What happens when you get a trouble code p0341?
A P0341 trouble code will generally trigger the check engine light on. Depending on your vehicle’s make, the check engine light may be referred to as the CEL, the Malfunction Indicator Lamp (MIL) or Service Engine Soon (SES) light.
Why does my Honda Accord p1009 have p0341?
Sometimes P0341 can happen at the same time as P1009. The strainer is somewhere close to the PS pump because Honda indicates removal of the pump and tensioner to access he strainer. Sorry but I’ve never had it off myself but the pic I have shows a small plate held on to the engine with 2 bolts. Hope that helps a bit.
Can a p1009 happen at the same time as p0341?
Sometimes P0341 can happen at the same time as P1009. The strainer is somewhere close to the PS pump because Honda indicates removal of the pump and tensioner to access he strainer. Sorry but I’ve never had it off myself but the pic I have shows a small plate held on to the engine with 2 bolts.
How to check for a Honda p1009 code?
1. Turn the ignition switch ON (II). 2. Clear the DTC with the HDS. 3. Start the engine. 4. Check for Temporary DTCs or DTCs with the HDS. Is DTC P1009 indicated? YES – Go to step 5. NO – Intermittent failure, system is OK at this time. 5. Turn the ignition switch OFF. 6. Remove the power steering pump and auto-tensioner. 7.
A P0341 trouble code will generally trigger the check engine light on. Depending on your vehicle’s make, the check engine light may be referred to as the CEL, the Malfunction Indicator Lamp (MIL) or Service Engine Soon (SES) light.
What causes a Honda engine to set the p1009 code?
A stretched timing chain or damaged tensioner can also set the P1009 code. Before replacing the timing chain or tensioner, check engine oil level and condition. Replaced engine oil and filter with the factory recommended oil weight if necessary.
Why does my engine have a trouble code?
NOTE: In some cases this engine code is generated on vehicles that do not actually have a camshaft position sensor. In those cases it basically means the engine is misfiring badly due to faulty spark plugs, spark plug wires, and often coils. Often relacing the sensor fixes this code, but not necessarily.
How much does it cost to repair a p1009 Honda?
The cost of diagnosing the P1009 HONDA code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
What is the code for check engine light?
This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. Our certified mobile mechanics can come to your home or office to perform the Check Engine Light diagnostic for $0.0 .
When does the cam code 341 come back?
The egr and maf codes are gone, but the cam code 341 still comes back after about 5-8 miles when the car stumbles and gags, it then recovers for a sho… My Camry dies after 20 minutes of driving and then has to sit for a half hour or so before it can start up again.
What does a p0303 fire code tell you?
A P0303 code, for example, would tell you that the No. 3 cylinder is misfiring. To figure out which cylinder is No. 3, refer to a diagram of the engine’s firing order or look for markings on the intake manifold, spark plug wires or ignition coils (if the engine has a coil-on-plug ignition system).
What does a flashing check engine light mean?
A flashing check engine light and a P0301 to P0312 diagnostic trouble code (DTC) is a surefire indication that one or more cylinders are misfiring. Occasional misfires may pass unnoticed, but a steady misfire is hard to miss. The engine usually feels rough, lacks power and uses more gas than usual. Sometimes a misfire may feel like a vibration.
What is the diagnostic code for a misfire?
Misfires that turn on the check engine light and log a cylinder-specific fault code are the easiest to diagnose. A flashing check engine light and a P0301 to P0312 diagnostic trouble code (DTC) is a surefire indication that one or more cylinders are misfiring. Occasional misfires may pass unnoticed, but a steady misfire is hard to miss.