Why does my international 4300 DT466 not start?
If theres any air in it at all, it wont start. . The daytime running lights (DRL) and low beam headlights are inoperable. The highbeam headlights, markers and all other lights function properly. I have checked the fusebox in the engine compartment and above the glovebox and am unable to locate either a DRL/headlight, fuse or relay.
Why does my 2004 DT466 engine not start?
I have a 2004 4300 international dt466 it cranks but no start. I have changed all sensors still nothing check fuel pressure injector orings im stuck. Engine position sensor shows up when u put computer on it. Where should I check for a broken wire maybe? Plug to sensor has power and sensor is good.
Can a 2007 IH 4300 run in sub zero temps?
The place I work at has a 2007 IH 4300 with a DT466. The past few days have been sub zero temps here. It ran fine the beginning of the week but yesterday it wouldn’t start. We pushed it in the garage and let in warm up over night. We also put the batteries on charge since they were pretty weak.
Where is the crank position sensor on a DT466?
If not replace the crank position sensor located on the bell housing on the driver s side . Pull the from fender off and you will see it . It is a two wire sensor with a square connector . Is it above the starter?
Why does my dt466e no start-fuel problem?
Got that all fixed. Realized that my primer pump would leak when I would pump it, replaced the entire assembly. Filled both filters, truck fired on the first try. Now today go to run a call, cranks and cranks wont start. Gave a shot of ether, fires but wont run on diesel.
What should fuel psi be on dt466e International diesel?
Usually when we get no start cold but fires and runs after using ether it might be injectors, but you need to do the fuel checks I posted and let me know. If you don’t have a fuel psi gauge, autozone loans them out. I like to have around 60psi I have seen them run ok above 45psi.
Why does my dt466e take so long to start?
The high psi oil system, in a dt466e you have high psi oil that fires the injectors, and sometimes the pump can actually bleed down overnight causing it to take forever to start, the only way to check that will be let it sit overnight and there is a temp sensor in the front cover/ drivers side . it is right in front of the oil/fuel pump.
What are the trouble codes for International trucks?
International Trucks Diagnostics Trouble Codes (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar
Why is my International 4700 engine not starting?
I am dealing with an international 4700 w/ the dt466e engine option and am unfamiliar with the fuel and engine control system. The drain plug on the high pressure oil pump was stripped and was run dry, truck was then shut off, and would not restart several hours later after being refilled.
Why does my dt466e diesel engine not start?
DT466E international diesel wont start… Will it stay running, after you ether it? Or does it just die out again? Do you have access to a scanner, any engine light on? Does the tach read while you are cranking? Can you use the hand primer on the filter base to try and prime system, if it does not get hard to pump you are most likely sucking air.
What’s the trouble code for a 1995 dt466e?
That is good for 1995-1999 DT466E engines. Good Day! I’ll sticky this for you guys…. I can also post the newer engine DTC lists if you would like. If you could post the trouble codes for the later DT466E i would appreciate it. I have ordered the Intl. CD Manual but would like to start on the codes in my 2002 truck.
When did DT466 truck die and will not start?
(1) August 2015 truck was towed back to our place. One of the guys here said that he drained water out of the fuel and the truck started, but then it didn’t start next day so we called local mechanic and he checked electrical connectors and found that fuse in battery box was not making connection and shorted.
Where is the fuel pump on a DT-466?
JaymZH2 wrote: fuel pump would be my guess. not sure on the older ones, but the newer DT’s it is on the drivers side mid block towards the front. a couple bolts a 2 lines and your done. I have a 2000 4700 DT-466, would what you call the fuel pump be the same thing they call the “high pressure pump” in the book that the lines from the filter go to??
What to do if your International Truck won’t start?
International 4700 Truck Won’t Start, Ignition Switch or Gear Selector ? (Solved) – YouTube International 4700 Truck Won’t Start, Ignition Switch or Gear Selector ? (Solved) If playback doesn’t begin shortly, try restarting your device.
What can I do if my gear shift is stuck in reverse?
Gear shift is stuck in reverse, car wont start, the knob to move shifter will not depress. All the lights come on in the car, the gear shift is stuck in the reverse position. What can I do to try and fix it?
Why does Autoshift not go into any gears?
When i have the truck off and turn key to start position and try to shift gears i can hear the transmission shifting successfully, however once the engine is running it will not shift gears. There are no service lights or error codes being displayed.
