What does the p0341 code on a Volkswagen mean?
This P0341 Volkswagen code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor.
How to fix and clear OBD-II trouble code p0341?
Often replacing the camshaft sensor fixes trouble code P0341, however it is important to check the following first: Inspect the wiring at the camshaft sensor for melting or marks of corrosion Inspect the camshaft reluctor wheel for missing or damaged teeth.
What is the OBD code for a VW?
OBD2 Code P0341 Volkswagen definition: This P0341 Volkswagen code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor.
Why does my engine have a trouble code?
NOTE: In some cases this engine code is generated on vehicles that do not actually have a camshaft position sensor. In those cases it basically means the engine is misfiring badly due to faulty spark plugs, spark plug wires, and often coils. Often relacing the sensor fixes this code, but not necessarily.
What is the diagnostic code for Camshaft Position Sensor?
Cost of diagnosing the P0341 code P0341 is a diagnostic trouble code (DTC) for “Camshaft Position Sensor Circuit Range/Performance”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
When does the cam code 341 come back?
The egr and maf codes are gone, but the cam code 341 still comes back after about 5-8 miles when the car stumbles and gags, it then recovers for a sho… My Camry dies after 20 minutes of driving and then has to sit for a half hour or so before it can start up again.
What causes a p0341 DTC on a Mustang GT?
Ford Trucks / Mustang GT – An alternator phase problem, such as a blown diode or open coil, may cause so much electrical interference that the CMP signal gets distorted, causing a P0341 / P0346 DTC to set, among others, in spite of there being no actual problem with the CMP sensor or wiring.
What does DTC p0346 stand for in V8 engine?
On the other hand, V6 or V8 engines have two banks, Bank 1 and Bank 2, and would therefore have two CMPs, so DTC P0346 would refer to Bank 2. Sensor A indicates that the malfunction is occurring with the camshaft position sensor circuit that pertains to the intake camshaft.
Why is my DTC p0341 CMP sensor not working?
Depending on year, make, and model, DTC P0341 or P0346 may have number of causes. Here are some of the most common. Faulty Sensor – If the sensor coil is open or shorted, then it will generate no signal. Poor Installation – A good CMP signal is highly dependent on placement.
https://www.youtube.com/watch?v=NcCGc9878Ts
What does DTC stand for on OBD-2?
This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model. This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal.
What does the camshaft position sensor do on a Jetta?
In fact, it was rated the 11th most common automotive repair by CarMD’s recent Vehicle Health Index. This sensor is responsible for monitoring the camshaft’s position and relaying the information to the electronic control module, which then uses the data to instruct the coils to ignite the spark plugs at the right time.
Is the intake camshaft position sensor faulty?
Camshaft Position Sensor (G40) faulty Check Wiring from/to Camshaft Position Sensor (G40) Check Camshaft Position Sensor (G40) TT 01-15-08 for information about the intake camshaft, adjuster bridge and spool valve.
What does the camshaft position sensor signal mean?
The camshaft position sensor signal sent to the Engine Control Module (ECM) during the first few seconds of engine cranking is out of range. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning.
How much does it cost to diagnose a p0340 code?
The cost of diagnosing the P0340 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
Is there a p0340 camshaft position sensor replacement?
Code P0725 / P0335 / P0340 – Camshaft Positioning Sensor Replacement – Nissan Altima. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
How much does it cost to diagnose a p0343 code?
The cost of diagnosing the P0343 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0343 code detected?
What does the camshaft position sensor p0343 do?
P0343 Meaning The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module (ECM) to control ignition and fuel injection.