Why does my 1997 Pontiac Grand Am Not turn off?

This 1997 Pontiac Grand Am came in with the complaint that the ignition switch will not turn all of the way off. This causes two other problems. The key cannot be removed from the ignition lock cylinder and the ignition stays on enough for the systems not to shut down fully. The battery will go dead as a result.

How can I get a new ignition key for my Pontiac Grand Am?

Order a new ignition/key online and have a mechanic or locksmith install and code it for you (if necessary). A word of caution: The type of key you need depends on the year and model of your Pontiac Grand Am. Therefore, the options for getting a new key made and programmed depends on whether you need a transponder or a regular key.

When did the Pontiac Grand Am Come Out?

The Pontiac Grand Am was introduced in 1973. This model has six types of keys. Non-Transponder Keys: 1985 to 2005. Please keep in mind that while some keys or keys may look the same, they have different capabilities/frequencies/keyways. Therefore, having the right key is essential.

Do you have the same key on your Grand Am?

Please keep in mind that while some keys or keys may look the same, they have different capabilities/frequencies/keyways. Therefore, having the right key is essential. Click on the type of key you had or your year model below to get the most accurate information:

What to do if your ignition key won’t turn?

This feature is not available right now. Please try again later. Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Loading…

What causes a car key to not turn over?

This can trap a piece of the key inside the cylinder, causing more damage. Also known as a key cylinder, the ignition lock cylinder is another area that could be causing issues with a key turning over. Below are the two most common problems associated with the ignition lock cylinder and the key not turning.

Why does my Gm key not turn in?

The GM (Buick, Cadillac, Chevy, GMC, Hummer, Oldsmobile, Pontiac) ignitions tend to fail because of wear from inserting the key at a slight angle. This is the same for the Chrysler vehicles (Chrysler, Dodge, Eagle, Jeep, Plymouth).

Why does my Toyota Geo not turn on?

The Toyota and Geo ignitions tend to stop turning because of worn keys. A new “code” key or duplicate key may solve the problem. If a new key does not get your ignition to turn then your ignition will need to be worked on. Vehicles Affected

What happens when your key won’t turn in?

If your key won’t turn your ignition lock cylinder and the steps above did not get your ignition to turn, then there is an extremely good chance your vehicle is in the list below. The list below is just a partial list of vehicles we suspect of having ignition failure problems when people call and say “My key won’t turn in my ignition”.

What kind of car won’t turn on?

Ford vehicles such as Focus, Contour, Cougar and Mystique tend to stop turning because of ignition wear, all other Ford vehicles tend to be dirty ignitions or locked steering wheels. Vehicles Affected We understand the list below will have some errors, but we will do our best to make this list as accurate as possible.

What to do if your Grand Am won’t start?

When your Grand Am turns over but won’t start it maybe your anti-theft security system. When the security light blinks, the car won’t start. You must do a simple reset. The procedure in this video is what worked for us. Use of the free information in this video is at your own risk.

Can you replace the PCM on a Pontiac Grand Am?

Installing a PCM (power-train control module) is not a difficult task and can be done by almost anyone. If you have been told your Pontiac Grand Am has a faulty PCM and want to replace it yourself, it’s a simple process.

When was the last year the Pontiac Grand Am was made?

The Grand Am had two separate three-year runs in the 1970s: from 1973 to 1975, and again from 1978 to 1980. It was based on the GM A platform. Production of the Grand Am was canceled in 1980 when it was replaced by the Pontiac 6000. The Grand Am was reintroduced in 1985 when it replaced the Pontiac Phoenix.

What kind of suspension does a Pontiac Grand Am have?

Additionally, Grand Ams featured a Radial Tuned Suspension (RTS) as standard equipment that included radial-ply tires, Pliacell shock absorbers, and front and rear sway bars. The springs were advertised as being computer selected.

What was the compression ratio of the Pontiac Grand Am?

Engines were also detuned to meet the 1975 emission regulations with the compression ratio dropping to a new low of 7.6 to 1 on some engines.

What to do when your steering wheel won’t turn in?

When you feel the steering wheel wanting to spring back you have turned hard enough, do not turn the wheel too hard, turn the key with normal pressure (Do not force key). If a locked steering wheel is the problem this will fix it. Back to Troubleshooting

What causes a key to get stuck in the steering wheel?

Component 1: Steering wheel. In many vehicles, removing the key locks the steering wheel from turning. Occasionally, because of this lock, the steering wheel can get stuck, which in turn means the vehicle key also becomes stuck and cannot move to release it.