What should the fuel pressure be on an international 4300?
Need 20 psi to start, 65 psi when running. Hold your schrader valve open during crank to make sure there is solid fuel flow there. If you have the test fitting on the fuel filter cap, you can check for pressure there too. Even the hand primer pump should be able to build up to 60 psi and get hard. spsauerland Thanks this.
Why is my DT 466 getting hard to start?
The 466 uses oil to hydraulicly actuate your injectors. Once the o-rings start to leak, the high pressure pump has a hard time building pressure to actuate the injectors. Sometimes it takes 30 seconds to finally build enough pressure to start. This is about a 2 hour job at a dealer. Did you check ALL fluids accurately?
Can a 2007 International 4400 cab start fine?
No announcement yet. I have a 2007 International 4400 commercial cab KME. I love the engine. However, it has a starting issue. Sometimes it will start fine, but and jump the two large terminals on the starter solenoid on the starter. you don’t need to hold the screwdriver across the contacts till it starts. Once it starts it is fine.
Why does my 466 pump have a hard time starting?
You probably have a leak on your high pressure oil rail. More than likely, needs a new o-ring set. The 466 uses oil to hydraulicly actuate your injectors. Once the o-rings start to leak, the high pressure pump has a hard time building pressure to actuate the injectors. Sometimes it takes 30 seconds to finally build enough pressure to start.
How to reset the HVAC on an international 4300?
Click to expand… The right way is to remove the HVAC Control B+ fuse to accomplish a reset, just as mrdevildog suggests, there is then no risk of damage to the controller or dash panels.
Where are the lights on my international 4300?
The highbeam headlights, markers and all other lights function properly. I have checked the fusebox in the engine compartment and above the glovebox and am unable to locate either a DRL/headlight, fuse or relay. We would love to have a troubleshooting guide, or schematic, but have been unable to locate one on the internet.
What makes a 2003 International 4300 sputter and Miss?
I have a 2003 International 4300 with a DT466. I just had all the O-rings on the injectors replaced along with the wiring harness that goes to the injectors. Now once the truck gets up to running temp it starts to sputter/miss. Truck runs GREAT cold but once warm gets worse.
What are the engine codes for an international 4300?
Scanner says 8 engine codes. They are: FMI=4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. FMI=3 VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE. SPN175 ENGINE OIL TEMP. SPN 102 BOOST PRESSURE.
What’s the oil pressure on a 2006 International 4300?
SPN175 ENGINE OIL TEMP. SPN 102 BOOST PRESSURE. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 100 ENGINE OIL PRESSURE. FMI= 3 VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE. SPN105 INTAKE MANIFOLD TEMP. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 94 FUEL DELIVERY PRESSURE.
What is the Mil code for a 6.7L diesel engine?
Aug 25 2014 5299-2011-2015 F-Super Duty – 6.7L Diesel – Runs Rough or Cranks no Start With MIL On And Diagnostic Trouble Codes (DTC) P0087, P0088, P0089, P0093,P228F, P2291
Is the 6.7L Power Stroke engine crank no start?
Some 2011-2015 F-Super Duty 6.7L diesel equipped vehicles may exhibit an illuminated MIL and DTC P0087,P0088,P0089,P0093, P228F or P2291 associated with a rough idle or crank no start condition. If this condition is present, inspect fuse 33 in the Battery Junction Box (BJB) for an open condition.
What is fuel pressure on international 4300 MaxxForce 466?
I have a 2011 International 4300 Maxxforce 466. Just did a PM service, now a hard start when code .need to starting fluid to initially get it running. Code pops up, SPN 931 FMI 11. I check fuel pressure on the computer, 74 psi.
Is the DT466 Turbo good for low power?
The clutch is fine, just got adjusted about a month ago, no smoke, just low power. Air filter is clean. Oil pressure is good. Temp was fine. No lights came on. The turbo isn’t really as noticeable in sound, but I can still hear it.
What causes loss of power on DT466 truck?
Check that all your turbo hoses are connected and not broken. this will cause a loss of boost. They’re all good. Turbo just isn’t noticeable really like it used to be. Truck is just starting to run slow anymore.
What should off hand rpm be on DT466?
