injector: open circut detected, according to the manual.

Where do I find the error code on my Yamaha?

To clear the error from the system memory come on line d62 and includes buttons stop the engine on the right panel. When you enter the diagnostic mode, the display shows the cell [d01]. Press Select (top) need to go to the index [d60] (self-test in real time) and [d61] (memory error) and see the number next.

How to turn off diagnostic mode on a Yamaha?

Login process in diagnostic mode: 1. Switch off ignition. Disable button Start / Stop Engine (red on the right panel). 2. Press both buttons on and keep them tidy. 3. Turn the ignition, hold the button after the ignition is about 8 seconds. 4.

What is the fault code for a Yamaha motorcycle?

34 – faulty ignition coil cylinder 2 – self-diagnosed string D: 31; 35 – faulty ignition coil 3 cylinder – self diagnosed string D: 32; 36 – faulty ignition coil 4 cylinder – self diagnosed string D: 33;

What’s the Code 39 on a Yamaha R1?

IF the CEL comes on , Its code 39. Someome was recommeding me to check the plugs and or change them and also change the fuel filter , then read the post so want to start with ground up. Should i just eliminate the bazzaz and go from there ?

When is a fuel injector considered to be faulty?

Fuel injectors are deemed to be faulty if they do not operate as designed. Fuel injectors are considered to be clean if and when fuel delivery, atomization and distribution are within 1% of the design specification of that fuel injector. The injector cannot be recovered. We do not charge for the time spent on bad fuel injectors.

How to troubleshoot Yamaha Grizzly 700 starting problems?

While your starter problem might be something incredibly simple, you might need a new battery or a starter relay. Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference.

How to check the Diagnostic Code on a Yamaha Grizzly?

Diagnostic code number on display followed by checking method. • Fully closed position 15 ~ 20 Check with throttle fully closed. • Fully opened position 95 ~ 100 Check with throttle fully open. Pressure difference (atmospheric pressure and intake air pressure). Displays the intake air pressure. Set the engine stop switch to “RUN”, then

Where is the Kill Switch on a Yamaha Grizzly 700?

Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference. Make sure the kill switch on the left handlebar side is in the “Run” position. It might seem like a “no brainer,” but it’s actually a common oversight.

Navigation