Why does my Pontiac G6 make a clunking sound when steering?
Lubricating the “I” shaft only solves part of the problem and is really only a “band-aid” repair. The main problem is the strut bearings. You will most likely find that your strut bearings are starting to seize, causing a clunking sound when steering slowly.
What to do when your steering wheel clicks?
1. Remove the intermediate shaft pinch bolt at the steering gear end. 2. Install a new bolt, GM P/N 26058124 (Chevrolet, Pontiac) or P/N 26046722 (Saturn), but do not tighten the bolt at this time. 3. Pry the clamp up using a pry bar to position the bolt into the upper part of the groove as shown above. This will position the clamp off the bevel.
Why does my steering wheel clunk when I Sit Down?
Sometimes the noise may be duplicated when the vehicle is sitting still and the steering wheel is turned 90 degrees in either direction before initially centering the steering wheel. The clunk noise may be caused by a slip/stick condition between the inner and outer components of the intermediate shaft.
Where is the foam bracket on a Pontiac G6?
Install the three pieces of foam to the attaching bracket starting at the top center inside the bracket and proceed down across the fuel lines, then at the inside of the bracket at the left and right positions of the center piece of foam.
Lubricating the “I” shaft only solves part of the problem and is really only a “band-aid” repair. The main problem is the strut bearings. You will most likely find that your strut bearings are starting to seize, causing a clunking sound when steering slowly.
Why does my steering wheel make a clicking noise?
Some customers may comment on a knocking or rattling type noise from the front of the vehicle when driven at low speeds and over bumps. The noise only occurs when the steering wheel is in the straight ahead position and sounds like the noise is in the left suspension of the vehicle or directly in front of the driver.
When does a Chevy Malibu make a rattling noise?
This condition ONLY applies to 2004-2007 Chevrolet Malibu/Maxx and 2005-2007 Pontiac G6. Some customers may comment on a knocking or rattling type noise from the front of the vehicle when driven at low speeds and over bumps.
Install the three pieces of foam to the attaching bracket starting at the top center inside the bracket and proceed down across the fuel lines, then at the inside of the bracket at the left and right positions of the center piece of foam.
How do you get grease out of a Pontiac G6?
Extend the intermediate shaft all the way. Using the intermediate shaft grease kit, P/N 26098237, inject the grease into the gap between the inner shaft and the outer shaft as you are collapsing the shaft. This will draw the grease into the shaft.
Some customers may comment on a knocking or rattling type noise from the front of the vehicle when driven at low speeds and over bumps. The noise only occurs when the steering wheel is in the straight ahead position and sounds like the noise is in the left suspension of the vehicle or directly in front of the driver.
What can I do about rattling steering column?
Hey everyone, do you ever here a rattling or clanking noise coming from the steering column and it just bugs the crap out you, well look nor further because I fixed this problem in my truck today and all you need it is a 2 inch muffler clamp or hose clamp.
Sometimes the noise may be duplicated when the vehicle is sitting still and the steering wheel is turned 90 degrees in either direction before initially centering the steering wheel. The clunk noise may be caused by a slip/stick condition between the inner and outer components of the intermediate shaft.
1. Remove the intermediate shaft pinch bolt at the steering gear end. 2. Install a new bolt, GM P/N 26058124 (Chevrolet, Pontiac) or P/N 26046722 (Saturn), but do not tighten the bolt at this time. 3. Pry the clamp up using a pry bar to position the bolt into the upper part of the groove as shown above. This will position the clamp off the bevel.
Why does my Pontiac G6 make a clunking noise?
The clunk noise may be caused by a slip/stick condition between the inner and outer components of the intermediate shaft. Revised design intermediate shafts went into production in the 2009 model year and are the only design currently available through GMSPO since approximately September 2008.
Extend the intermediate shaft all the way. Using the intermediate shaft grease kit, P/N 26098237, inject the grease into the gap between the inner shaft and the outer shaft as you are collapsing the shaft. This will draw the grease into the shaft.
What makes a cracking noise when turning the steering wheel?
Clunking/cracking noise when turing steering wheel. Listen to the noise in video when turning the steering wheel! Front bearings (on struts) worn out. Noise is from springs snapping.. First I thought problem were due to bad sway bar link. Cost to fix at mechanic: Strut bearings, mount and Mechanics time came to a total of ~210 Euro…. Loading…
Clunking/cracking noise when turing steering wheel. Listen to the noise in video when turning the steering wheel! Front bearings (on struts) worn out. Noise is from springs snapping.. First I thought problem were due to bad sway bar link. Cost to fix at mechanic: Strut bearings, mount and Mechanics time came to a total of ~210 Euro…. Loading…
Are there any problems with the Pontiac G6?
The 2006 G6 also has an expensive problem with “popping” or “clunking” noises when turning, & that issue extends to newer model years as well. Factor in the 2006 Pontiac G6’s poor side impact protection & you end up with a vehicle you should steer clear of. Click on a category below for details. Help? Loading …
How much does it cost to fix a GM G6?
G6 owners typically report spending $600 – $1,200+ to fix the problem, replacing either the entire steering column or the power assist motor. In March 2010, GM recalled 1.3 million vehicles for this exact problem “…after receiving 1,100 complaints of power steering failures.”