What is the code for 2007 International 4300 DT466?
2007 international 4300 DT466.A/C code 613-14a what does it mean ? Clicking this will make more experts see the question and we will remind you when it gets answered.
Are there two stored codes for 2023 14P?
I’m tossing 2023 14p it says there are 2 stored codes. It’s the same number twice proceeded by a 150 1 and 150 2 followed by 2023_14p I’m really looking for a full dtc list.
How do you find the engine code on an IH 4300?
You then count and record the flashes of the Amber engine light. They are 3 digit codes. The code list is in the stickies I believe. A bit of a PItA but it works. To clear codes you hold the buttons, turn key on and pump throttle 3 times.
How do you clear a code on a 4300?
To clear codes you hold the buttons, turn key on and pump throttle 3 times. Well I tried it on the truck im driving. (2002 4300 dt466e) No flashes.
Are there any 2007 International 4300 trucks for sale?
Our company has three impact attenuator trucks for sale. All three are the same year, make, model and have similar amount of miles (268,000). These ar… 2007 INTERNATIONAL 4300, DT466, 210 HORSE POWER, FULLER 6 SPEED, 10,000# FRONT, 21,000# REAR, 2018 UNITED 2300 GALLON WATER TANK, 2 FRONT, 2 SIDE, 2 R…
How big is a 2007 International dump truck?
2007 International, 4300, Truck, DT466 20 FOOT STAKE BODY, , 2007 INTERNATIONAL 4300 WITH THE POWERFUL PRE- EMISSIONS DT466 255 HP ALLISON 3000 TRANSM… 2007 INTERNATIONAL 4300, 2007 International 4300 SERIES 13 FOOT DUMP TRUCK DT466, NON CDL NO SPECIAL LICENSE REQUIRED TO DRIVE, Dump Truck, WE ARE PRO…
Why does my international 4300 check a / C light?
Turns out it was the motor that switches the flaps in the dash from defrost to floor and vent now why that shuts the compressor down i have no idea but a $34.00 motor did the trick.
How to reset the a / C on a 2007 DT466?
Using the cruise control buttons, at the same time push the left button up and the right one down to pull the codes on the dash. To RESET all codes and start the A/C again push both cruise control buttons UP.
Where is the resettable breaker on a 2007 DT466?
No the check AC light was not on. Just tried it and it worked!!! all codes were reset and well still no ac tho . The fuse that is under the dash inside the cab is good the resettable breaker type with the little color tab on top. I dunno where else to check if there is another panel besides the other one under the hood on the drivers side.
What does the a / C code 1 : 3 613-14a mean?
By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. I need to know what the a/c code 1:3 613-14A means on a 2007…
What are the fault codes on an international 4300?
I have a 2007 International 4300 with several fault codes on the check A/C illuminated. The VIN is 1HTMMAAM67H379002. Here are the fault codes: 1:4 613_14A 4:2 2033_14A 33:239 639_14P 1:5 613_14P 1:1 … read more
What are the codes for the dt4300 7.6L?
I have a 2006 International DT4300 7.6l with EGR , I have codes 168-04 VGT Actuator , 1-05 through 6-05 injector circuits , 223-04 Control # XXXXX , 254-06 control # XXXXX , 2 … read more
What’s the trouble code for a 1995 dt466e?
That is good for 1995-1999 DT466E engines. Good Day! I’ll sticky this for you guys…. I can also post the newer engine DTC lists if you would like. If you could post the trouble codes for the later DT466E i would appreciate it. I have ordered the Intl. CD Manual but would like to start on the codes in my 2002 truck.
What’s the code for a DT 466E diesel truck?
We got couple of 05 International truck that has VGT problem. Code 152 (BAP signal out of range low). 354 (VGT control under duty cycle) and Body Controller – Remote Engine Speed Control #1 – Analog input #2 shorted to ground. Already replace BAP sensor, MAP sensor and VGT turbo.
When did the Navistar service manual come out?
S082853 Copyright©09/15/2003 International Truck and Engine Corporation S082853 09/15/2003 3200, 4200, 4300, 4400, 7300, 7400, 7500, 7600, 8500, 8600 SERIES Built After September 15, 2003 — ELECTRICAL CIRCUIT DIAGRAMS
What do SPN and FMI numbers stand for?
The tech will need the SPN and FMI numbers and might ask for the SA number as well. Diagnostic trouble codes (DTC) will end with an “A” while the code is active. The code will remain active as long as the feature affected is active and the fault is present.
How to fix FMI 14.1.5 SPN 613?
Turn the key switch to the ACCESSORY position to view only previously active codes. Turn the key switch to the IGNITION position to view both active and previously active codes. Momentarily press the Cruise ON switch and the Cruise RESUME switch at the same time.