What are the fault codes for Cummins ISL9?
Intake Manifold 1 Pressure – Data Valid But Below Normal Operating Range – Moderately Severe Level Intake Manifold 1 Pressure – Data Valid But Below Normal Operating Range – Moderately Severe Level Accelerator Pedal or Lever Position Sensor 1 Circuit – Voltage Above Normal or Shorted to High Source
Why do I get codes 3382 and 2554?
Replaced EGR valve, pressure sensor, cooler, removed DPF cleaned out. it was packed full of soot. Along with the whole EGR system. I am still getting codes 3382 and 2554. Truck is smoking brown-ish smoke. truck bogs like crazy until codes kick in and EGR is disable then will run great with check engine light on?
What’s the fault code for a 2011 Pete?
Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by habfleet, Dec 18, 2016 . I have a 2011 Pete with a PX-8 engine (ser#73301527). Had the above code.
Is the CM2350 the same as the ISL9?
This engine was also commonly called the “ISL” until 2016, when it was renamed the “L9” or “ISL9”. The CM2350 is the accumulation of all emission related technology from 2007 to current, including EGR valve, EGR cooler, DPF filter, DOC, and SCR. There 558 codes for this series engine, and our website has detailed troubleshooting on all of them.
What is the ISC Code for a Cummins ECM?
Here are all the ISL and ISC fault codes available for the Cummins ECM. These Cummins trouble codes pertain to both models equipped with the CAPS fuel system. ISC Fault Codes # 111-500 111 Electronic Control Module (ECM Microprocessor
What is Technical Service Bulletin for Cummins L9?
Cummins ISC, Cummins ISL9, Cummins L9. Electrical system. This technical service bulletin describes the verification and resolution of engine wiring harness issues on j1939 datalink that are causing datalink related fault codes 1894, 2771, 3232, 3868, 3911, 4151, 4152, 4572, 4677, or 6688.
What are the trouble codes on a Cummins?
These Cummins trouble codes pertain to both models equipped with the High Pressure Common Rail (HPCR) fuel system. 0002 Exhaust Gas Pressure Sensor Number 1 Circuit – Voltage Below Normal, or Shorted to Low Source 0003 Exhaust Gas Pressure Sensor Number 1 Circuit – Data Erratic, Intermittent, or Incorrect
What happens when there is a trouble code on a Cummins Engine?
If there are active trouble codes recorded, flashing lights immediately appear. The numbers of the fault codes flash in the following sequence: the warning signal (yellow) flashes first, highlighting the digit of the fault code. There is a short, 1- or 2-second pause, then the “Stop” signal (red) starts flashing.
How does the warning light work on a Cummins Engine?
The numbers of the fault codes flash in the following sequence: the warning signal (yellow) flashes first, highlighting the digit of the fault code. There is a short, 1- or 2-second pause, then the “Stop” signal (red) starts flashing. After a new pause, the warning light returns again.
What are the ISC codes for Cummins ECM?
449b Injector Metering Rail Number 1 Pressure – Data Valid But Above Normal Operating Range – Most Severe Level 449cl Injector Metering Rail Number 1 Pressure – Data Valid But Above Normal Operating Range – Most Severe Level 451 Injector Metering Rail Number 1 Pressure Sensor Circuit – Voltage Above Normal or Shorted to High Source
What is the ISC Code for Cummins injector rail?
268 Injector Metering Rail 1 Pressure – Data Erratic, Intermittent, or Incorrect 269 Antitheft Password Valid Indicator – Data Erratic, Intermittent, or Incorrect
What do the ISL and ISC codes mean?
These ISL & ISC codes are for quick reference to find out what your fault means. ISL & ISC codes can help pinpoint the problem and save hours of frustration. For Cummins ISL & ISC codes on earlier models (2002 and before) use ISC and ISL codes, CAPS fuel system.
Are there any cookies on my ISL9 Cummins?
By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. I have a ISL9 cummins with 5 codes 1 is 3232 active amber… good morning I have a…
When does a Cummins fault code go inactive?
3712 – Aftertreatment SCR Operator Inducement- Data Valid but Above Normal Operational Range- Most Severe Level Conditions for Clearing the Fault Code This fault code will go inactive once all other active fault codes have been addressed. Refer to the appropriate fault code troubleshooting tree.