How many quarts of oil does my 2012 Dodge journey take?
When equipped with the 2.4-liter engine, the 2012 Dodge Journey useS4. 2 liters (4.5 quarts) of SAE 5W-20 oil.
What kind of oil does a 2012 Dodge journey take?
5W-30
Engine Oil
| Viscosity: | 5W-30 (All TEMPS) |
|---|---|
| Capacity: | 5.9 quarts (with filter)After refill check oil level. |
| Torque: | 20 ft/lbs (Oil Drain Plug) |
| Notes: | Miniature Lamp – Boxed; Compare to Original;Glass:Clear (T5),# of Filaments:1,Watts:10.24,Base:Printed circuit,OE Type |
Does a 2012 Dodge Journey take synthetic oil?
They type of oil You will need to use in Your 2012 Dodge Journey is dependent on which engine You have in Your vehicle. Models equipped with the factory standard 2.4L engine will need to use 5W-20 synthetic blend oil while models equipped with the upgraded 3.6L V6 engine will need to use 5W-30 synthetic blend.
What is the best oil for a Dodge Journey?
Dodge recommends that You use fully synthetic SAE 5W-20 oil when it is time to change it. Oil comes in two major varieties, conventional and synthetic.
What to do when you need to change the oil on a Dodge Journey?
Make sure the Journey’s interior and exterior lights are working properly. Your Dodge Journey’s Oil Change Indicator System will let you know when you need to change your oil. Change your oil and oil filter. Rotate the Journey’s tires. Inspect your vehicle battery. Clean and tighten its terminals as needed.
How to reset the journey oil change reminder?
Dodge Journey Oil Change Due Reminder Reset. 1 STEP 3. Push the start button to RUN Position (Ignition On) Don’t start the engine. 2 STEP 4. 3 STEP 5.
Where is the oil filter cap on a Dodge Journey?
The round black plastic oil filter cap is located on the left side of the engine near the oil filler cap. Attach the 24mm socket and 1/2″ drive ratcheting wrench to the hex head on the top of the oil filter cap.
How to do an oil change on a jeep?
To reset the “Oil Change Due” or “Oil Change Required” message on the display, follow these steps: 1. Turn the ignition to the “Run” position (or press the “Engine Start/Stop” button twice) but do not start the engine. 2. Press the accelerator (gas) pedal down to the floor 3 times within 10 seconds.
How to change the oil on a Dodge Journey 3.6?
How to Change the oil on a 2013 Dodge Journey 3.6 – YouTube Step by step Step by step AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features © 2021 Google LLC
To reset the “Oil Change Due” or “Oil Change Required” message on the display, follow these steps: 1. Turn the ignition to the “Run” position (or press the “Engine Start/Stop” button twice) but do not start the engine. 2. Press the accelerator (gas) pedal down to the floor 3 times within 10 seconds.
How to change oil in Dodge Journey Pentastar?
Loosen the oil drain bolt by turning it counter clockwise with the 13mm socket and ratcheting wrench. Spin out the bolt and allow the old oil to drain out for at least a few minutes. Replace the 13mm oil drain bolt and tighten it in the clockwise direction to just past hand tight or about 20-25 ft-lbs of torque.
How to change the oil in a Nissan D21?
1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open 3. Find Oil Drain – Locate the oil drain plug underneath the vehicle 4. Drain Oil – Set up the workspace, drain oil and replace plug 5. Find Oil Filter – Locate the oil filter 6. Remove Filter – Position drain pan and remove the oil filter 7.