What is the Diag for a 2005 International 4300?
I Have a 2005 international 4300. Active code of 368 FMI 7, EGR driver mod./ECM2 comm. fault. The engine starts and runs, no power. What is the diag. procedure for this? Where is the EGR module located? Submitted: 7 years ago. Category: Medium and Heavy Trucks Andy : Hi there ! My name is XXXXX XXXXX I would like to try and help if I can !
When to set DTC 368 on EGR drive?
The EGR drive module constantly monitors the EGR actuator. When an EGR control error is detected, the EGR drive module sends a message to the ECM, a DTC is set, and the amber ENGINE lamp is illuminated. DTC 368 is set by the ECM when CAN 2 datalink communications are not received from EGR drive module.
What are the trouble codes for International trucks?
International Trucks Diagnostics Trouble Codes (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar
What’s the code for a DT 466E diesel truck?
We got couple of 05 International truck that has VGT problem. Code 152 (BAP signal out of range low). 354 (VGT control under duty cycle) and Body Controller – Remote Engine Speed Control #1 – Analog input #2 shorted to ground. Already replace BAP sensor, MAP sensor and VGT turbo.
Why does my international 4300 engine not start?
Replaced injector, put new orings on hipop. It will not start. Runs on ether but dies as soon as ether stops. Replaced both batteries. Checked fuses by batteries. All good. We pulled the ipr and bench tested it. It was working. Scanner says 8 engine codes. They are: FMI=4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE.
What’s the oil pressure on a 2006 International 4300?
SPN175 ENGINE OIL TEMP. SPN 102 BOOST PRESSURE. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 100 ENGINE OIL PRESSURE. FMI= 3 VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE. SPN105 INTAKE MANIFOLD TEMP. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 94 FUEL DELIVERY PRESSURE.
What is the active code of 368 FMI 7?
Active code of 368 FMI 7, EGR driver mod./ECM2 comm. fault. The engine starts and runs, no power. What is the diag. procedure for this? Where is the EGR module located? Submitted: 7 years ago. Category: Medium and Heavy Trucks Andy : Hi there ! My name is XXXXX XXXXX I would like to try and help if I can ! 6H159844. New info.
What is the active code of a 2005 FMI 7?
I Have a 2005 international 4300. Active code of 368 FMI 7, EGR driver mod./ECM2 comm. fault. The engine starts and We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
What does no crank mean on a truck?
The engine turns these lights on. No warning lights means the ECM is not turning on at key on. The crank circuit also goes through the ECM. The ECM will allow the engine to crank if it is booted properly. servicemanager, sickntwisted and Smellfunny Thank this.
Where is the 9260 connector on a truck?
Disconnect chassis connector 9260 Connector 9260 is a 2-wire connector usually located in the battery box. Pin A is the ground connection for the ECM and IDM. See truck Chassis Electrical Circuit Diagram Manualfor complete chassis side ECM and IDM ground circuit information. .)