Are there rear struts on a Honda Civic?
There is no need to worry about the rear as there are not actual “struts” mounted for the rear wheels, only a straight axle, coil springs and shocks. Be careful to mount the new struts in place exactly as the old ones were. It can be helpful to mark bolt locations with a wax pencil to make sure you remount them correctly.
How do you replace shocks on a Honda Civic?
Remove the 14mm pinch bolt from the damper. Locate the two damper fork bolts that connect the damper fork to the lower control arm. With your socket and ratchet, remove the two 17mm damper fork bolts. Pull down on the damper fork, and away from the bottom strut. Repeat this step on the other side.
How do you remove a strut from a car?
Pull the wheel off and then use the socket wrench to remove the lower mounting nut on the bottom of the A-arm. Pop the hood of the car and use the socket wrenches to remove the mounting bolts for the top of the strut in the corner of the engine compartment above the A-Arm. Slide the old strut out of the bottom of the A-arm and set it aside.
How do you attach a strut to a floor?
Place the bottom strut into the damper fork, and secure it with the damper pinch bolt. Connect the damper fork to the lower control arm using the damper fork bolts. You may need the floor jack to raise the control arm to line up the bolt holes. Repeat this step on the other side.
Remove the 14mm pinch bolt from the damper. Locate the two damper fork bolts that connect the damper fork to the lower control arm. With your socket and ratchet, remove the two 17mm damper fork bolts. Pull down on the damper fork, and away from the bottom strut. Repeat this step on the other side.
How do you remove the top of a strut?
Place the spring compressor tool on each end of the spring. Compress the spring to where it is no longer holding up the strut top. Use a 5mm Allen wrench to hold the shaft in place. Then, use a 14mm wrench to remove the top nut, and pull the strut top off. Carefully and slowly decompress the old spring.
Place the bottom strut into the damper fork, and secure it with the damper pinch bolt. Connect the damper fork to the lower control arm using the damper fork bolts. You may need the floor jack to raise the control arm to line up the bolt holes. Repeat this step on the other side.
How to install a lower strut on a car?
TWO LOWER BOLTS STYLE: • (Fig. 4) Remove and save lower mounting nuts (G) and bolts (H). Separate lower strut mount from steering knuckle. • (Fig. 1) Remove and save the bearing plate upper mounting nuts (A). (P-Pack included with new nuts.) • Remove the strut assembly from vehicle (Fig. 5, 6 & 7).
When to replace a top shock mount on a car?
Top strut mounts and upper shock mounts: when to replace? In a car, a strut is a shock absorber that is built into an assembly with the coil spring and the top mount, called a strut mount, see the illustration. A top strut mount connects the strut to the vehicle’s body or frame. Strut mount in a MacPherson strut.
When do you need to replace a strut mount?
Strut mounts are also replaced if they show excessive corrosion or if the visible rubber part looks ripped or badly worn. Rear strut mounts, for example, are often replaced because of rust damage. Is it safe to drive with a bad strut mount?
Where does the top strut mount go on a car?
A top strut mount connects the strut to the vehicle’s body or frame. Strut mount in a MacPherson strut. In many cars, you can see the front top strut mounts under the hood (see photo below).
Top strut mounts and upper shock mounts: when to replace? In a car, a strut is a shock absorber that is built into an assembly with the coil spring and the top mount, called a strut mount, see the illustration. A top strut mount connects the strut to the vehicle’s body or frame. Strut mount in a MacPherson strut.
Where are the shock mounts on a MacPherson strut?
A top strut mount connects the strut to the vehicle’s body or frame. Strut mount in a MacPherson strut. In many cars, you can see the front top strut mounts under the hood (see photo below). Shock absorber mounts serve the same purpose, scroll down to read more about them.
How do you install a new strut on a car?
Installing a New Strut Install the completed strut assembly back into the steering knuckle. Replace the bolts, leaving them finger tight, allowing the assembly to move freely. Place the strut assembly back into the strut tower and replace the strut tower bolts.
What happens if you remove the center nut on a strut?
Do not remove the center nut or the strut will come apart and it is under high spring tension. Since you’ve removed the bolts from the steering knuckle, the strut might fall loose after you remove these bolts. It might help to have a partner holding onto the strut assembly while you loosen these bolts.
There is no need to worry about the rear as there are not actual “struts” mounted for the rear wheels, only a straight axle, coil springs and shocks. Be careful to mount the new struts in place exactly as the old ones were. It can be helpful to mark bolt locations with a wax pencil to make sure you remount them correctly.
What kind of shocks do Honda Civic 2001 have?
Honda Civic 2001, Bare Strut by FCS®. FCS bare shocks and struts are engineered to restore your vehicle’s handling and control. Shocks, struts, and cartridges are a great option to restore OE performance and normal driving conditions. Honda Civic 2001, Speedy Strut™ New Twin-Tube Non-Adjustable Complete Strut Assemblies by SenSen®.
Installing a New Strut Install the completed strut assembly back into the steering knuckle. Replace the bolts, leaving them finger tight, allowing the assembly to move freely. Place the strut assembly back into the strut tower and replace the strut tower bolts.
Where are the strut bolts located on a car?
Once the strut bolts are out the strut and steering knuckle are separated. Open the hood and locate the strut towers to remove the bolts. Usually they are located at the midpoint of the inside fender well and look like cylinders. They are most likely held in by three small bolts. Remove the strut tower bolts.