If it cranks don’t rev it unless you have a gauge to handle about 3000psi. Off hand should take close to 600psi to start. also you can pull the valve cover and apply shop air pressure into the rail and look for air bypassing the injectors.
Why does my DT 466 e no start?
Fuel filter was filled before starting it almost ran chugged and stalled and will not start. I Worked the hand pump for quite a few cycles and bled the scrader valve, starts to fire and thats it. Q. What am I missing? 2003 International 4300, 330,000, original injectors.
How big is the fuel filter on a DT 466?
It is around 1-1.5 inches in diameter, and is aobut 2 inches long, and will most likely be painted the same color as the engine. It is a plastic spin-on deal, and it is meant to catch any big stuff before going into the fuel filter itself.Bascially, it is like a bowl on a carberator on a briggs and stratton.
What are the International fault codes for Navistar trucks?
Fault Codes DTC of International Navistar Truck 311 EOT Engine Oil Temperature signal out-of-range low 312 EOT Engine Oil Temperature signal out-of-range high 313 EWPS Engine Oil Pressure below warning level
What does p0016 stand for in Powertrain Control Module?
P0016 – Crankshaft Position – Camshaft Position Correlation – Bank 1 Sensor A Description: The powertrain control module (PCM) monitors the variable camshaft timing (VCT) position for a misalignment between the camshaft and crankshaft. The test fails when the misalignment is greater than 1 tooth. Possible Causes:
How to know if a DTC is not available?
Suspect parameter number (SPN), failure mode indicator (FMI) and occurrence count numbers are listed. Source addresses and DTC descriptions are presented in plain text. NOTE – The VID will display “Not Available” if a DTC description is not available for a particular fault.
Why is my DT466 diesel not getting fuel?
Pump shaft seals can leak and let air in pump and fuel in crankcase. Normally that creates a cold start problem after setting a while and a crankcase full of fuel when running. Normally dying while running is a problem between the injection pump and tank.
Where is the lift pump on a DT466?
No, the lift pump is mounted to the HPOP about 1/2 way up the left side of the engine rear face of the gear cover (just above the air compressor, if it has one). Did you find the recommended reading relevant to this discussion?
Is the Check Engine light on on my DT466 MHH?
Only the Maxxforce engines (2007 and newer) communicate on J1939. All pre Maxxforce engines 2006 and older only communicate on the J1708 network. Try Servicemaxx J1708. Does the check engine light come on at all? If not then ECM not powering up. I have saw a few times with the fuse box located out on the driver side above the steer tire give fits.
Why is my international firehouse starter not working?
If not the solenoid probably has a small crack in the coil causing an intermittent fault that can be “shocked “into working by jumping the terminals. Solenoid shouldn’t be too expensive for that starter. Where’s TC when you need him. He’s the king of cornbinders. Where’s TC when you need him. He’s the king of cornbinders.
Is there a check engine light on a DT466?
05 DT466 truck loss power but no code or check engine light! FIXED…. 05 DT466 truck loss power but no code or check engine light! FIXED…. 05 DT466 truck loss power but no code or check engine light! FIXED…. It is normal for there to be codes with no check engine light. You will need to have someone scan the engine for codes.
Why does my DT466 diesel engine not start?
It was blowing Fuse 30 and that Fuse services the Diesel Fuel heater, Waste-gate Solenoid, and the Injector Driver Module Relay coil , PCM relay coil. I’m betting yours is something similar.
Is the DT466 truck loss power no code?
– Tow411 05 DT466 truck loss power but no code or check engine light! FIXED…. 05 DT466 truck loss power but no code or check engine light!
What kind of engine does an international dt466e have?
The truck is an International 2004-2006, Model 4300, Engine DT466E with an Allison MD transmission. The rated HP is 245. 1. DTC: 222, SPN: 247, FMI: 2 Break Switch Circuit Fault; 2. DTC: 353, SPN: 27, FMI: 5 VGT Over Duty Cycle; After I got the DTCs from ServiceMaxx I was able to find some info on the 222 from the ISIS software.
What kind of car is the DT 466?
Can’t seem to figure this one out myself, so I figured I’d try here. 2003 International 4300 with the 466, and have been having some issues. Used to start and run beautiful, probably the best running dt I’ve driven.
Why does my DT466 start warm / hot?
