How do you reset the service light on a Volvo S70?

How do you reset the service light on a Volvo S70?

Press the trip odometer button in and hold it. Turn the ignition key to position “II.” Wait about 5 seconds until the service engine light begins to blink. After the 4th blink, turn the ignition key back to position “I.”

How do I clear the service message on my Volvo V70?

Press and hold the trip computer while turning your key to position two. The center arrow will flash red three times. On the third flash, you will let go and an alert will note that you just reset your service light.

How do I reset the service reminder light?

A code number for resetting the service reminder light is 1-5-1. To do this, press the test button once and release it And LED illuminates again. Then press 5 times and wait for the LED to illuminate. Press the button once and LED should flashes several times in succession and the reminder should have been reset.

How to reset service reminder light on Volvo 850?

Press the button on the diagnostic unit 4 times, briefly but firmly. Then the LED illuminates and stays illuminated, and the system is ready to accept manual code input. A code number for resetting the service reminder light is 1-5-1. To do this, press the test button once and release it And LED illuminates again.

What happens when you reset the SRL lamp?

When the TRIP METER RESET button has been pressed for 10 seconds, the SRL lamp starts to flash. Release the TRIP METER RESET button within 5 seconds. The instrument produces a sound when resetting has been done successfully. Turn the ignition off and then start the engine to verify the indicator has been reset.”

Step 1: Press and hold the odometer reset button. Step 2: Turn key to position II, without releasing the odometer reset button. Step 3: After a few seconds the Service light will flash. When this happens, release the odometer reset button. Step 4: Turn back the key to position 0.

How do you reset the trip meter on a Volvo S60?

Step 1. Confirm that you have the trip computer in T-1 mode; Step 2. Put the car key, and turn the ignition to position I ; Step 3. Press and hold trip meter reset button until the trip meter reads “0.0”. Do not release trip meter reset button; Step 4.

When did the Volvo S70 get an oil change?

This procedure applies to the Volvo S70, V70, and C70 between the years 1998 to 2000. This will light will illuminate in certain intervals to alert the driver that the vehicle is in need of an oil change. This particular vehicle I am working with here today is a 2000 Volvo S70. Thank you to all those who watch my videos and support my content.

How to reset engine system service required message?

I have discovered how to reset/clear the text message “Engine System Service Required” and orange triangle. Trip meter T1 and T2 were showing 0.7 miles. Hold down the trip meter reset button. Turn the ignition key on to position 2. Keep holding the trip meter button until the message and orange triangle go off.

How to disable day time running Volvo lights?

Hello, before cutting wires to disable your day-time running Volvo lights on Canadian model 850s, take the control knob out of the dash and look on the back, there was a white sliding switch there that allowed me to control my DRLs without having to cut anything. MVS Forum Member lud adds:

Step 1. Confirm that you have the trip computer in T-1 mode; Step 2. Put the car key, and turn the ignition to position I ; Step 3. Press and hold trip meter reset button until the trip meter reads “0.0”. Do not release trip meter reset button; Step 4. With the trip meter reset button still pressed, turn the key to position “II”; Step 5.

Where is the diagnostic connector on a Volvo V70?

The diagnostic connector is located in the center console, in front of shift lever. Turn ignition off. Press in trip odometer reset button. Switch ignition on, while continuing to press the trip odometer reset button. Continue pressing in the reset button for 10 seconds.

How to reset the SRL lamp on a Volvo 850?

Press in trip meter RESET button. Turn ignition to position II. When the TRIP METER RESET button has been pressed for 10 seconds, the SRL lamp starts to flash. Release the TRIP METER RESET button within 5 seconds. The instrument produces a sound when resetting has been done successfully.

How do you reset the odometer on a Volvo?

1. Turn ignition to position I 2. Press and hold in the reset button for the trip odometer 3. Turn the key to position II within 2 seconds, while continuing to press the trip odometer reset button. 4. For all vehicles, from the 2003 model year, a general yellow lamp will light when the reset button must be released.

How to reset Volvo time for regular service?

Insert key in to ignition but don’t turn it yet, POS 0. The service reminder indicator lamp illuminates for 120 seconds when the ignition is first switched on. Release the reset button for the trip odometer within 5 seconds. The instrument gives an audible signal when successful.

Is there a way to reset the service light?

If you’ve done the maintenance work and now want to reset the light, follow these instructions: Step 1. Confirm that you have the trip computer in T-1 mode; Step 2. Put the car key, and turn the ignition to position I ; Step 3. Press and hold trip meter reset button until the trip meter reads “0.0”. Do not release trip meter reset button; Step 4.

What should I do if my Volvo odometer does not reset?

If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset. The trip odometer must have at least 0.1 mile on it or the light will not reset. Keep the odometer reset button held in and watch the instrument cluster for the general warning indicator (I) to illuminate.

How do I reset the computer on a Volvo?

Open the hood of your Volvo and loosen the retaining nut on the cable clamp running to the negative battery terminal using a socket wrench. Slide the cable clamp off the negative battery terminal. Wait five seconds and reconnect the cable clamp. Tighten the retaining nut on the clamp using a socket wrench.