What should I do if my ignition key won’t turn?

Average rating from 41 customers who received a Ignition key does not turn Inspection. It can be frustrating when you insert your key into your car’s ignition and it refuses to turn. Your mind races with all the possibilities of what could be going wrong, but luckily, most ignition key issues are not only common, but also quick to fix.

Where is the fuel pump relay on a Pontiac Grand Am?

The fuel pump relay is #18 in the fuse box. Start with the car off, and have somebody else put the key in the cars ignition and attempt to start the car while you listen to the relay. If you can hear this relay make a “clicking” noise as the car attempts to start, then it is working properly.

What kind of car is the Pontiac Grand Am?

The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. 2003 Grand Am will not start.

Vehicles Affected The Toyota and Geo ignitions tend to stop turning because of worn keys. A new “code” key or duplicate key may solve the problem. If a new key does not get your ignition to turn then your ignition will need to be worked on.

What happens if you don’t have the ignition key?

In addition, the ignition switch plays a role; in keeping your car from getting stolen. Consequently, without the key, the switch won’t move to the start or run positions, and will lock the steering wheel. OFF – Or LOCK position – Turns off power to the engine and electrical accessories

What are the signs of a failing ignition switch?

Common Signs of a Failing Ignition Switch Engine Will Not Start. The problem here is probably: An anti-theft fault; Fault in the fuel pump circuit; Ignition circuit; Engine computer; If the anti-theft light is flashing, the computer is NOT recognizing the key or key fob and is; preventing the engine from starting.

Why is my car not turning on when I Turn on the ignition?

Of course, if you access the car itself with your key, you likely won’t be able to turn on the ignition because of all those extra tumblers. And on the off chance that you do turn the ignition cylinder, the immobilizer won’t allow you to start the car, because it’s protected by one-in-millions of transponder codes.

What to do if your ignition key won’t work?

In this case the ignition lock must be replaced. Step 7 – In extreme conditions such as high mileage or a key chain adorned with many ornaments can wear the tumbler which causes the key not to work. If the door key is same as the ignition key, the door tumbler can be removed and a key made if no security chip is installed, (older cars).

What happens if you break the ignition lock?

The key slides into the ignition lock cylinder. These two components mate together and essentially become one. So if either of them break, they will both be affected. In addition, there are many other small moving parts inside your steering column that are activated when you insert the key and turn it.

What does it mean when the key won’t come out?

What I mean is you can change the gears without pushing the button on the side of the gear shifter so I didn’t know if this may be the problem since the key won’t cut off or come out if the car is not in park. My car has 999999 miles. My car has an automatic transmission. It is either the ignition switch electrical or the ignition lock cylinder.

What causes an engine to stall at idle?

If the ISC valve is gummed up with fuel varnish or dirt, it may stick, preventing the engine from maintaining the proper idle speed when the throttle closes. A faulty idle speed control circuit may also allow the engine to stall when idling if it fails to compensate for idle loads placed on the engine by the charging system or A/C compressor.

Is there check engine light for intermittent stalling?

Many times, there will be no check engine light and no fault codes to give you a clue as to what might be causing the engine to stall. So the trick to diagnosing an intermittent stalling problem is to catch the vehicle when it’s acting up — and that rarely happens when you have the vehicle in your shop.

What happens if you have a bad idle control valve?

Since the idle air control valve is supposed to manage the idle speed of the engine, a bad valve will certainly throw that out of whack. It will cause the idle speed to randomly fluctuate to different speeds rather than stay at one constant speed. The idle speed may be too high at one moment and then too low at other moments.

Why does my car key not turn in the ignition?

A very common reason a car key won’t turn in the ignition is that the keyway of the ignition cylinder is a little jammed up. Just lubricating the lock may be enough to solve your issue. You will say that WD40 is often the go-to example for lubrication of any kind, but I would not recommend it in this case.

Why does my steering wheel not turn when I turn the key?

Turn the Steering Wheel The most common reason that a car key will not turn is that the steering wheel has locked. This will happen when the steering wheel has been moved after the key has been removed from the ignition cylinder. Turn the steering wheel to the right and left.

How do you change the ignition on a car?

Find the locking pin on your ignition assembly. Use a tool of the correct size to depress the lock pin. Pull the old ignition cylinder lose. You might need to shake the ignition cylinder loose or finesse it out of its housing. Insert your new key into the new ignition cylinder. Fit the new ignition cylinder into the housing.