The FACT that it starts good warm/hot MEANS that you DO NOT have a problem with the HPOP, IPR valve or other HEUI mechanical components because if you did, it would not start HOT very well. THEN re-install the good batteries and try it. On the cheap and quick, use a charger to boost voltage during cranking set to 12V Med or LESS.
What to do if your DT466 fires right off?
Try putting a battery charger on it, 12V low or Med at most, if it THEN fires right off, you’ve got a bad connection somewhere in the ECM or IPR circuits- This is VERY common. Thanks for all the input guys, I think I may have an idea what’s happening, correct me if I’m off track.
What are the crank times on a 2005 DT466?
We have 2 of the 2005-2006 DT466s, when cold, long cranking times then an unnerving high speed rev up and black smoke till they settle down are the norm. They are one of the reasons we switched to 5W-40 motor oil, both to make me feel better about the cold high speed rev up and to help with the cold cranking speed.
How long does it take to start a 05 dt466e bus?
I have 11 05 DT466E buses in my fleet. Out of the 11, only 4 like to start. The rest have extended cranking times. sometimes it takes up to 45 seconds of cranking to get them started, and the cold only makes it worse.
How to reset a / C on International trucks?
You can by pass each of the 2 thermistors with a 1500 ohm 1/2 watt resistor at the harness plug. Without Diamond Logic you can not monitor thermistor temp. so this is the way that you can quickly make sure that your thermistors are working. (after you remove battery cables for 5 minutes to reset) It works!
What kind of transmission does a 2002 International 4300 have?
We have a 2002 International 4300 with the automatic trans w/ park. We have been having some really bad transmission problems with it. The truck will run fine for 2 days then all of the sudden the “check trans” light will come on and the truck will not shift out of low gear.
Where is the starter on a 2004 DT466?
If you start from behind the head and start feeling downwards and onto the bell housing you will see that it is mounted with one small bolt at about the 11 o’clock position . It is above the starter by about 12 inches for sure but right on top of the bell housing .
What kind of engine does the Navistar 4400 have?
The 4400 was also produced in a semitractor; sitting 4 inches higher than the chassis truck, the 4400 tractor was the only version offered with the DT570 engine as an option. For 2008, coinciding with the introduction of the International ProStar and International LoneStar, Navistar revised the branding of its truck model lines.
Where can I find a DT466 wiring diagram?
2004 4300 International Truck Wiring Diagrams Diagram Files Sel I Have 4300 2002 Dt466 Turn Key No Power To Starter Batters Good Found If We Put Ground Wire
Why does my 2012 International have no start?
I have a 2012… I have a 2012 international with a maxxforce DT and it has a crank no start. Initially though it was a HP oil issue and replaced the ICP and IPR.
Can a crank no start engine still start?
Still have a crank no start. no codes pulled and on the live data while cranking the highest oil pressure reading was 1700psi and supply fuel was 73 psi. the engine will jump once like it wants to start when the oil pressure is at it highest but goes back to just cranking. Mechanic’s Assistant: How old is your oil pump?
Why is the ECM not working on my DT466 MHH?
If not then ECM not powering up. I have saw a few times with the fuse box located out on the driver side above the steer tire give fits. The fuse holder will get loose and not make good connection. In that fuse box on the fender. Check the IDM relay. There should be battery power on 2 of the terminals. Those are the clean power wires.
How many times has DT466 truck broken down?
The guy at Southland International (where we have it had recently towed twice) said it that neither time were there any active codes, only inactive codes and “one triangle” which he said meant service work would soon be needed. So now it has broken down 4 times with the exact same symptoms.
What kind of engine does an international 4300 have?
2007 INTERNATIONAL 4300 STOCK 1657, ENGINE INTERNATIONAL DT 466 , 7.6L, 230 HP, AUTOMATIC, AIR SUSPENSION, AIR BRAKES, 18FT REEFER BOX WITH CARRIER UN… 2006 International 4300 24′ Van Truck, DT466 7.6L Turbo Diesel Engine With 220HP, 5 Speed Automatic Transmission, Hydraulic Brakes, Spring Suspension,…
How big is a 2007 International 4300 dump truck?
