Can a power steering pump be changed on a Pontiac Grand Am?
Internal failure of power steering pump components or cracks on the pump case itself may lead to issues with driving. It is almost impossible to service a pump in such cases unless you have specialized equipment. However, following these steps, you will be able to change the power steering pump on your Pontiac Grand Am.
How do you replace a power steering pump?
Turn the nut on the installer shaft clockwise until the pulley is installed on the pump shaft. Unscrew the installer from the power steering pump shaft. Place the power steering belt over the pulley. Slide the power steering pump away from the engine and tighten the adjusting nut.
Where can I find Pontiac Grand Am parts?
Their products including Grand Am car makes and models, car parts and auto accessories including used car parts, aftermarket car parts, custom car parts, new car parts,old car parts or classic car parts and performance car parts can be found in almost everywhere including the net.
Where is the power steering pump on a minivan?
The pump will be somewhere on the front of the engine with the other accessories. On the typical GM longitudinally mounted V8, for example, the power steering pump will be right behind the radiator (though not necessarily up high and within easy reach). The car seen here is a front-wheel-drive Chrysler-built minivan with a 3.3-liter V6.
Where can I get a power steering pump?
If you need a power steering pump or other steering components, visit O’Reilly Auto Parts. We carry power steering pumps, hoses, and even complete rack and pinion units for most cars, trucks, and SUVs. When autocomplete results are available use up and down arrows to review and enter to select.
How many stars does masterpro power steering pump get?
Filter your results by entering your Year, Make, Model to ensure you find the parts that fit your vehicle. 3.8 out of 5 stars. Read reviews for MasterPro Power Steering Pump – Remanufactured
What causes a power steering pump to fail?
It is usually connected to the rack and pinion or steering gearbox. When it begins to fail, you may notice squealing noises or stiff steering. This may also be caused by a loose or damaged belt, so make sure and check its condition before replacing the pump.
How do you install a power steering pump?
Lift the steering pump off the engine compartment by hand. Set the new power steering pump in place by hand, install the mounting bolts and torque to 19-foot lbs (26 Nm). Install the hoses on the pump, connect the EVAP purge solenoid valve, upper air cleaner assembly and duct.
How to disable the air bag in a Pontiac Grand Am?
Disable the air bag system if your Pontiac Grand Am is equipped with it. Make sure the front wheels are pointing ahead to the front of the car and the ignition switch is in the OFF position. Remove all the fuses related to the air bag system–consult your vehicle service manual if necessary.
How can I get power steering fluid out of my car?
Remove the floor jack from underneath the engine. Fill the pump with power steering fluid using a funnel if necessary and bleed the system. Start the engine and turn the steering wheel completely from side to side; check the steering fluid frequently and add as needed until you purge the air from the system.
Internal failure of power steering pump components or cracks on the pump case itself may lead to issues with driving. It is almost impossible to service a pump in such cases unless you have specialized equipment. However, following these steps, you will be able to change the power steering pump on your Pontiac Grand Am.
Lift the steering pump off the engine compartment by hand. Set the new power steering pump in place by hand, install the mounting bolts and torque to 19-foot lbs (26 Nm). Install the hoses on the pump, connect the EVAP purge solenoid valve, upper air cleaner assembly and duct.
Disable the air bag system if your Pontiac Grand Am is equipped with it. Make sure the front wheels are pointing ahead to the front of the car and the ignition switch is in the OFF position. Remove all the fuses related to the air bag system–consult your vehicle service manual if necessary.
Remove the floor jack from underneath the engine. Fill the pump with power steering fluid using a funnel if necessary and bleed the system. Start the engine and turn the steering wheel completely from side to side; check the steering fluid frequently and add as needed until you purge the air from the system.
How do you remove a power steering pump?
Place a catch pan on the floor directly underneath the steering pump. Disconnect the hoses by loosening the clamps. You’ll need a regular screwdriver, Phillips screwdriver or ratchet and socket. Remove the mounting bolts from the power steering pump using a wrench or ratchet and socket. Lift the steering pump off the engine compartment by hand.
How big does a power steering pump need to be?
Torque the pump mounting bolts to 25 foot lbs. (34 Nm) if you have a 3.4L engine; install the drive belt and upper engine mount. Remove the floor jack from underneath the engine. Fill the pump with power steering fluid using a funnel if necessary and bleed the system.
Place a catch pan on the floor directly underneath the steering pump. Disconnect the hoses by loosening the clamps. You’ll need a regular screwdriver, Phillips screwdriver or ratchet and socket. Remove the mounting bolts from the power steering pump using a wrench or ratchet and socket. Lift the steering pump off the engine compartment by hand.
Torque the pump mounting bolts to 25 foot lbs. (34 Nm) if you have a 3.4L engine; install the drive belt and upper engine mount. Remove the floor jack from underneath the engine. Fill the pump with power steering fluid using a funnel if necessary and bleed the system.