How to check Detroit Diesel Series 60 ECM?
Detroit series 60 ECM – Answered by a verified Technician. Here is diagram of the vehicle harness plug and the pin outs. graphic. Here is a I am going to attach a diagram of the engine harness also, so you can check the SRS and TRS wires. Series 40 detroit Diesel engine in a motor home. Ddec Iv Ecm Wiring Diagram. Source.
How to troubleshoot a Detroit Diesel engine code?
If any code (s) other than code 25 is logged, refer to the Detroit Diesel Single ECM Troubleshooting Manual (6SE497). Always start and operate an engine in a well ventilated area. If operating an engine in an enclosed area, vent the exhaust to the outside. Do not modify or tamper with the exhaust system or emission control system.
What is wiring diagram for Detroit Diesel engine?
The wiring diagrams cover both the Series 60 engine harness and Series 60 vehicle interface harness. Back to Detroit Diesel Engine Information. DDEC I, DDEC II, and DDEC III & IV Schematics.
Where is the serial number on a Detroit Diesel?
1 ENGINE MODEL AND SERIAL NUMBER DESIGNATION The engine serial number and model number are stamped on the cylinder block in the following location (as viewed from the flywheel end): Left side just below the intake manifold and above the cast-in Detroit Diesel logo. Location of Engine Serial and Model Numbers 2 DDEC II
How to do an EGR test on a Detroit Diesel?
If the PWM voltage measurement is incorrect and the wiring checks were correct, try a test ECU programmed for EGR or contact the Detroit Diesel Customer Support Center at 313-592-5800. Verify repairs. Perform an Active Codes Test “10.4.3.6 Active Codes Test” .
How to check Series 60 EGR section 10.4?
If the supply pressure is between 703-1296 kPa (90-120 psi), perform a VPOD Part Number and Supply Voltage Test “10.4.3.4 VPOD Part Number and Supply Voltage Test and Part Number Check” . Verify repairs. Perform the follow steps to verify the VPOD part number and supply voltage.
How do you replace an ECM in a GM car?
Install hardware on the replacement unit. Reconnect the electrical connectors, making sure they are clean and firmly seated. Install replacement ECM using the hardware from the original unit. 5. TESTING Connect a scan tool to the diagnostic connector located under the dash on the driver’s side.
How does the ECM work on a diesel engine?
The system also monitors several engine functions using various sensors that send electrical signals to the main Electronic Control Module .
Where is the prom chip on the ECM?
PROM access cover is a small metal plate on the ECM used to gain access to the. The PROM is a computer chip located under the access cover in a plastic “PROM.
How do you measure voltage on Detroit Diesel?
Attach a long jumper lead from the battery negative post to the negative lead of the voltmeter. Connect the positive lead of the voltmeter to the three locations listed below, measuring voltage at each point, one at a time while the starter is cranking.
What does high fuel pressure test mean on Detroit Diesel?
If pressure is above 490 kPa (71 psi) with the engine running, refer to “4.14.4.3 High Fuel Pressure Test” , “High Fuel Pressure Test.” If pressure is between 420–490 kPa (61 -71 psi) with the engine running, refer to “12.11 Incorrect Camshaft Timing” 12.11, “Incorrect Camshaft Timing.”
What is the name of the series 60 ECM wiring diagram?
Name: detroit series 60 ecm wiring diagram – Famous Detroit Diesel Wiring Diagrams s Electrical Diagram Name: detroit series 60 ecm wiring diagram – Detroit Series 60 Ecm Wiring Diagram Elegant Fantastic Cummins Ecm Wiring Diagram Contemporary Electrical
Are there any problems with the Detroit Series 60?
This issue did not affect all pre-2002 Series 60 engines, but it was a problem that occurred and could cause catastrophic engine failure. As with most engines, it’s a good idea to keep an eye on your cooling system. Overheating is the cause of many major issues with diesel engines, so maintaining this system can help with many preventable issues.
Are there any Detroit Series 60 engines for sale?
(GOOD USED) 2004 Detroit Series 60 12.7L Diesel Engine For Sale, DDEC 5, 455HP @ 1800RPM, EGR Model, Engine Family# 4DDXH12.7EGY, Serial# 06R0763449, Stock# 1992 Engine is Test Run & Inspected See More Details Detroit Series 60 DDEC 4 435 HP engine checked out and new rod and main bearings installed.
What kind of engine is a Detroit Diesel?
The Detroit Diesel Series 60 is an inline-six 4 stroke diesel engine that was first produced in It deviated from most on-highway engines by being an overhead camshaft engine and having full ” drive by wire ” electronic control. The Series 60 engine can be configured with or without a mechanical tachometer drive.
What causes a Detroit Diesel Series 60 to overheat?
This can indicate a coolant leak. If there is such a leak, you might also notice lower coolant levels in your engine, but things otherwise appear normal. This can lead to an overheated engine. Operators often find that they experience issues with their EGR system on their 14L Series 60 in particular.
What do the signs mean in a wiring diagram?
Wiring diagrams are made up of 2 things: signs that stand for the parts in the circuit, as well as lines that stand for the links between them. Name: detroit series 60 ecm wiring diagram – Detroit Series 60 Ecm Wiring Diagram Elegant Fantastic Cummins Ecm Wiring Diagram Contemporary Electrical
What is the EPROM mount on a DDEC 2 ECM?
The replaceable PROM is an EPROM in the DDEC II ECM. The ECM has isolator mounts for both vibration and electrical isolation. Depending upon application, some units have fuel cooling of the ECM. The engine-mounted system simplifies vehicle wiring for greater reliability. .
What’s the wiring diagram for a DDEC 3 ECM?