2007 INTERNATIONAL 4300, 2007 International 4300 SERIES 13 FOOT DUMP TRUCK DT466, NON CDL NO SPECIAL LICENSE REQUIRED TO DRIVE, Dump Truck, WE ARE PRO… 2007 International 4300 Utility Truck with Rear Mounted Back Hoe, 11 Ft Service Body, Truck-mounted Bradco Backhoe with 11 Inch Bucket, Hydraulic Outr…
Is the DT466 truck getting hard to start?
I have had a small problem with it before, usually first thing in the AM. But now it doesn’t want to start no matter what time of the day it is. If its been sitting for any length of time it cranks and will finally start after about 45 seconds. There is nothing else wrong with this truck, this is the only problem it is giving me now.
What is the ICP on an international dt466e?
The icp is between 800 and 900 psi while cranking, fuel pressure is I have an international dt466e that will not start. The icp… HeavyEquipmentTech : Hi my name is***** will try to help.
What kind of truck wont crank the key?
Discussion in ‘ International Forum ‘ started by sickntwisted, Sep 10, 2014 . This truck has been haunting me for mths, 2006 international DT466 truck wont crank turn the key nothing all the relays click, the only thing i hear when i turn the key is the turbo?? (someone at international told me that’s what it was) the injectors do NOT pre cycle.
What does no crank mean on a truck?
The engine turns these lights on. No warning lights means the ECM is not turning on at key on. The crank circuit also goes through the ECM. The ECM will allow the engine to crank if it is booted properly. servicemanager, sickntwisted and Smellfunny Thank this.
What are the problems with the Allison 4300 automatic Trans?
When the hood is close, it pull the harness out of the firewall giving it a bad connection at the connector.Had this problem on 3 late model 4300″s. I had this same problem and called the Allison shop and the guy said to wiggle the wiring harness connector on the tranny and firmly push it in.
What to do if your engine won’t start?
Low or no fuel pressure is one thing the engine will not log a code for. Low or no ICP will log a code during crank no start conditions. So if you are not seeing any icp codes, I would focus on the fuel. Need 20 psi to start, 65 psi when running.
Is the dt466e a 2001 International Truck?
The Hi, I have a 2001 international truck with the DT466E. The truck was pulling hard up a hill when the warn/engine light came on and it lost power. It has codes 333 and 335. It starts with a wiff of eit … read more
What is the code for the dt466e engine?
Hi, I have a 2001 international truck with the DT466E. The truck was pulling hard up a hill when the warn/engine light came on and it lost power. It has codes 333 and 335. It starts with a wiff of eit … read more I have a 2008 International 4300 w/ dt466. It has a long cranking I have a 2008 International 4300 w/ dt466.
What kind of engine does 2006 International 4300 have?
2006 International 4300 with a DT466 engine. The engine had low ICP and wouldn’t start a couple weeks ago. I pulled IPR valve, found … read more I have a 2007 International 4300 VIN#*****************. My 2007 International DT 466 keeps shutting off and starts right back up. Someone told me it could be the turbo acuator SID0027 … read more
Is the International 4400 DT466 a reliable engine?
I hope that you will work with me on this matter. International advertises that the DT466 engine is reliable, durable, low downtime, and minimal maintenance. I have not had the opportunity to enjoy any of these advantages.
Is the 2006 DT 466 crank no start?
2006 dt 466 crank no start after fuel filter replacedment. Andy.I have an international 4300 dt466. it starts and stalls… Have a 4300 international w/ dt 466. Stopped running. Codes Have a 4300 international w/ dt 466. Stopped running. Codes are sid: 254 fmi:6 and sid:221 fmi: 4 . Changed the idm.
Why does my Ford truck not start when its hot?
I have an 89 f 250 mine wont restart when hot. I can move the distributer and it will start again. So weird. When its hot it sounds like the battery is dead and wont turn over till I retard the timing. 83 people found this helpful.
Are there any problems with a 2006 International 4300?
Andy.I have an international 4300 dt466. it starts and stalls… Have a 4300 international w/ dt 466. Stopped running. Codes Have a 4300 international w/ dt 466. Stopped running. Codes are sid: 254 fmi:6 and sid:221 fmi: 4 . Changed the idm. It ran 1/2 a day.Originally I could disconnect the batts. and connect cabels to kil … read more
Is the DT466 over heating still a problem?
We have a 2001 International 4700 with the Dt466. The cooling sytem has been gone through but it is still having overheating problems. Does anybody know of any fixes or a better radiator design than this 1/2 of a radiator crap.