Can a knock sensor cause a car ECM to fail?
There’s also a knock sensor on the engine itself. While these sensors aren’t likely to cause any catastrophic problems, failures in these areas can cause your ECM to make unnecessary adjustments that affect your car’s performance. In these cases, though, the problem is usually with the sensors, and not with the ECM.
What causes a Chevy Silverado brake to rattle?
If the guy whacked it with a hammer, etc. to get the rotor off he probably broke the e-brake shoe retainer clip. If he didn’t replace the clip, that would cause the ebrake shoe to rattle around inside the drum.
What are the most common problems with a GMC Sierra?
Another 258 people reported the second-biggest issue where heating and air conditioning temperature and air delivery mode door actuators may fail. If one or more delivery mode door actuators fail, the HVAC system may not produce correct temperatures or air delivery. The HVAC system stores fault codes, which help with diagnosis.
Is it safe to drive a 2003 Chevy Silverado?
I own a 2003 Silverado that has intermittent brake failure problems . The dealer has repaired this time and time again but the problem persists . The dealer and now GM say that this is a normal function for this vehicle , but now the brake pedal goes to the floor and although they are telling me it is safe to drive I am refusing .
Why does my Chevy Silverado belt keep squeaking?
Repetitive squeaking indicates the belt is not running true, and prolonged squealing means the belt is overheating. Both noises point to a bad A/C belt tensioner. With basic tools and little time, you can replace the tensioner in your Silverado quickly in the comfort of your own garage.
What to do if your serpentine belt is making a noise?
Belt noises can be diagnosed with a spray bottle of water. With the engine running and the sound audible, lightly mist the grooved side of the belt with water. If the noise disappears or lessens, but then shortly returns, the problem is probably a misaligned pulley.
Why does my car make a slipping belt noise?
Belt noise can be hard to isolate, as the sound may seem to be coming from an accessory drive, such as the alternator or air conditioning compressor. A noise that occurs only when the vehicle accelerates is likely to be a slipping belt, as is a noise that occurs only when the car is started cold.
Where is the a / C belt on a Chevy Silverado?
The Vortec 4.8, 5.3, and 6.0 liter engines have a main accessory drive belt for the water pump, power steering, and alternator. The air conditioning compressor is driven by a separate belt that is mounted low on the engine and behind the accessory belt.
What to do if your ECM power relay is failing?
For this reason, if you suspect that your ECM power relay may be having an issue, have the vehicle inspected by a professional technician, such as one from YourMechanic, to determine if the relay should be replaced. The most popular service booked by readers of this article is Vehicle Engine Electrical Inspection.
Why is the fuel pump and relay not working?
The ignition circuit, which includes the ignition switch, controls power to many components, including the fuel pump and relay. If there is an issue with the switch or the circuit, perhaps a wiring problem, then power to the fuel system may be cut off.
Can a new starter cause an ECM to fail?
Installing a new starter can also cause ECM failure. This is because they often bypass the surge protector on the ECM, leading to a power surge when you start the vehicle. The same thing can happen if you get your wires crossed while jumping your car. A failing battery can also cause ECM failure.
What happens if my PCM fails the emissions test?
This may cause you to fail your state’s emissions test. If your car does fail, check your PCM and ECM first. Believe it or not, a failed PCM or PCM may actually be good news: replacing either of these systems is significantly cheaper than getting a new catalytic converter.
What are the symptoms of a bad PCM relay?
These three symptoms indicate a bad PCM-relay: 1 You get no power when you insert the key. 2 The engine will not start. 3 You experience a massive battery drain or a dead battery.
How to diagnose a bad engine control module?
The best way to diagnose an engine control module fault is to understand its main responsibilities. Once you are aware of these primary functions, it becomes easier to determine what symptoms are bad PCM symptoms.
How does the PCM work with the fuel pressure sensor?
With the information that the PCM receives from the fuel pressure sensor, it will know the exact amount of fuel to give the engine. That way, the engine doesn’t receive too much or too little fuel. Instead, it receives just enough fuel to operate properly while lowering evaporative emissions.
What are the symptoms of a bad air fuel ratio sensor?
1. Decrease in fuel efficiency One of the first symptoms of a problem with an air-fuel ratio sensor is a decrease in fuel efficiency. The air-fuel ratio sensor monitors the oxygen content in the exhaust stream and sends data to the computer so that it can add or subtract fuel.
What are the symptoms of a bad mass air flow sensor?
3 Symptoms of a Bad Mass Air Flow Sensor. 1 Your Car Hesitates or Suddenly Jerks Forward While Accelerating. A bad MAF sensor can cause your vehicle to experience poor drivability issues such as 2 Your Air Fuel Ratio is Too Rich. 3 Your Air Fuel Ratio is Too Lean. 4 Your OBD-II Scanner Gets Code P0101.
How often does the PCM monitor the oxygen sensor?
The PCM monitors the oxygen sensor heater circuits for both voltage and current. On most models, the voltage monitor runs continuously and the current monitor runs at least once per drive cycle after specific enabling criteria are met.
What happens when the throttle position sensor fails?
The throttle position sensor can fail in several ways, all of which result in poor fuel economy at best, and performance limitations that may create safety hazard for you and other motorists at worst. This sensor can fail gradually, or all at once. In most cases, the Check Engine Light is illuminated if a TPS failure is detected.
What’s the problem with the Mitsubishi Eclipse Spyder?
Hinim having the same problem but mynback windoes went down but now they wont go back up can some one help 4 people found this helpful. There is a button on the drivers door panel that when pushed keeps the rear windows from rolling back up. 1 people found this helpful. Are we Talking about a 2007 Mitsubishi Eclipse Spyder GT.
Where is the knock sensor on the engine?
The knock sensor is located on the engine block, cylinder head or intake manifold. This is because its function is to sense vibrations caused by engine knock or detonation. The PCM uses this signal to alter the ignition timing and prevent detonation.
What happens if the crankshaft position sensor fails?
If the crankshaft sensor has failed completely, and isn’t sending a signal to the ECU at all, then the computer won’t send any fuel to the injectors. This will leave you unable to start the car. A failing or failed crankshaft position sensor may cause the check engine light on your dashboard to come on.
What is the diagnostic code for a Nissan check engine light?
Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s). Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code listfor definitions on all other Nissan diagnostic trouble codes. Manufacturer Specific Codes P1105MAP/BARO Pressure Switch Solenoid Valve
There’s also a knock sensor on the engine itself. While these sensors aren’t likely to cause any catastrophic problems, failures in these areas can cause your ECM to make unnecessary adjustments that affect your car’s performance. In these cases, though, the problem is usually with the sensors, and not with the ECM.
How does a bad ECM affect fuel economy?
Poor Fuel Economy. A faulty ECM disallows your engine from knowing how much fuel to burn in the combustion process. Typically, the vehicle consumes more fuel than it should in this situation. You’ll end up paying more for gas than you would with a functioning ECM. The ECM plays a vital role in engine performance.
What are the symptoms of an ECM failure?
Nowadays, those functions are controlled by three computers: Transmission control module (TCM). Today, we’re going to take a look at the most common signs of ECM failure. These ECM failure symptoms can be your first warning of serious engine trouble, so it’s important not to take them lightly.
Installing a new starter can also cause ECM failure. This is because they often bypass the surge protector on the ECM, leading to a power surge when you start the vehicle. The same thing can happen if you get your wires crossed while jumping your car. A failing battery can also cause ECM failure.
https://www.youtube.com/watch?v=A2P93bGrUVw