What is the engine code for a 2003 Saab 9-3?
As far as symptoms associated with this code P0340, i am having a loss in power and what seems like a rapid misfire. Currently P0340 is the only engine code I have. Any and all help with this issue would be much appreciated. You do get codes for these, but you don’t have a cam position or separate knock sensor on this engine.
What does the camshaft position sensor on a Saab do?
P0340 Saab Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
What causes the p0340 code on a Saab 9-3?
Saab 9-3 P0340 Causes As stated above, the P0340 code is often caused by a failure in the Camshaft Position Sensor itself. Here are the most common causes: Wiring Issue– The Camshaft Position Sensor wiring is exposed to harsher conditions than a lot of the wiring in your 9-3.
Where is the ion module on a Saab 9-3?
The ION module is on end of engine, upper right rear near brake and coolant reservoir, rectangular plug wire bundle leads to coil packs.
As far as symptoms associated with this code P0340, i am having a loss in power and what seems like a rapid misfire. Currently P0340 is the only engine code I have. Any and all help with this issue would be much appreciated. You do get codes for these, but you don’t have a cam position or separate knock sensor on this engine.
P0340 Saab Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
What does the p0340 code on a Saab mean?
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals. Need more information on how to fix the P0340 SAAB code?
The ION module is on end of engine, upper right rear near brake and coolant reservoir, rectangular plug wire bundle leads to coil packs.
What does code p0340 mean on a Saab?
With code P0340 your engine controller limits torque and you loose a good third of your available power. When you replaced coil packs did you use aftermarket or genuine Saab and are all 4 coil packs the same manufacturer?
Where can I buy coil packs for a Saab?
I gaped all 4 plugs at .035, and the coil packs (28347707) are from Profession Parts Sweden also known as Proparts. They specialize in Saab and Volvo car parts. I ordered them from eEuroparts.com they cost about $44 each.
What is the diagnostic code for Saab p1312?
The description of the P1312 code is: “Combustion detection cylinder 1+2, open circuit / short to B+”. As diagnostic help is following added: “Fault diagnosis concerns an electrical fault in the connecting leads.”.
What kind of platform does the Saab 9-3 have?
The 9-3 was first based on the GM2900 platform and subsequently changed to the GM Epsilon platform. Other vehicles using this platform included the Opel Vectra and Cadillac BLS. Saab’s last owners, National Electric Vehicle Sweden (NEVS) were assembling the 9-3 sedan (saloon) as Saab’s only model.
Where are spark plugs located on a Saab 9-3?
The non-turbo models use a distributor, and leads to each spark plug, while the turbocharged engines utilise Saab’s Trionic engine management system with a Direct Ignition Module (or cassette) mounted at the top of the engine, directly connecting to the spark plugs.
When did the Saab 9-3 anniversary convertible come out?
Saab 9-3 Anniversary convertible (Australia) The first generation 9-3, an updated Saab 900 (NG) was launched in 1998 for the 1999 model year. It was known to enthusiasts as the OG 9-3 (old generation) and internally as body style 9400. It continued as a full line through the 2002 model year.
Is the P0420 DTC code a trouble code?
The P0420 code is a very popular one and that’s why there’s a site dedicated to that specific trouble code. If your car’s check engine light is on, get that code read in case it’s a P0420. A P0420 code is a trouble code on OBD-II equipped vehicles.
With code P0340 your engine controller limits torque and you loose a good third of your available power. When you replaced coil packs did you use aftermarket or genuine Saab and are all 4 coil packs the same manufacturer?
What kind of spark plug does a genuine Saab use?
Gap 1.0-.9mm NGKBCPR6ES – 11 91 17 565 9000 B234 Nat. Asp. with DI 9-5 B235 TURBO NGKBKR7ES -11 91 71 307 9-5 B308 V6 NGKPFR7H – 10 91 88 681 Discontinued > Use NGKPFR6H – 10 Hard Use only. Prone to cold fouling on short trips. (HOT T7 cars) 9-3 B205 TURBO 185 HP (2000>) 9-3 B205 TURBO 205 HP
What does a bad camshaft position sensor code mean?
Once your car’s computer detects a CMP sensor failure, it will trigger the engine light and store a diagnostic trouble code (DTC) in its memory (see the table below for common camshaft position sensor trouble diagnostic codes). IV. CMP Codes and What They Mean