How to reset ignition PassLock on a 2003 Saturn Ion 3?

If the Passlock system does not automatically reset, it can be reset manually. Turn the ignition key to the “Start” position as if you are starting the engine. Turn the ignition key to the “Run” position after two to three seconds. Leave the key in this position for 10 minutes.

How does the security system work on a Saturn Ion?

The Ion uses a passive alarm system that arm when you exit the vehicle and lock the doors with the keyless remote. If at any time the doors are opened without the use of the remote or the keys the alarm will sound. This is to prevent the theft of contents within the car.

How do you turn off the engine on a Saturn Ion?

Turn the key to the off position without removing it and back to “Run” for 10 more minutes. Turn the key off again and back to “Run” for 10 minutes a third. Turn the key off and then attempt to start the engine.

When does the anti theft system car wont start?

If the engine does not respond or dies immediately after cranking up, leave the key in that position for 10 minutes. When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

How to solve the anti theft system car wont start?

It is another way to solve the problem of anti theft system car wont start. Disconnect the positive terminal of the battery for a minute or two. Reconnect it and make sure that both the anode and cathode terminals are tightly attached. It will reset the computer system and your car is likely to kick off.

What does the PassLock system on a Saturn do?

The Passlock system is intended to prevent a worn (worn keys use to be about to start any of the earlier model Saturns without any security system) or incorrect key from starting the car. If the proper code is not sent then the BCM will shut down the car for up to 10 minutes.

Where is the ignition switch on a Saturn?

The problem was due to the original ignition switch which is a $50 part from Saturn. The ignition switch is located on the back end of the ignition lock. The ignition switch sends a code that is generated in the ignition lock to the body control module (BCM). It is a part of the Passlock2 system on the 2004 Saturn.

What are the problems with my 2004 ion2?

Need some confirmation. Having intermittent starting problems with my 2004 ION2. Insert key, turn on, lights come on but no turnover. Sit a few minutes, turn on, tries to start but dies as if no gas, or get a turnover and that’s it. Sit another couple of minutes, turn on, lights, no turnover.

What should I do if my Saturn ignition is not working?

Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.

How does the ignition switch work on a Saturn?

Saturn vehicles use a transponder inside the ignition key to prevent unauthorized engine starting. There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start.

Can a faulty ignition switch cause a car to not start?

There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start. If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced.

How does the PASSKey System on a Saturn Ion work?

The PASSKEY system uses an exciter coil located inside the key lock tumbler that detects the correct key being inserted and turned to start the car. When the correct key is turned in the cylinder it sends a signal to the computer which will then allow the fuel injectors to function.

Is there an anti theft system on a Saturn Ion?

But most of today’s vehicles come equipped with an anti-theft system that is integrated into the vehicle’s computers. The 2007 Saturn Ion is one of them. The Ion uses two systems that provide different functions, but for the same purpose: to prevent theft.

How to program a new Saturn key without the original?

Saturn key cutting – Who can cut a new key, what is the procedure, cost and more Saturn key fob battery – Cost, how to replace, type, size, programming, what do to when the battery is dead and more. How to program a new Saturn key without the original?

What kind of key fob does Saturn have?

Saturn is among the variety of vehicles manufactured around the world that features the popular keyless entry system technology.

Do you need a new ignition key for a Saturn Aura?

Furthermore, remember to ask if the key needs to be programmed or coded, some models do – e.g., a replacement key for 2008 Saturn Aura will need to be programmed, whereas a 1996 Saturn SC won’t. If you think you need a new ignition switch/ lock cylinder, first make sure you don’t simply need a new key.

Saturn is among the variety of vehicles manufactured around the world that features the popular keyless entry system technology.

What happens when I turn the key on the starting circuit?

Now, thinking about that starting circuit, consider the things that could be going wrong to interfere with it.

Why does nothing happen when I turn the key?

Think of this process as a water pipe with a series of loops that get smaller and smaller in diameter, increasing the water pressure without increasing the amount of water flowing through. This makes the water jet out the other side faster and further than it would have at its original pressure. Like a https://youngchoppers.com list of hitches.

What happens when you turn the ignition key on a Saturn?

If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.

Where is the fuse on a Saturn ignition?

Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover. Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover. Remove the fuse using a fuse puller in the fuse box.

What happens when ignition PassLock is not reset?

The system disables the ignition if it detects that starting the car is attempted with an invalid key. When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets. If the Passlock system does not automatically reset, it can be reset manually.

Who is the owner of the Saturn Ion?

SATURN, the SATURN Emblem, and the name ION are registered trademarks of Saturn Corporation. GENERAL MOTORS and GM are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.

Is the Saturn Ion a trademark of General Motors?

Where can I get a replacement Saturn key?

If you are looking for a Saturn key fob or Saturn car key, look no further. We have almost every Saturn replacement key fob and replacement Saturn key in stock and ready to ship.

Where is the data port on a Saturn?

Insert your key into the ignition and leave the key in the “Off” position. Locate the car’s data port on beneath the dash board panel on the driver’s side. Notice the eight data terminals on each side of the port and connect the jumper wire to the 8 and 4 terminals, which are eighth and fourth from the left side of the port on the top side.

What happens if the clutch safety switch fails?

The clutch safety switch is designed to close and provide electricity when the pedal is depressed. However, if the switch fails, it will not be able to provide power for the starting circuit. This will lead to a vehicle that does not start when the key is turned, even if the pedal is depressed. 2. Starts while in gear

How do you reset passkey on Saturn Ion?

Resetting the PASSKEY can be necessary at times if the programming in the module becomes corrupted or if a new key and key cylinder are installed. To reset the system, get in the car and shut the door. Turn the key on to the “Run” position without cranking the engine. Leave the key there for exactly 10 minutes.

Why is my ignition not working on my Saturn?

If there is a “click” when you try to crank the engine but the engine won’t start, the problem may be with the ignition key transponder. You will need to have both of these components serviced by a Saturn dealership. For specific information about your Saturn’s ignition system, consult the particular vehicle’s manual (see Resources).

What should the circuit resistance be on a Saturn Ion?

There’s an open in the circuit resistance is above 200 ohms and a loose terminal or a faulty module if below 200 ohms. Measure the resistance between the crankshaft position sensor’s terminals A and B. (Disengage the DIS module’s five-pin connector first). The resistance should be 700 to 900 ohms.

What to do if your ignition system is not working?

Most causes of ignition system problems can’t be corrected by a non-expert, but there are a few things you can do to discover a problem’s location. It primarily involves checking for sparks on the spark plugs and ignition coils. Remove a park plug wire from the plug and connect it to a spark tester.

Is the starter interrupt warning light on or off?

Depending on the current status of the system, the warning light will be off, on steady, or flashing. Although they may share the same dash-mounted warning light, these “starter interrupt” anti-theft systems work separately from and independently of the “content theft” systems available from factory and aftermarket suppliers.

Is it normal for the security light to go off when the engine is running?

After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal. Depending on the system, replacement of key components will necessitate that a relearn procedure be completed.

Navigation