What to do if your ignition switch won’t work?

Step 7 – In extreme conditions such as high mileage or a key chain adorned with many ornaments can wear the tumbler which causes the key not to work. If the door key is same as the ignition key, the door tumbler can be removed and a key made if no security chip is installed, (older cars).

How can I Turn Off the ignition without a key?

Be sure to make the hole large enough for you to insert your screwdriver, and drill to the back of the key slot. Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right.

Where is the ignition switch on a car?

These switches are located just to the side of the steering wheel and column on your dashboard, and are one of the main components in your car’s starter system. If the switch is not working, you will likely have to remove and replace it.

How to remove skim key from Jeep Grand Cherokee?

JEEP SKIM KEY PROBLEM… SOLVED!!!! ECM REPROGRAMMED Jeep Grand Cherokee. Remove SKIM from ECM If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What should I do if my car won’t turn off?

With the ignition turned off and the car continuing to run, simply remove the plug from the alternator (DO NOT TRY AND REMOVE THE BATTERY POWER WIRE FROM THE POWER STUD!) and the car should shut off if the alternator is creating the problem.

Why does my car run when the ignition is turned off?

Why does my Saturn key not turn in?

The Saturn ignitions tend to stop turning because of worn keys and worn ignitions. (mostly worn ignitions) Vehicles Affected The GM (Buick, Cadillac, Chevy, GMC, Hummer, Oldsmobile, Pontiac) ignitions tend to fail because of wear from inserting the key at a slight angle.

What was the problem with the GM ignition switch?

The GM ignition switch defect allegedly stemmed from an issue with the switch circuitry which causes ignitions to switch from the “on” position to either the “standby” or “auxiliary position.” As a result, the vehicles allegedly turn off and the air bags become deactivated.

How can I find out if I am part of the GM ignition switch settlement?

Consumers can check their eligibility through the settlement website’s VIN lookup. Cash payments of varying sizes. Individuals affected by the GM ignition switch issue and key rotation issue will receive larger payments than individuals covered by the other recalls, although exact payment amounts will depend on the number of claims filed.

How do you remove ignition switch from car?

Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right. Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position.

How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?

This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.

Where is the ignition switch on a GM PassLock?

Pull the radio out of it’s cavity. Disconnect the wiring connector and the antenna wire, and set the radio aside. On the left side of the radio cavity, there will be an opening, through which you will be able to see the Ignition Switch.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

How to make a link GM passkey no start bypass?

HERE IS THE LINK GM Passkey NO start Bypass Cut two terminals off the end of the terminal strip. Set the rest of the terminal strip aside. Takle one of the 2200 ohm resistors and bend the leads as I’m doing here. Then cut off the excess lead wire. (The color code for the resistor is three red bands.)

What to do if your car key won’t turn in?

Ignitions can be extremely fragile. Please do not poke around inside the ignition lock cylinder. A dirty ignition can be fixed by spraying small doses of an electrical cleaner in the ignition then gently sliding the key in and out of the ignition cylinder many times.

How to replace GM PassLock ignition key lock cylinder?

Press the small release tab (see pictures) While turning key to the ON Position Installation is the reverse of the above procedures, see below for the relearn procedure Clear all Diagnostic Trouble Codes (DTC). Record and/or repair your DTCs before clearing. You can clear the codes by disconnecting the battery for 10 minutes.

Where is the electronic ignition switch located on a GM car?

A typical symptom of failure is the security light illuminating on the dash. Also, keep in mind the electronic ignition switch is located just behind the lock cylinder. It is the plastic part that the ignition lock cylinder fits into. It contains the actual electrical connections and wiring and it sends current to numerous different components.

Please do not poke around inside the ignition lock cylinder. A dirty ignition can be fixed by spraying small doses of an electrical cleaner in the ignition then gently sliding the key in and out of the ignition cylinder many times. ( DO NOT use this method on Honda, Acura, Toyota or any vehicle that uses a high security key ).

Why does my car not start when I Turn on the key?

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

How to troubleshoot a car that won’t turn off?

Hook up your tachometer according to instructions and check the idle speed. Most four and six cylinder engines should idle around 850 to 900 RPM. Eight cylinder engines may idle around 600. Check your workshop manual and adjust the idle speed according to the specifications. Step 3: Check the anti dieseling solenoid.

Navigation