Where is the cam position sensor on a Nissan Frontier?
There’s a picture on page EC-325 of the factory service manual. The cam position sensor is located on the back side of the cylinder head, just below the valve cover and just above the engine coolant temp sensor. There’s a picture of it on page EC-332.
What’s the code for the camshaft position sensor?
I just joined this forum to figure this problem out and see if it is something I can tackle and save $600 from the dealer. Pulled the code PO340 camshaft position sensor Bank 1. Dealer “recommended” to replace both, but just going to tackle Bank 1 first and test.
Which is Bank 2 on a Nissan Frontier?
This is for P0345 which is bank 2 drivers side, bank 1 would give you a P0340 code. This is how to do it. Youll have to follow the pic’s at the bottom, I don’t know how to put them in as I go.
Where is my camshaft position sensor located?
The camshaft position sensor is located on top of the engine near the ignition coils. The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
Where is camshaft position sensor located?
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils. The camshaft position sensor is located on the engine near the camshaft pulley.
Where is the camshaft position sensor?
The Camshaft Position (CMP) Sensor is located in the right side of the engine compartment at the rear of the valve cover, near the intake manifold.
Where to find crankshaft position sensor?
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose. The crankshaft position sensor is located on the engine near the crankshaft pulley. The crankshaft position sensor is located at the front of the engine near the timing belt.
Is the camshaft position sensor part of the distributor?
Nissan models with distributor the camshaft position sensor is part of the distributor. There is a factory service bulletin for the following Nissan models: 2003 Nissan Altima. 2004 Nissan Altima. 2005 Nissan Altima. 2004 Nissan Quest. 2004 Nissan Maxima. Nissan Factory Service Bulletin OBDII Code P0340.
What causes a Nissan camshaft sensor to malfunction?
P0340 NISSAN Possible Causes 1 Faulty Camshaft Position Sensor 2 Camshaft Position Sensor harness is open or shorted 3 Camshaft Position Sensor circuit poor electrical connection 4 Faulty starter motor 5 Starting system circuit 6 Dead (Weak) battery
What’s the crankshaft position sensor on a frontier?
I’ve got a 2006 Frontier SE 4.0 w/ 85k miles. Yesterday on my commute home, I was using Cruise Control, traffic slowed, so I cancelled cruise. A few seconds later the RPM’s dropped to 0 for a split second, SES light comes on for about 2-3 seconds and then turns off.
There’s a picture on page EC-325 of the factory service manual. The cam position sensor is located on the back side of the cylinder head, just below the valve cover and just above the engine coolant temp sensor. There’s a picture of it on page EC-332.
When do I need to replace the camshaft position sensor?
Had to replace my camshaft position sensor after having some issues with hard starting and stalling. If you have the P0345 code you will most likely need to replace the sensor. This is for P0345 which is bank 2 drivers side, bank 1 would give you a P0340 code.
This is for P0345 which is bank 2 drivers side, bank 1 would give you a P0340 code. This is how to do it. Youll have to follow the pic’s at the bottom, I don’t know how to put them in as I go.