How do you tighten a snowmobile drive belt?
To adjust the belt, loosen the jam nut on the secondary clutch using an Allen wrench. Turn the adjuster counterclockwise to draw the sheaves together. Grab ahold of the belt and roll it through the primary and through the secondary. You’ll see the belt rise in the secondary sheaves, which causes it to tighten.
Why is my new snowmobile belt squealing?
Belt noise is usually a sign of improper belt installation. If you have a constant squeal, the tension may be too tight. You can fix this by lowering the belt in the secondary. If you have a chirping noise your belt may be too loose.
What is belt span?
A tensiometer is a tool that measures the force required to move the tensiometer plunger a given distance. This force can be compared to a table of recommended tension forces to determine the status of the belt.
How many miles should a snowmobile belt last?
You can usually expect your belt to last somewhere between 1500-2000 miles before it will need to be replaced.
How to replace the drive belt on a Polaris ATV?
Always wear safety glasses and nitrile gloves when servicing your Polaris ATV. To inspect or replace the drive belt on your Sportsman 850 or Sportsman XP 1000, follow these steps: 1. Park the vehicle on a flat, level surface. 2. Ensure the vehicle is in PARK. 3. Set the parking brake.
How to set alignment, belt deflection and adjust Polaris?
If you need to move the clutch out to increase offset, remove the clutch, add a shim, then remove the same thickness shim from the bolt. There should be some free play (1/16″) of the clutch on the jackshaft. That helps in keeping the clutch aligned and also keeps the clutch from side-loading the jackshaft bearing.
What kind of belt do I need for my Polaris Ranger?
SuperATV Heavy-Duty Extreme Badass Drive Belt for 2015-2020 Polaris Ranger 500/570 / 570 Crew (See Fitment) | Built for high temps and extreme abuse! . . SuperATV Heavy Duty Extreme Badass CVT Drive Belt for 2013-2019 Polaris Ranger XP 900 / Ranger XP 900 Crew | Built for high temps and extreme abuse!
How to replace the drive belt on a sportsman 850?
To inspect or replace the drive belt on your Sportsman 850 or Sportsman XP 1000, follow these steps: 1. Park the vehicle on a flat, level surface. 2. Ensure the vehicle is in PARK. 3. Set the parking brake. 4. Remove the seat by lifting up on the rear and pulling back. 5.
How to change the drive belt on a Polaris Sportsman?
In this video John shows you how to replace a Polaris Sportsman drive belt, including how to remove the frame brace, remove the outer cover, release tension on the primary clutch driven sheath, and how to use a spreader wrench to open the clutch sheath and remove the drive belt.
How to change belt and adjust drive belt tension?
Set the parking brake. Grab the inner sheave on the secondary and rotate it clockwise while pulling up on the belt. The clutch will open and the belt will “fall in”. From here, you can hold the clutch open while you work it around to take it off and put the new one on.
What is the belt number on a sportsman 570?
If replacing the belt, the part number on the belt should face outward when installed. The belt is part number 3211229. 22. Loop the belt over the drive clutch and begin to walk it over the driven clutch sheave. 23. Once the belt is installed, turn the clutch spreader tool counterclockwise to remove from the driven clutch.
Why is shift lever so hard to move on Polaris ATV?
Ok guys while the ATV is drying off after washing the PO mud off I pulled the clutch cover to see if I could find why it is so hard to move the shift lever when running. I found the primary hub is rubbing the belt on the out side edge of the hub all the time and the inside edge has .080 clearance on the motor side.