DDEC III/IV SINGLE ECM TROUBLESHOOTING GUIDE The following wire schematics support the communication harness; see Figure Figure HARDWARE AND WIRING MULTI-ECMS Engines with more than eight cylinders operate with multiple ECMs. One ECM is called the master, while the others are referred to as receivers.
Where can I buy a Freightliner ECM module?
(Used) 2011 Freightliner Cascadia 125, CPC MODULE- Part Number: A00-24467-902, For more information about this item, give us a call. We ship Worldwide! (CRG HEAVY TRUCK PARTS) 929 W PULASKI… (Used) 2014 Freightliner Cascadia 125, CPC MODULE- Part Number: A00-34461-002, For more information about this item, give us a call.
What kind of electronic control did Detroit use?
Electronic Control. The most popular on-highway Detroit Diesel engine was the 12.7-liter, and the on highway engines were electronically controlled by the proprietary Detroit Diesel Electronic Control (DDEC) system. The DDEC system was the first commercial use of a fully electronically controlled on highway engine,…
When did Detroit stop making the series 60 engine?
The 12.7L engine was favored in buses for its better fuel consumption. In 2007 the 12.7-liter Detroit Diesel Series 60 was discontinued. Once the 12.7-liter Series 60 was discontinued, the 14-liter Series 60 replaced it. By 2008, Detroit Diesel had produced one million Series 60 engines.
Where are the ECM fuses on a 97 379?
They might not be right at the battery connection, but they shouldn’t be too far away from it. Start with where the wires are connected to the positive battery terminal and follow them. You will find them, they are there. They not near batteries in a 97 379.
What is the wiring diagram for a DDEC 3?
One ECM is called the master, while the others are referred to as receivers. The Detroit Diesel Series 60 DDEC III, IV, V, VI Wiring Diagrams are also known as Electrical Schematics or Circuit Diagrams. The wiring diagrams cover both the Series 60 engine harness and Series 60 vehicle interface harness.
What does the DDEC 1 EcM do for the engine?
DDEC I controls the timing and amount of fuel injected into each cylinder. The system also monitors several engine functions using various sensors that send electrical signals to the main Electronic Control Module (ECM). The replaceable PROM is an EPROM in the DDEC II ECM.
Are there any Detroit Diesel Series 60 engines?
This in-line, 4-cycle, 6-cylinder diesel engine uses the innovative DDEC electronic fuel control system to provide engine management reports, answering the high demand for a fuel-efficient heavy-duty engine. The Detroit Diesel Series 60 is offered in three versions: 11.1L (discontinued in 1998), 12.7L (discontinued in 2007), and 14.0L.
What is the model number of a Detroit Diesel engine?
Detroit Diesel Series 60 engines equipped with DDEC II electronic control systems are identified by a “U” in the sixth position of the model number. Example: 6067GU60. Detroit Diesel Electronic Controlled Series 60 engines can be equipped with a variety of options designed to warn the operator of an engine malfunction.
Where are the diagnostic codes on a Detroit Diesel?
Press and hold the switch. Active codes will be flashed on the “Stop Engine” light (SEL) followed by the inactive codes being flashed on the “Check Engine” Light (CEL). The cycle will repeat until the operator releases the diagnostic request switch. DDEC III/IV Diagnostic Codes
When to close EGR on Detroit Diesel truck?
On theory there should be a difference, but let see on practice. Because even the Detroit Diesel Manual says: “….when the truck is over 6500 feet, the computer closes the EGR and the motor starts running like pre-emission engine…..”
Is the Detroit Series 60 14.0 engine for sale?
(GOOD USED) 2008 Detroit Series 60 14.0L Diesel Engine For Sale, 515HP @ 1800RPM, DDEC 6, Engine Family 8DDXH14.0ELD, Emissions: EGR, DPF Model, Engine Serial# 06R1007716, Stock# 1959 Engine is… See More Details
Why does my ECM keep blowing out on my truck?
Driver went in pick up the truck it was running fine, after he was hooked to the trailer, truck stalled again, they took him back in the shop and came back telling me that ECM is blown because of corroded wire. my question is, why would truck start at and runs fine for the first time when he just fixed it with fuses and partial power wire to ECM.
What happens when an ECM loses ignition power?
If it losing ignition (or key) power the key on/off counter will increase. It helps to further diagnose power problems. Most ECMs have more than one power wire.
How tall is a DDEC Series 60 fuel injector?
FUEL INJECTOR HEIGHTS Models: 6067TKXX, 606XPKXX, 606XGKXX (1997-98 DDEC IV and later 1997 DDEC III) FUEL INJECTOR HEIGHTS Models: 6067EKXX, 606XBKXX, 606XMKXX, 606XLKXX, 606XHKXX, 606XFKXX (1998 & 1999 DDEC IV)
What is the right side view of a DDEC IV engine?
Pre-2004 Right Side View 1. EGR Gas Delivery Pipe 4. Intake Manifold Air Temperature Sensor 2. EGR Mixer 5. Barometric Pressure Sensor 3. Intake Manifold 6. Turbo Boost Pressure Sensor Figure 3. Pre-2004 Left Side View An enhancement program has been launched to upgrade production 2004 DDEC IV EGR engines.
What kind of diesel does a Kenworth W900 have?
The truck is a 1999 Kenworth W900 that has been repowered with a DDEC III Series 60. Neither the dealer nor the local Detroit Diesel shop could figure this one out, and after plenty of parts (and money) were thrown at this truck, nothing was solved.
What kind of engine does a Detroit 60 series have?
This engine comes in 2 configurations: factory reman or in-house reman. The factory reman is remanufactured by Detroit Diesel with all genuine Detroit parts.