What axles came in a YJ?
Identifying the axles in YJs is pretty simple since there were no options for it. Every YJ came with a Dana 30 up front and a Dana 35 in the rear. TJ Wranglers will have either a Dana 30 in the front and a Dana 35 in the rear unless you have a Rubicon model. In which case you’ll have 44s front and back.
What year jeeps came with Dana 44 axles?
In 2003, the highly anticipated Jeep Wrangler Rubicon rolled onto the scene with Dana 44 axles equipped with selectable air lockers. Though the TJ Dana 44s had advantages over the anemic Dana 30 and 35, it wasn’t until the 2007 release of the Jeep Wrangler JK that the Dana 44 as we knew it was all but reinvented.
What vehicles have a Dana 30 front axle?
Comanche, Cherokee, and Grand Cherokee Dana 30 The Comanche (MJ) and Cherokee (XJ) use a reverse cut Dana 30 and the Grand Cherokee (ZJ) uses a normal cut Dana 30. Like the YJ and the TJ, these axles use a 5 on 4.5″ wheel bolt pattern. All of these trucks use coil springs up front.
What vehicles have a Dana 35 front axle?
General specifications. The Dana 35 (as well as the AMC-15) is found in a wide variety of vehicles. The most common Dana 35 applications are as a rear axle in the Jeep Cherokee, Jeep Wrangler, and Jeep Comanche and as a front axle in the Ford Explorer and Ford Ranger.
What is the difference between Dana 30 and 44?
The only difference between the JK Dana 30 and Dana 44 is ring gear size, electronic locker, and bigger shafts. You’re better off just starting with an aftermarket Dana 44 that is a “true 44”.
How do you tell if you have a Dana 35 or 44?
The easiest way to tell these axles apart is to look at the shape of the differential cover. The Dana 35 cover is pretty much perfectly round. The Dana 44 is sort of a six-sided shape. A Dana 35 (left) compared to a Dana 44 (right).
How do I identify my Dana axle?
To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.
What’s the difference between YJ and Dana 30 axles?
The Dana 30 gear ratios are either 3.21 or 3.73. The width of the axle shafts is 1.13 inches. The YJ Dana 30 hold a reverse cut ring and pinion, but the TJs do not. Both TJs and YJs, however, use a 5×4.5 inch bolt pattern.
What’s the best axle for a Jeep Wrangler YJ?
Ten Factory MG22131 Front 30 Spline Chromoly Axle Kit for 84-95 Jeep Wrangler YJ & Cherokee with Dana 30 Axle – AFTERMARKET UPGRADE! Ten Factory MG22145 Front 27 Spline (Disconnect Eliminator) Chromoly Axle Kit for 87-95 Jeep Wrangler YJ and 84-92 Cherokee XJ with Dana 30 Axle – AFTERMARKET UPGRADE!
Why do Jeep YJ axles and hubs fail?
Because they are not designed for uneven and unpaved terrain, Jeep Wrangler YJ axle and hubs are far more likely to fail if they are the original stock parts. Replacing them with axel shafts that were designed to handle the rigors of the trail can save you a fortune in future repairs.
What is the width of a Chevy YJ?
Width: 58″ front, 58.25″ or 58.5″ rear — 2-2.5″ narrower than a YJ. That’s not a big problem in the rear (other than off-camber stability), but it’ll reduce turning radius up front. Less wheel backspacing compensates for this. Brakes: 11″ rear drums. What size front? Rear hard line junction is on opposite side of axle from YJ.