What should I do if my starter motor is out?
Like he said, most likely is your battery. However, when the hold in coil is out on the starter solenoid it will do the same thing that you are just describing. In that case you need a new starter motor or you could try to rebuild your solenoid. The starter motor and is very easy to swap out. First, disconnect your battery. Do not skip this step.
What should I do if my motorcycle battery wont start?
If you don’t see these symptoms or are otherwise unsure what to look for, the first step is ensuring that the battery is operational and providing the maximum voltage. To confirm your battery is still good, you should visually inspect it, check the voltage, and load test the battery. A visual battery inspection should involve:
Can a bad starter relay be a solenoid problem?
Sometimes the starter itself is the problem. Electrical issues can be annoying and inconvenient. They can also be hazardous and can cause damage. If you run into symptoms of a bad starter relay or solenoid with your car, truck, or SUV, make sure to have a trusted technician to diagnose the specific problem.
Why does my XT curcuit run without a battery?
Water and moisture in couplings too. Check the battey next..Its NOT the battery that runs the bike or the lights etc, its the generator. The battery is there to start the bike, no other reason. I cant remember how the XT curcuit runs, will it run with and without a battery in place ??
When to know if your motorcycle battery is operable?
If the battery drops below 10.8 volts, it is possible that the battery is no longer operable. Significant engine trouble can also cause the voltage to drop too far if it is making it difficult for the starter to turn the engine over. A good way to tell if this is happening is to check the battery cables for excessive heat.
Is it possible to start a motorcycle with a bad battery?
It’s possible for your motorcycle to start and run with a bad battery, but that can create even more problems like causing the bike to run poorly and miss. It’s also important to make sure that the battery that you use produces enough amps to properly power all of the electrical components.
Can a bad battery cause a car to not start?
Sometimes your car starts, sometimes it doesn’t. Intermittent operation can be a sign of a failing starter solenoid. Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine. Blown fuse – Sometimes the simplest explanation is the best one.
Water and moisture in couplings too. Check the battey next..Its NOT the battery that runs the bike or the lights etc, its the generator. The battery is there to start the bike, no other reason. I cant remember how the XT curcuit runs, will it run with and without a battery in place ??
Why does my starter click when trying to start?
The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful?
What to do when your motorbike wont start?
Look up direct start button cover. It can get you out of a jam when the solenoid acts up. Won’t help if the battery is to low to crank the engine though. Was this answer helpful? I dont own a motorbike.
Why is my Harley Davidson Road King not starting?
If you have a Tachometer, disconnect it. A bad tach can interrupt proper coil function. i have problem error code U1301 in Harley Davidson Road King 2009 and test everything not starts . I have a 92 FXRSP, I recently replaced my switches and I had a new battery.
What’s the voltage on a Harley Davidson starter?
I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.
Why is my starter not working on my Harley?
That black wire with the red tracer should be sending 12v to the starter relay. Be sure that this wire is not damaged or pinched anywhere in its travel. This will be more common when wires have been routed through the bars, or switch housings/switches have been changed. Don’t forget to use your multimeter inside the switch housings too.
Like he said, most likely is your battery. However, when the hold in coil is out on the starter solenoid it will do the same thing that you are just describing. In that case you need a new starter motor or you could try to rebuild your solenoid. The starter motor and is very easy to swap out. First, disconnect your battery. Do not skip this step.
When is it time to replace the solenoid?
Have battery tested at auto parts store, a lot offer free battery testing and can give you print out of the status on battery. If connections and wires (positive and negative) all look good then it is probably time to check and rebuild/replace solenoid.
What makes the solenoid hold in coil click?
The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful? What is the holding coil?
How do you retract starter solenoid on Harley Davidson?
Connect the free clip to the starter relay terminal on the left side of the starter solenoid. The solenoid pinion gear, exposed at the inner face of the solenoid, should click and retract into the starter housing. The starter solenoid is defective if the pinion gear does not retract.
How does the solenoid work on a Harley Davidson?
When power is applied to the solenoid, a retractable pinion gear is pulled into place between the engine’s starter clutch and the starter motor. This action is followed by a distinct click before the engine is cranked to life.
What to do if your starter solenoid is not working?
Remove the solenoid for inspection if it did not click. If the voltmeter did not provide a 12-volt reading, there is a problem between the starter and the starter button. Turn the ignition switch to the “Off” position and remove the seat from the motorcycle, using either a flat-head screwdriver or by unscrewing the seat bolt by hand.
What to do if your starter does not work on a Harley Davidson?
If the voltmeter did not provide a 12-volt reading, there is a problem between the starter and the starter button. Turn the ignition switch to the “Off” position and remove the seat from the motorcycle, using either a flat-head screwdriver or by unscrewing the seat bolt by hand.